scholarly journals Carbon Nanofibers-Poly-3-hydroxyalkanoates Nanocomposite: Ultrasound-Assisted Dispersion and Thermostructural Properties

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
A. M. Gumel ◽  
M. S. M. Annuar ◽  
K. A. Ishak ◽  
N. Ahmad
Keyword(s):  
Carbon Nanofibers ◽  
High Surface ◽  
Volume Ratio ◽  
Thermomechanical Properties ◽  
Stimuli Responsive ◽  
Ultrasound Exposure ◽  
Power Intensity ◽  
Medium Chain Length ◽  
The Stability ◽  
Microscopic Morphology

The conductivity and high surface-to-volume ratio of carbon nanofibers (CNFs) composited with the medium-chain-length poly-3-hydroxyalkanoate (mcl-PHA) have attracted much attention as smart biomaterial. However, poor CNF dispersion leads to tactoid agglomerated composite with poor crystallite morphology resulting in inferior thermomechanical properties. We employed acoustic sonication to enhance the construction of exfoliated PHA/CNFs nanocomposites. The effects of CNF loading and the insonation variables (power intensity, frequency, and time) on the stability and microscopic morphology of the nanocomposites were studied. Sonication improved the dispersion of CNFs into the polymer matrix, thereby improving the physical morphology, crystallinity, and thermomechanical properties of the nanocomposites. For example, compositing the polymer with 10% w/w CNF resulted in 66% increase in crystallite size, 46% increase in micromolecular elastic strain, and 17% increase in lattice strain. Nevertheless, polymer degradation was observed following the ultrasound exposure. The constructed bionanocomposite could potentially be applied for organic electroconductive materials, biosensors and stimuli-responsive drug delivery devices.

scholarly journals Carbon-Nanofibers-Based Micro-/Nanodevices for Neural-Electrical and Neural-Chemical Interfaces

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Hongzhi Zhang ◽  
Mei Yu ◽  
Lei Xie ◽  
Linlin Jin ◽  
Zhe Yu
Keyword(s):  
Carbon Nanofibers ◽  
High Surface ◽  
Volume Ratio ◽  
Nerve Tissue ◽  
Closed Loop System ◽  
Nanofibrous Scaffolds ◽  
Interface Devices ◽  
Further Development ◽  
Fine Tune

Carbon nanofibers (CNFs) have shown great potentials for development of micro-/nanodevices for neural interfaces due to their suitable properties, such as chemical stability, good electrical conductivity, ultramicro size with low electrical impedance, 3D structures with high surface-to-volume ratio, and long-term biocompatibility. In this paper, we review the applications of CNFs as neural-electrical interfaces and neural-chemical interfaces for neural recording and stimulation, electroconductive nanofibrous scaffolds for nerve tissue engineering, drug and gene delivery, and neurochemical sensing. The CNFs-based micro-/nanodevices provide new platforms to fine-tune electrical and chemical cues of neurons at subcellular nanoscale, which can be used for both fundamental studies of material-cell interactions and the development of chronically stable, implantable neural interface devices. Further development of this technology may potentially enable a highly multiplex closed-loop system with multifunctions for neuromodulation and neuroprostheses.

scholarly journals Antioxidant Network Based on Sulfonated Polyhydroxyalkanoate and Tannic Acid Derivative

2021 ◽  
Vol 8 (1) ◽  
pp. 9
Author(s):  
Laura Brelle ◽  
Estelle Renard ◽  
Valerie Langlois
Keyword(s):  
Gallic Acid ◽  
Tannic Acid ◽  
Water Soluble ◽  
Gel Formation ◽  
Ene Reaction ◽  
Inorganic Cations ◽  
Medium Chain Length ◽  
Physically Crosslinked ◽  
The Stability ◽  
Derivatives Of

A novel generation of gels based on medium chain length poly(3-hydroxyalkanoate)s, mcl-PHAs, were developed by using ionic interactions. First, water soluble mcl-PHAs containing sulfonate groups were obtained by thiol-ene reaction in the presence of sodium-3-mercapto-1-ethanesulfonate. Anionic PHAs were physically crosslinked by divalent inorganic cations Ca2+, Ba2+, Mg2+ or by ammonium derivatives of gallic acid GA-N(CH3)3+ or tannic acid TA-N(CH3)3+. The ammonium derivatives were designed through the chemical modification of gallic acid GA or tannic acid TA with glycidyl trimethyl ammonium chloride (GTMA). The results clearly demonstrated that the formation of the networks depends on the nature of the cations. A low viscoelastic network having an elastic around 40 Pa is formed in the presence of Ca2+. Although the gel formation is not possible in the presence of GA-N(CH3)3+, the mechanical properties increased in the presence of TA-N(CH3)3+ with an elastic modulus G’ around 4200 Pa. The PHOSO3−/TA-N(CH3)3+ gels having antioxidant activity, due to the presence of tannic acid, remained stable for at least 5 months. Thus, the stability of these novel networks based on PHA encourage their use in the development of active biomaterials.

scholarly journals Polyhydroxyalkanoate Nanoparticles for Pulmonary Drug Delivery: Interaction with Lung Surfactant

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1482
Author(s):  
Olga Cañadas ◽  
Andrea García-García ◽  
M. Auxiliadora Prieto ◽  
Jesús Pérez-Gil
Keyword(s):  
Drug Delivery ◽  
Drug Delivery Systems ◽  
Bacterial Species ◽  
High Surface ◽  
Lung Surfactant ◽  
Delivery Systems ◽  
Pulmonary Drug Delivery ◽  
Epifluorescence Microscopy ◽  
Energy Storage Materials ◽  
The Stability

Polyhydroxyalkanoates (PHA) are polyesters produced intracellularly by many bacterial species as energy storage materials, which are used in biomedical applications, including drug delivery systems, due to their biocompatibility and biodegradability. In this study, we evaluated the potential application of this nanomaterial as a basis of inhaled drug delivery systems. To that end, we assessed the possible interaction between PHA nanoparticles (NPs) and pulmonary surfactant using dynamic light scattering, Langmuir balances, and epifluorescence microscopy. Our results demonstrate that NPs deposited onto preformed monolayers of DPPC or DPPC/POPG bind these surfactant lipids. This interaction facilitated the translocation of the nanomaterial towards the aqueous subphase, with the subsequent loss of lipid from the interface. NPs that remained at the interface associated with liquid expanded (LE)/tilted condensed (TC) phase boundaries, decreasing the size of condensed domains and promoting the intermixing of TC and LE phases at submicroscopic scale. This provided the stability necessary for attaining high surface pressures upon compression, countering the destabilization induced by lipid loss. These effects were observed only for high NP loads, suggesting a limit for the use of these NPs in pulmonary drug delivery.

scholarly journals Electrospun Nanofibers for Sensing and Biosensing Applications—A Review

2021 ◽  
Vol 22 (12) ◽  
pp. 6357
Author(s):  
Kinga Halicka ◽  
Joanna Cabaj
Keyword(s):  
High Surface ◽  
High Surface Area ◽  
Toxic Metal ◽  
Volume Ratio ◽  
Electrospun Nanofibers ◽  
Clinical Diagnostics ◽  
Loading Capacity ◽  
Electrospun Nanofiber ◽  
Sensing Platforms ◽  
Different Types

Sensors and biosensors have found applications in many areas, e.g., in medicine and clinical diagnostics, or in environmental monitoring. To expand this field, nanotechnology has been employed in the construction of sensing platforms. Because of their properties, such as high surface area to volume ratio, nanofibers (NFs) have been studied and used to develop sensors with higher loading capacity, better sensitivity, and faster response time. They also allow to miniaturize designed platforms. One of the most commonly used techniques of the fabrication of NFs is electrospinning. Electrospun NFs can be used in different types of sensors and biosensors. This review presents recent studies concerning electrospun nanofiber-based electrochemical and optical sensing platforms for the detection of various medically and environmentally relevant compounds, including glucose, drugs, microorganisms, and toxic metal ions.

scholarly journals Study of the geometry of open channels in a layer-bed-type microfluidic immobilized enzyme reactor

2021 ◽  
Author(s):  
Cynthia Nagy ◽  
Robert Huszank ◽  
Attila Gaspar
Keyword(s):  
Immobilized Enzyme ◽  
High Surface ◽  
Volume Ratio ◽  
Volumetric Flow Rate ◽  
Enzyme Reactor ◽  
Channel Pattern ◽  
Immobilized Enzyme Reactor ◽  
Split Flow ◽  
Parallel Streams ◽  
Enzymatic Microreactors

AbstractThis paper aims at studying open channel geometries in a layer-bed-type immobilized enzyme reactor with computer-aided simulations. The main properties of these reactors are their simple channel pattern, simple immobilization procedure, regenerability, and disposability; all these features make these devices one of the simplest yet efficient enzymatic microreactors. The high surface-to-volume ratio of the reactor was achieved using narrow (25–75 μm wide) channels. The simulation demonstrated that curves support the mixing of solutions in the channel even in strong laminar flow conditions; thus, it is worth including several curves in the channel system. In the three different designs of microreactor proposed, the lengths of the channels were identical, but in two reactors, the liquid flow was split to 8 or 32 parallel streams at the inlet of the reactor. Despite their overall higher volumetric flow rate, the split-flow structures are advantageous due to the increased contact time. Saliva samples were used to test the efficiencies of the digestions in the microreactors. Graphical abstract

scholarly journals A Review on Biosensors and Recent Development of Nanostructured Materials-Enabled Biosensors

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1109
Author(s):  
Varnakavi. Naresh ◽  
Nohyun Lee
Keyword(s):  
High Surface ◽  
Three Dimensional ◽  
Biological Response ◽  
Volume Ratio ◽  
Recent Decade ◽  
Disease Diagnosis ◽  
Electrical Signal ◽  
Detection Sensitivity ◽  
Wide Range ◽  
Color Tunability

A biosensor is an integrated receptor-transducer device, which can convert a biological response into an electrical signal. The design and development of biosensors have taken a center stage for researchers or scientists in the recent decade owing to the wide range of biosensor applications, such as health care and disease diagnosis, environmental monitoring, water and food quality monitoring, and drug delivery. The main challenges involved in the biosensor progress are (i) the efficient capturing of biorecognition signals and the transformation of these signals into electrochemical, electrical, optical, gravimetric, or acoustic signals (transduction process), (ii) enhancing transducer performance i.e., increasing sensitivity, shorter response time, reproducibility, and low detection limits even to detect individual molecules, and (iii) miniaturization of the biosensing devices using micro-and nano-fabrication technologies. Those challenges can be met through the integration of sensing technology with nanomaterials, which range from zero- to three-dimensional, possessing a high surface-to-volume ratio, good conductivities, shock-bearing abilities, and color tunability. Nanomaterials (NMs) employed in the fabrication and nanobiosensors include nanoparticles (NPs) (high stability and high carrier capacity), nanowires (NWs) and nanorods (NRs) (capable of high detection sensitivity), carbon nanotubes (CNTs) (large surface area, high electrical and thermal conductivity), and quantum dots (QDs) (color tunability). Furthermore, these nanomaterials can themselves act as transduction elements. This review summarizes the evolution of biosensors, the types of biosensors based on their receptors, transducers, and modern approaches employed in biosensors using nanomaterials such as NPs (e.g., noble metal NPs and metal oxide NPs), NWs, NRs, CNTs, QDs, and dendrimers and their recent advancement in biosensing technology with the expansion of nanotechnology.

scholarly journals Water uptake of various electrospun nonwovens

2020 ◽  
Vol 6 (3) ◽  
pp. 155-158
Author(s):  
Katharina Wulf ◽  
Volkmar Senz ◽  
Thomas Eickner ◽  
Sabine Illner
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Water Absorption ◽  
Water Uptake ◽  
Biomedical Applications ◽  
High Surface ◽  
Volume Ratio ◽  
Polymer Composition ◽  
Water Wetting ◽  
Morphology Changes

AbstractIn recent years, nanofiber based materials have emerged as especially interesting for several biomedical applications, regarding their high surface to volume ratio. Due to the superficial nano- and microstructuring and the different wettability compared to nonstructured surfaces, the water absorption is an important parameter with respect to the degradation stability, thermomechanic properties and drug release properties, depending on the type of polymer [1]. In this investigation, the water absorption of different non- and plasma modified biostable nanofiber nonwovens based on polyurethane, polyester and polyamide were analysed and compared. Also, the water absorption by specified water wetting, the contact angle and morphology changes were examined. The results show that the water uptake is highly dependent on the surface modification and the polymer composition itself and can therefore be partially changed.

scholarly journals Solar-blind ultraviolet photodetector based on vertically aligned single-crystalline β-Ga2O3 nanowire arrays

Nanophotonics ◽  
2020 ◽  
Vol 9 (15) ◽  
pp. 4497-4503
Author(s):  
Liying Zhang ◽  
Xiangqian Xiu ◽  
Yuewen Li ◽  
Yuxia Zhu ◽  
Xuemei Hua ◽  
...  
Keyword(s):  
Inductively Coupled Plasma ◽  
Light Trapping ◽  
High Surface ◽  
Volume Ratio ◽  
Average Diameter ◽  
Nanowire Arrays ◽  
Etching Technique ◽  
Inductively Coupled ◽  
Solar Blind ◽  
Vertically Aligned

AbstractVertically aligned nanowire arrays, with high surface-to-volume ratio and efficient light-trapping absorption, have attracted much attention for photoelectric devices. In this paper, vertical β-Ga2O3 nanowire arrays with an average diameter/height of 110/450 nm have been fabricated by the inductively coupled plasma etching technique. Then a metal-semiconductor-metal structured solar-blind photodetector (PD) has been fabricated by depositing interdigital Ti/Au electrodes on the nanowire arrays. The fabricated β-Ga2O3 nanowire PD exhibits ∼10 times higher photocurrent and responsivity than the corresponding film PD. Moreover, it also possesses a high photocurrent to dark current ratio (Ilight/Idark) of ∼104 and a ultraviolet/visible rejection ratio (R260 nm/R400 nm) of 3.5 × 103 along with millisecond-level photoresponse times.

scholarly journals Design Considerations for Borehole Thermal Energy Storage (BTES): A Review with Emphasis on Convective Heat Transfer

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-26 ◽  
Author(s):  
Helge Skarphagen ◽  
David Banks ◽  
Bjørn S. Frengstad ◽  
Harald Gether
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Theoretical Calculations ◽  
High Surface ◽  
High Surface Area ◽  
Volume Ratio ◽  
Thermal Recovery ◽  
Conductive Heat ◽  
Geological Environment

Borehole thermal energy storage (BTES) exploits the high volumetric heat capacity of rock-forming minerals and pore water to store large quantities of heat (or cold) on a seasonal basis in the geological environment. The BTES is a volume of rock or sediment accessed via an array of borehole heat exchangers (BHE). Even well-designed BTES arrays will lose a significant quantity of heat to the adjacent and subjacent rocks/sediments and to the surface; both theoretical calculations and empirical observations suggest that seasonal thermal recovery factors in excess of 50% are difficult to obtain. Storage efficiency may be dramatically reduced in cases where (i) natural groundwater advection through the BTES removes stored heat, (ii) extensive free convection cells (thermosiphons) are allowed to form, and (iii) poor BTES design results in a high surface area/volume ratio of the array shape, allowing high conductive heat losses. The most efficient array shape will typically be a cylinder with similar dimensions of diameter and depth, preferably with an insulated top surface. Despite the potential for moderate thermal recovery, the sheer volume of thermal storage that the natural geological environment offers can still make BTES a very attractive strategy for seasonal thermal energy storage within a “smart” district heat network, especially when coupled with more efficient surficial engineered dynamic thermal energy stores (DTES).

Study on the Use of Rhodamine Doped Nanocomposite for Latent Fingerprint Detection

2011 ◽  
Vol 295-297 ◽  
pp. 813-816 ◽  
Author(s):  
Li Liu
Keyword(s):  
High Surface ◽  
Sol Gel ◽  
Volume Ratio ◽  
Molecular Complexes ◽  
Optical Devices ◽  
Chemical Compositions ◽  
Loading Capacity ◽  
Optical And Mechanical Properties ◽  
Fluorescent Compounds ◽  
Fingerprint Detection

Silicon dioxide-based nanocomposites offer large loading capacity for various doping chemicals or molecular complexes, high surface to volume ratio and customizable surface chemistry for the creation and development of novel sensors and devices [1-2]. When compared with other sol-gel materials, xerogels represent a class of nanocomposites that are relatively easy to fabricate but with unique thermal, acoustic, optical and mechanical properties for rapid sensor or device prototyping development [3-4]. Xerogels in solids are formed by controlled evaporation of the liquid in the hydro-gel. Their porosity and morphology depend largely on the temperature, gel chemical compositions and pH in the fabrication process. When impregnated with fluorescent compounds in their nanosize cavities, the doped xerogels exhibit strong and stable fluorescence properties that are useful for the developing of ion-exchange sensors and optical devices. However, the use of these fluorescently doped xerogels in forensic applications was still largely unexplored.

Sign in / Sign up

Export Citation Format

Share Document