scholarly journals Understanding the Crystallinity Indices Behavior of Burned Bones and Teeth by ATR-IR and XRD in the Presence of Bioapatite Mixed with Other Phosphate and Carbonate Phases

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Giampaolo Piga ◽  
David Gonçalves ◽  
T. J. U. Thompson ◽  
Antonio Brunetti ◽  
Assumpció Malgosa ◽  
...  
Keyword(s):  
Crystallinity Index ◽  
Mechanical Processing ◽  
Spectroscopy Data ◽  
X Ray Diffraction ◽  
Human Teeth ◽  
X Ray ◽  
Human Bones ◽  
Burned Bones ◽  
Tcp Phase ◽  
Xrd Patterns

We have critically investigated the ATR-IR spectroscopy data behavior of burned human teeth as opposed to the generally observed behavior in human bones that were subjected to heat treatment, whether deliberate or accidental. It is shown that the deterioration of the crystallinity index (CI) behavior sometimes observed in bones subjected to high temperature appears to be of higher frequency in the case of bioapatite from teeth. This occurs because the formation of the β-tricalcium phosphate (β-TCP) phase, otherwise known as whitlockite, clearly ascertained by the X-ray diffraction (XRD) patterns collected on the same powdered specimens investigated by ATR-IR. These results point to the need of combining more than one physicochemical technique even if apparently well suitable, in order to verify whether the assumed conditions assessed by spectroscopy are fully maintained in the specimens after temperature and/or mechanical processing.

scholarly journals Valorization of Byproducts of Hemp Multipurpose Crop: Short Non-Aligned Bast Fibers as a Source of Nanocellulose

Molecules ◽  
2021 ◽  
Vol 26 (16) ◽  
pp. 4723
Author(s):  
Sara Dalle Vacche ◽  
Vijayaletchumy Karunakaran ◽  
Alessia Patrucco ◽  
Marina Zoccola ◽  
Loreleï Douard ◽  
...  
Keyword(s):  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Cannabis Sativa ◽  
Crystallinity Index ◽  
Residual Lignin ◽  
Chemical Pretreatment ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bast Fibers ◽  
Seed Maturity

Nanocellulose was extracted from short bast fibers, from hemp (Cannabis sativa L.) plants harvested at seed maturity, non-retted, and mechanically decorticated in a defibering apparatus, giving non-aligned fibers. A chemical pretreatment with NaOH and HCl allowed the removal of most of the non-cellulosic components of the fibers. No bleaching was performed. The chemically pretreated fibers were then refined in a beater and treated with a cellulase enzyme, followed by mechanical defibrillation in an ultrafine friction grinder. The fibers were characterized by microscopy, infrared spectroscopy, thermogravimetric analysis and X-ray diffraction after each step of the process to understand the evolution of their morphology and composition. The obtained nanocellulose suspension was composed of short nanofibrils with widths of 5–12 nm, stacks of nanofibrils with widths of 20–200 nm, and some larger fibers. The crystallinity index was found to increase from 74% for the raw fibers to 80% for the nanocellulose. The nanocellulose retained a yellowish color, indicating the presence of some residual lignin. The properties of the nanopaper prepared with the hemp nanocellulose were similar to those of nanopapers prepared with wood pulp-derived rod-like nanofibrils.

scholarly journals Influence of Li2CO3 addition on electrical and magnetic properties of Ni0.6Mg0.4Fe2O4

2020 ◽  
Vol 10 (03) ◽  
pp. 2050003
Author(s):  
M. R. Hassan ◽  
M. T. Islam ◽  
M. N. I. Khan
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Low Frequency ◽  
Solid State Reaction Method ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Frequency Regime ◽  
Xrd Patterns

In this research, influence of adding Li2CO3 (at 0%, 2%, 4%, 6%) on electrical and magnetic properties of [Formula: see text][Formula: see text]Fe2O4 (with 60% Ni and 40% Mg) ferrite has been studied. The samples are prepared by solid state reaction method and sintered at 1300∘C for 6[Formula: see text]h. X-ray diffraction (XRD) patterns show the samples belong to single-phase cubic structure without any impurity phase. The magnetic properties (saturation magnetization and coercivity) of the samples have been investigated by VSM and found that the higher concentration of Li2CO3 reduces the hysteresis loss. DC resistivity increases with Li2CO3 contents whereas it decreases initially and then becomes constant at lower value with temperature which indicates that the studied samples are semiconductor. The dielectric dispersion occurs at a low-frequency regime and the loss peaks are formed in a higher frequency regime, which are due to the presence of resonance between applied frequency and hopping frequency of charge carriers. Notably, the loss peaks are shifted to the lower frequency with Li2CO3 additions.

Determination of crystallinity of Chinese handmade papers by means of X-ray diffraction

2020 ◽  
Vol 41 (2) ◽  
pp. 69-86
Author(s):  
Peng Liu ◽  
Hongbin Zhang ◽  
Sinong Wang ◽  
Hui Yu ◽  
Bingjie Lu ◽  
...  
Keyword(s):  
Negative Influence ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Eulaliopsis Binata ◽  
Different Types ◽  
Powder Samples ◽  
Xrd Patterns ◽  
Xrd Method

AbstractThe crystallinity indices (CrI) of Chinese handmade papers were investigated using the X-ray diffraction (XRD) method. Four Chinese handmade papers, Yingchun, Zhuma, Yuanshu and Longxucao papers were used as model substrates of mulberry bark, ramie, bamboo and Eulaliopsis binata papers, respectively. Two forms of the paper samples, paper sheets and their comminuted powders, were used in this study. The results showed that their XRD patterns belong to the cellulose-I type and Iβ dominates the cellulose microstructure of these paper samples. Moreover, it was found that the microstructures and CrIs of cellulose of these papers were changed by the grinding treatment. This work suggested that the sheet form of the handmade papers is suitable to determine CrI by XRD, despite the contribution of non-cellulosic components in the papers. The order of CrIs for these paper sheet samples was Yingchun, Zhuma, Longxucao and Yuanshu papers. Besides CrIs, differences in cross-sectional areas of the crystalline zone of cellulose can be used for comparing different types of handmade papers. It was also found that the CrIs and crystallite size of paper cellulose varied between the sheet samples and the powder samples, illustrating that the pulverisation has a negative influence on the microstructure of the handmade papers.

Effects of Different Sintering Temperature on the Microstructure and Piezoelectric Properties of Pb(Nb2/3Zn1/3)x(Zr52Ti48)1-XO3 Ceramics

2014 ◽  
Vol 1061-1062 ◽  
pp. 83-86
Author(s):  
Hong Wu ◽  
De Yi Zheng
Keyword(s):  
Electrical Properties ◽  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Sintering Temperature ◽  
Electromechanical Coupling Coefficient ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ceramic Samples ◽  
Xrd Patterns ◽  
The Relationship

In this paper, the effects of different sintering temperature on the microstructure and piezoelectric properties of Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3(PNZZT) ceramic samples were investigated. The Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3 ceramics materials was prepared by a conventional mixed oxide method. In the period of the experiment, the relationship between crystallographic phase and microstructure were analyzed by X-ray diffraction(XRD) and scanning electron microscopy(SEM) respectively. The XRD patterns shows that all of the ceramic samples are with a tetragonal perovskite structure. Along with sintering temperature increased and the x is 0.03, the grain size gradually become big. Through this experiment, it has been found that when the x is 0.03 and sintered at 1130°C for 2 h, the grains grow well, the grain-boundary intersection of the sample combined well and the porosity of the ceramics decreased, an excellent comprehensive electrical properties of the Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3 samples can be obtained. Its best electrical properties are as follows: dielectric constant (ε) is 1105, dielectric loss(tg) is 0.017, electromechanical coupling coefficient (Kp) is 0.287, piezoelectric constant(d33) is 150PC/N

Textures Applied to Mechanical Processing Technology Assessment in Ancient Bronze

2005 ◽  
Vol 495-497 ◽  
pp. 719-724
Author(s):  
R.E. Bolmaro ◽  
B. Molinas ◽  
E. Sentimenti ◽  
A.L. Fourty
Keyword(s):  
Orientation Distribution ◽  
Distribution Functions ◽  
Archaeological Sites ◽  
Mechanical Processing ◽  
Post Processing ◽  
X Ray Diffraction ◽  
Mechanical Process ◽  
X Ray ◽  
Pole Figures ◽  
Microscopic Inspection

Some ancient metallic art craft, utensils, silverware and weapons are externally undistinguishable from modern ones. Not only the general aspect and shape but also some uses have not changed through the ages. Moreover, when just some small pieces can be recovered from archaeological sites, the samples can not easily be ascribed to any known use and consequently identified. It is clear that mechanical processing has changed along history but frequently only a "microscopic" inspection can distinguish among different techniques. Some bronze samples have been collected from the Quarto d’Altino (Veneto) archaeological area in Italy (paleovenetian culture) and some model samples have been prepared by a modern artisan. The sample textures have been measured by X-ray Diffraction techniques. (111), (200) and (220) pole figures were used to calculate Orientation Distribution Functions and further recalculate pole figures and inverse pole figures. The results were compared with modern forging technology results. Textures are able to discern between hammering ancient techniques for sheet production and modern industrial rolling procedures. However, as it is demonstrated in the present work, forgery becomes difficult to detect if the goldsmith, properly warned, proceeds to erase the texture history with some hammering post-processing. The results of this contribution can offer to the archaeologists the opportunity to take into consideration the texture techniques in order to discuss the origin (culture) of the pieces and the characteristic mechanical process developed by the ancient artisan. Texture can also help the experts when discussing the originality of a certain piece keeping however in mind the cautions indicated in this publication.

Effect of Fly Ash and Slag on the Resistance to H2S Attack of Oil Well Cement

2009 ◽  
Vol 79-82 ◽  
pp. 71-74
Author(s):  
Qi Wang ◽  
Lin Qiao ◽  
Peng Song
Keyword(s):  
Fly Ash ◽  
Compression Strength ◽  
Blended Cement ◽  
Oil Well ◽  
X Ray Diffraction ◽  
X Ray ◽  
Curing Period ◽  
Oil Well Cement ◽  
Xrd Patterns ◽  
Well Cement

In this paper, the resistance to H2S attack of pastes made from slag-fly ash blended cement used in oil well (SFAOW) was studied, in which fly ash (FA) was used at replacement dosages of 30% to 60% by weight of slag. Samples of SCOW and SFAOW pastes were demoulded and cured by immersion in fresh water with 2 Mp H2S insulfflation under 130oC for 15 days. After this curing period, compression strength and permeability of the samples were investigated. The reaction mechanisms of H2S with the paste were carried out through a microstructure study, which included the use of x-ray diffraction (XRD) patterns and scanning electron microscope (SEM). Based on the obtained data in this study, incorporation of FA into SCOW results in the comparable effects in the resistance to H2S attack. When the replacement dosage of slag is about 40%, the paste exhibits the best performance on resistance to H2S attack with compression strength 36.58Mp.

STRUCTURE AND MAGNETIC PROPERTIES OF MECHANICAL ALLOYED Mn-15at.%Al

2013 ◽  
Vol 12 (01) ◽  
pp. 1350006
Author(s):  
AHMED E. HANNORA ◽  
FARIED F. HANNA ◽  
LOTFY K. MAREI
Keyword(s):  
Thermal Analysis ◽  
Room Temperature ◽  
Average Crystallite Size ◽  
Al Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Milled Sample ◽  
Powder Samples ◽  
Xrd Patterns ◽  
Method Analysis

Mechanical alloying (MA) method has been used to produce nanocrystallite Mn -15at.% Al alloy. X-ray diffraction (XRD) patterns for the as-milled elemental α- Mn and aluminum powder samples show a mixture of α + β- MnAl phases after 20 h of milling and changes to a dominant β- MnAl phase structure after 50 h. An average crystallite size of 40 nm was determined from Hall–Williamson method analysis after 5 h of milling. Moreover, the thermal analysis results using differential thermal analysis (DTA), suggested a possible phase transformation after 20 h of milling. Isothermal treatments are carried in the temperature range of 450°C to 1000°C. Room-temperature vibrating sample magnetometer (VSM) measurements of the hysteretic response revealed that the saturation magnetization Bs and coercivity Hc for 10 h ball milled sample are ~ 2.1 emu/g and ~ 92 Oe, respectively.

Effects of Indium Incorporation on the Optical Properties of ZnO Films

2006 ◽  
Vol 11-12 ◽  
pp. 159-162 ◽  
Author(s):  
Yong Ge Cao ◽  
Lei Miao ◽  
Sakae Tanemura ◽  
Yasuhiko Hayashi ◽  
Masaki Tanemura
Keyword(s):  
Optical Transmission ◽  
Full Width Half Maximum ◽  
Structural Disorder ◽  
Band Gaps ◽  
Zno Films ◽  
Photoluminescence Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optical Band Gaps ◽  
Xrd Patterns

Transparent indium-doped ZnO (IZO) films with low In content (<6at%) were fabricated through radio-frequency (rf) helicon magnetron sputtering. Formation of In-Zn-O solid solution was confirmed by X-ray diffraction (XRD) patterns. Incorporation of indium into ZnO films enhances the optical transmission in the visible wavelength. The optical band-gaps slightly increase from 3.25eV (ZnO) to 3.28eV (In0.04Zn0.96O) and to 3.30eV (In0.06Zn0.94O) due to Burstain-Moss effect. The Urbach tail parameter E0, which is believed to be a function of structural disorder, increases from 79meV (ZnO), to 146meV (In0.04Zn0.96O), and to 173meV (In0.06Zn0.94O), which is consistent with increase of Full-Width Half-Maximum (FWHM) in corresponding XRD patterns. Decreasing in crystal quality with increasing indium concentration is also confirmed by photoluminescence spectra.

scholarly journals FTIR and Optical Properties of NiO Doped Cr2O3 Nanopar-ticles Synthesis by Hydrothermal Method

2018 ◽  
Vol 29 (1) ◽  
pp. 168
Author(s):  
Tunis Balassim Hassan
Keyword(s):  
Optical Band Gap ◽  
Average Crystallite Size ◽  
Structural Behavior ◽  
X Ray Diffraction ◽  
Nanopar Ticles ◽  
Hydrothermal Technique ◽  
X Ray ◽  
Cr2o3 Nanoparticles ◽  
Xrd Patterns ◽  
Scanning Electron

Pure and Nickel oxide doped chromium (III) oxide (Cr2O3) nanoparticals are synthesized by hydrothermal technique. The effect of dopant Ni concentration on the structural behavior of Cr2O3 nanoparticles was examined by X-ray diffraction. The average crystallite size of the synthesized nanoparticles was measured from XRD patterns using Scherrer equation and was decreased from 22nm to 12.9 nm with the increasing Nio concentration in Cr2O3 from (0, 0.01, 0.06, and 0.10). Morphologies and compositional elements of the synthesized nanoparticles were observed by the field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopy, respectively. The optical property of the samples was measured by ultraviolet - visible (UV-Vis.) absorption spectroscopy. The observed optical band gap value ranges from 2.3eV to 2.5eV for Ni doped nanoparticles

Sign in / Sign up

Export Citation Format

Share Document