scholarly journals A Structural Based Thermal Model Description for Vertical SiC Power MOSFETs under Fault Conditions

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
Andreas Maerz ◽  
Teresa Bertelshofer ◽  
Mark-M. Bakran
Keyword(s):  
Boundary Conditions ◽  
Thermal Model ◽  
Short Circuit ◽  
Gate Oxide ◽  
Power Converter ◽  
Junction Temperature ◽  
Voltage Source ◽  
Model Description ◽  
General Description ◽  
Testing Procedures

The accurate prediction of the SiC MOSFET withstanding time for single fault events greatly influences the requirements for device protection circuits for these devices in power converter applications, like voltage source inverters or power electronic transformers. For this reason, a thermal model, based on the structural design and the physical dimensions of the chip as well as material properties of 4H-SiC, is proposed. This article gives a general description of the thermal behaviour of vertical SiC MOSFET under various driving and boundary conditions in case of a short-circuit event. The thermal model substitutes destructive tests of a device for an individual set of boundary conditions of an occurring fault event. The validity of the analytically parametrised thermal model is verified by experimental short-circuit tests of state-of-the-art vertical SiC MOSFETs for a set of various boundary conditions. The investigated thermal model can furthermore be used to standardise different gate-oxide degradation values from the literature for means of lifetime prediction of the gate oxide for an individual application under repetitive occurring fault or overload conditions. These manufacturer specific reported values measured with no standardised testing procedures can be translated into a maximum junction temperature, which is repeatedly reached. The thermal model therefore provides a unifying parameter for the gate-oxide lifetime calculation for an individual chip and application.

SABER-Based Simulation for Compact Dynamic Electro-Thermal Modeling Analysis of Power Electronic Devices

2011 ◽  
Vol 291-294 ◽  
pp. 1704-1708
Author(s):  
Ming Chen ◽  
An Hu ◽  
Yong Tang ◽  
Bo Wang
Keyword(s):  
Temperature Distribution ◽  
Network Model ◽  
Thermal Model ◽  
Electronic Devices ◽  
Power Converter ◽  
Junction Temperature ◽  
Power Electronic ◽  
Electrical Model ◽  
Thermal Component ◽  
Infrared Thermal Imaging

Power electronic modules including insulated gate bipolar transistor (IGBT) are widely used in the field of power converter application. The temperature distribution inside these modules becomes more important for electrical characteristics, reliability and lifetime of integrated power electronic modules. In this paper, a seven-layer compact RC thermal component network model based on the physical structure is presented. A dynamic electro-thermal model, which is composed of electrical model, compact RC thermal component network model and electro-thermal interface is developed for the IGBT. These models interact with each other to calculate the temperature of each layer of module and parameters of each model. The thermal model determines the evolution of the temperature distribution within the thermal network and thus determines the instantaneous junction temperature used by the electrical model. Such built dynamic electro-thermal simulation methodology is implemented in the Saber circuit simulator, and the simulation result is validated by the experimental study, which adopted with infrared thermal imaging camera. The built dynamic electro-thermal model could be helpful for the research on operation performance and heat sink design for such power electronic devices.

scholarly journals Intrinsic Self-Healing Epoxies in Polymer Matrix Composites (PMCs) for Aerospace Applications

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 201
Author(s):  
Stefano Paolillo ◽  
Ranjita K. Bose ◽  
Marianella Hernández Santana ◽  
Antonio M. Grande
Keyword(s):  
High Performance ◽  
Polymer Matrix Composites ◽  
Critical Issue ◽  
General Description ◽  
Self Healing ◽  
Matrix Composites ◽  
Testing Procedures ◽  
Aerospace Applications ◽  
Polymer Properties ◽  
Healing Efficiency

This article reviews some of the intrinsic self-healing epoxy materials that have been investigated throughout the course of the last twenty years. Emphasis is placed on those formulations suitable for the design of high-performance composites to be employed in the aerospace field. A brief introduction is given on the advantages of intrinsic self-healing polymers over extrinsic counterparts and of epoxies over other thermosetting systems. After a general description of the testing procedures adopted for the evaluation of the healing efficiency and the required features for a smooth implementation of such materials in the industry, different self-healing mechanisms, arising from either physical or chemical interactions, are detailed. The presented formulations are critically reviewed, comparing major strengths and weaknesses of their healing mechanisms, underlining the inherent structural polymer properties that may affect the healing phenomena. As many self-healing chemistries already provide the fundamental aspects for recyclability and reprocessability of thermosets, which have been historically thought as a critical issue, perspective trends of a circular economy for self-healing polymers are discussed along with their possible advances and challenges. This may open up the opportunity for a totally reconfigured landscape in composite manufacturing, with the net benefits of overall cost reduction and less waste. Some general drawbacks are also laid out along with some potential countermeasures to overcome or limit their impact. Finally, present and future applications in the aviation and space fields are portrayed.

scholarly journals A GaN-HEMT Compact Model Including Dynamic RDSon Effect for Power Electronics Converters

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2092
Author(s):  
Ke Li ◽  
Paul Leonard Evans ◽  
Christopher Mark Johnson ◽  
Arnaud Videt ◽  
Nadir Idir
Keyword(s):  
Power Electronics ◽  
Physical Model ◽  
Order Reduction ◽  
Power Converter ◽  
Compact Model ◽  
Voltage Source ◽  
Power Losses ◽  
Gan Hemt ◽  
Operation Conditions ◽  
Power Electronics Converters

In order to model GaN-HEMT switching transients and determine power losses, a compact model including dynamic RDSon effect is proposed herein. The model includes mathematical equations to represent device static and capacitance-voltage characteristics, and a behavioural voltage source, which includes multiple RC units to represent different time constants for trapping and detrapping effect from 100 ns to 100 s range. All the required parameters in the model can be obtained by fitting method using a datasheet or experimental characterisation results. The model is then implemented into our developed virtual prototyping software, where the device compact model is co-simulated with a parasitic inductance physical model to obtain the switching waveform. As model order reduction is applied in our software to resolve physical model, the device switching current and voltage waveform can be obtained in the range of minutes. By comparison with experimental measurements, the model is validated to accurately represent device switching transients as well as their spectrum in frequency domain until 100 MHz. In terms of dynamic RDSon value, the mismatch between the model and experimental results is within 10% under different power converter operation conditions in terms of switching frequencies and duty cycles, so designers can use this model to accurately obtain GaN-HEMT power losses due to trapping and detrapping effects for power electronics converters.

scholarly journals Surface Wave Speed of Functionally Graded Magneto-Electro-Elastic Materials with Initial Stresses

2014 ◽  
Vol 44 (3) ◽  
pp. 49-64 ◽  
Author(s):  
Li Li ◽  
P. J. Wei
Keyword(s):  
Surface Wave ◽  
Boundary Conditions ◽  
Elastic Material ◽  
Short Circuit ◽  
Equations Of Motion ◽  
Open Circuit ◽  
Functionally Graded ◽  
Initial Stresses ◽  
Shear Surface ◽  
Traction Boundary Conditions

Abstract The shear surface wave at the free traction surface of half- infinite functionally graded magneto-electro-elastic material with initial stress is investigated. The material parameters are assumed to vary ex- ponentially along the thickness direction, only. The velocity equations of shear surface wave are derived on the electrically or magnetically open circuit and short circuit boundary conditions, based on the equations of motion of the graded magneto-electro-elastic material with the initial stresses and the free traction boundary conditions. The dispersive curves are obtained numerically and the influences of the initial stresses and the material gradient index on the dispersive curves are discussed. The investigation provides a basis for the development of new functionally graded magneto-electro-elastic surface wave devices.

scholarly journals Modeling for Development of Simulation Tool: Impact of TCSC on Apparent Impedance Seen by Distance Relay

2018 ◽  
Vol 8 (5) ◽  
pp. 3332-3337
Author(s):  
N. M. Khoa ◽  
D. D. Tung
Keyword(s):  
Transmission Line ◽  
Power Transmission ◽  
Short Circuit ◽  
Simulation Software ◽  
Voltage Source ◽  
Power Transmission Line ◽  
Distance Protection ◽  
Protection Relay ◽  
The Impact ◽  
Distance Protection Relay

The impact of thyristor controlled series capacitor (TCSC) on distance protection relays in transmission lines is analyzed in this paper. Voltage and current data are measured and collected at the relay locations to calculate the apparent impedance seen by distance protection relays in the different operating modes of the TCSC connected to the line. Short-circuit faults which occur at different locations on the power transmission line are considered in order to locate the fault for the purpose of evaluating the impact of TCSC on the distance protection relay. Matlab/Simulink simulation software is used to model the power transmission line with two sources at the two ends. Voltage source, transmission line, TCSC, voltage and current measurement, and discrete Fourier transform (DFT) blocks are integrated into the model. Simulation results show the impact of TCSC on the distance protection relay and determine the apparent impedance and fault location in the line.

scholarly journals Feedback Loop Control Strategies of the Multi Dc Bus Link Voltages Using Adaptive Fuzzy Logic Control

2013 ◽  
Vol 64 (3) ◽  
pp. 143-151
Author(s):  
Farid Bouchafaa ◽  
Mohamed Seghir Boucherit ◽  
El Madjid Berkouk
Keyword(s):  
Fuzzy Logic ◽  
Fuzzy Logic Controller ◽  
Control Strategies ◽  
Harmonic Distortion ◽  
Power Converter ◽  
Voltage Source ◽  
Switching Frequency ◽  
Pwm Rectifier ◽  
Loop Control ◽  
Multilevel Inverters

Voltage source multilevel inverters have become very attractive for power industries in power electronics applications during last years. The main purposes that have led to the development of the studies about multilevel inverters are the generation of output voltage signals with low harmonic distortion; the reduction of switching frequency. A serious constraint in a multilevel inverter is the capacitor voltage-balancing problem. The unbalance of different DC voltage sources of five-level neutral point clamping (NPC) voltage source inverter (VSI) constitutes the major limitation for the use of this new power converter. In order to stabilize these DC voltages, we propose in this paper to study the cascade constituted by three phases five-level PWM rectifier, a clamping bridge and five-level NPC (VSI). In the first part, we present a topology of five-level NPC VSI, and then they propose a model of this converter and an optimal PWM strategy to control it using four bipolar carriers. Then in the second part, we study a five-level PWM rectifier, which is controlled by a multiband hysteresis strategy. In the last part of this paper, the authors study shows particularly the problem of the stability of the multi DC voltages of the inverter and its consequence on the performances of the induction motors (IM). Then, we propose a solution to the problem by employed closed loop regulation using PI regulator type fuzzy logic controller (FLC). The results obtained with this solution confirm the good performances of the proposed solution, and promise to use the inverter in high voltage and great power applications as electrical traction.

Sign in / Sign up

Export Citation Format

Share Document