scholarly journals Determination of Modelling Error Statistics for Cold-Formed Steel Columns

2020 ◽  
Vol 2020 ◽  
pp. 1-25 ◽  
Author(s):  
R. P. Rokade ◽  
K. Balaji Rao ◽  
B. Palani
Keyword(s):  
Failure Modes ◽  
International Standards ◽  
Research Centre ◽  
Distortional Buckling ◽  
Design Standards ◽  
Buckling Mode ◽  
Design Standard ◽  
Cold Formed Steel ◽  
Test Database ◽  
Modelling Error

In this article, an attempt has been made to estimate the Modelling Error (ME) associated with compression capacity models available in international standards for different failure modes of compression members fabricated from Cold-Formed Steel (CFS) lipped channel sections. For the first time, a database has been created using test results available in the literature for compression capacities of CFS lipped-channel sections. The database contains details of 273 numbers of compression member tests which have failed in different failure modes, namely, (i) flexural, torsional, flexural-torsional, local, and distortion buckling and (ii) failure by yielding. Only those sources, which report all the details, required to compute the capacities using different standards are included in the database. The results of experimental investigations carried out at CSIR-Structural Engineering Research Centre, Chennai, are also included in this test database. The international codes of practice used in calculation of compression capacities of the database columns considered in this paper are ASCE 10-15 (2015), AISI S100-16 (2016), AS/NZS 4600: 2018 (2018), and EN 1993-1-3:2006 (2006). The ASCE, AISI, AS/NZS, and EN design standards have different design guidelines with respect to the failure modes, e.g., ASCE 10-15 (2015) standard provides stringent criteria for maximum width to thickness ratio for stiffened and unstiffened elements. Hence, guidelines for the distortional buckling mode are not provided, whereas the AISI S100-16 (2016) and AS/NZS 4600: 2018 (2018) standards consider separate guidelines for distortional buckling mode and EN 1993-1-3:2006 (2006) standard considers combined local and distortional buckling mode. Further, the sample size for each design standard is varying depending on the design criteria and failure mode. Studies on statistical analysis of ME suggest that the compression capacity predicting models for flexural-torsional buckling mode are associated with large variation irrespective of the design standard. Similar observations are made for the flexural buckling model as per EN 1993-1-3:2006 (2018) standard and distortional buckling models as per AISI S100-16 (2016) and AS/NZS 4600: 2018 (2018) standards. The compression capacities for test database sections are evaluated by neglecting the partial safety factors available in design standards. The probabilistic analysis to determine statistical characteristics of compression capacity indicates the importance of consideration of ME as a random variable. Hence, the ME results will be useful in code calibration studies and may have potential reference to design practice.

C-section Cold-Formed Steel as Structural Members in Housing Construction in the Philippines

2019 ◽  
Author(s):  
Bernardo A. Lejano
Keyword(s):  
Axial Compression ◽  
High Speed ◽  
Failure Modes ◽  
Weight Ratio ◽  
High Strength ◽  
The Philippines ◽  
Bending Test ◽  
Housing Construction ◽  
Distortional Buckling ◽  
Cold Formed Steel

<p>Getting good lumber for housing construction is becoming difficult in the Philippines due to existing partial log ban. Although, the use of reinforced concrete is still the most popular in construction, an emerging alternative is the use of cold-formed steel (CFS). It is gaining popularity because of its high strength-to- weight ratio. However, information about the structural performance of locally-produced cold-formed steel is almost nonexistent. Although, design provisions are stipulated in the local Code, these are based on formulas developed abroad, hence the need to investigate these cold-formed steel. This study focuses on the C-section cold-formed steel, which is the most popularly used. The objective is to verify its performance when subjected to axial compression and flexure, both experimentally and computationally. For the computational part, the formulas stipulated in the National Structural Code of the Philippines were followed. For the experimental part, the cold-formed steel members were subjected to compression loads and flexural loads. Aside from usual sensors, high-speed cameras were used to capture the failure modes. For axial compression test, 80 specimens with different lengths and thicknesses were tested. For flexure, 24 specimens of back-to-back C-sections were subjected to 4-point bending test. Results showed the predicted strengths were well below the experimental values. In design, this means the use of Code-based formulas is conservative. Failure modes observed were torsional buckling and distortional buckling. Comparison of failure modes between experiment and computation shows 70% agreement for compression and 75% for flexure. Finite element method calculations were also done and were compared with experimental results.</p>

Lipped channel cold-formed steel columns under local-distortional buckling mode interaction

2019 ◽  
Vol 137 ◽  
pp. 251-270 ◽  
Author(s):  
Gustavo Y. Matsubara ◽  
Eduardo de M. Batista ◽  
Guilherme C. Salles
Keyword(s):  
Mode Interaction ◽  
Distortional Buckling ◽  
Buckling Mode ◽  
Steel Columns ◽  
Cold Formed Steel

Analysis of Cold-Formed Steel Lipped Channel Columns with Complex Edge Stiffeners and Web Holes

2013 ◽  
Vol 405-408 ◽  
pp. 664-667
Author(s):  
Chun Gang Wang ◽  
Yu Fei Cao ◽  
Lian Guang Jia ◽  
Hong Liu
Keyword(s):  
Finite Element Analysis ◽  
Failure Modes ◽  
Ultimate Load ◽  
Width Ratio ◽  
Distortional Buckling ◽  
Element Analysis ◽  
Stress Changes ◽  
Cold Formed Steel ◽  
The Web ◽  
Steel Section

This paper presents finite element analysis on cold-formed steel-section columns with complex edge stiffeners and web holes under axial compression. A total of 18 channel models with different parameters such as length, thickness and flange width are simulated. Failure modes, the ultimate load and the stress distribution around web holes are researched. The analysis results show that, the main failure mode of-section columns with complex edge stiffeners and web holes is distortional buckling. The carrying efficiency is higher as the thickness-width ratio increasing. Because of perforations on the web, the position of the max stress changes from the web near the mid-height of the specimens to the location adjacent to holes.

Experiments on Cold-Formed Steel Lipped Channel Beams with Complex Edge Stiffeners and Web Holes

2013 ◽  
Vol 671-674 ◽  
pp. 461-464
Author(s):  
Chun Gang Wang ◽  
Run Jia Liang ◽  
Lian Guang Jia ◽  
Hong Liu
Keyword(s):  
Bending Strength ◽  
Great Influence ◽  
Local Buckling ◽  
Experimental Results ◽  
Distortional Buckling ◽  
Buckling Mode ◽  
Element Analysis ◽  
Web Stiffeners ◽  
Cold Formed Steel ◽  
And Behavior

This paper presents an experimental investigation and a numerical analysis on the bending strength and behavior of cold-formed steel C-section and ∑-section beams with complex edge stiffeners and web holes. Local buckling, distortional buckling and interaction between local and distortional buckling were observed in the tests. The experimental results show that the stiffened web has great influence on member's bending strength. Compared with C-section specimens, the stiffness of the web stiffeners of ∑-section specimens reduced the influence of the holes. The finite element analysis results show good agreement with the experimental results in terms of bending strength and buckling mode.

Experimental Investigation of the Deformation of Built-up Members of Cold-Formed Steel Profiles

2011 ◽  
Vol 70 ◽  
pp. 416-421 ◽  
Author(s):  
Iveta Georgieva ◽  
Luc Schueremans ◽  
Guido De Roeck ◽  
Lincy Pyl
Keyword(s):  
Cross Section ◽  
Local Buckling ◽  
Element Model ◽  
Mode Shapes ◽  
European Standard ◽  
Distortional Buckling ◽  
Buckling Mode ◽  
Measuring Device ◽  
Measuring Techniques ◽  
Cold Formed Steel

Built-up members of cold-formed steel (CFS) profiles were tested in 4-point bending. CFS profiles (generally thin-walled) deform considerably under load, and the deformed configuration is a result of the superposition of different buckling mode shapes. Local buckling propagates through the profile walls; during distortional buckling parts of the cross-section rotate around a web-flange juncture. Alongside the buckling effects, the overall deformation of the member is considerable. To study these slender and relatively long members, a sufficient number of measuring positions on the specimens is needed. Often, this is not feasible with the conventional measuring techniques. An optical measuring device was used to record the movement of a large number of points per specimen. The obtained results are placed in a 3D coordinate system and can be exported for further data processing. The goal of the measurement campaign was to calibrate a Finite Element model that will simulate the tests. The model will be used for the analysis of composed frame members of CFS profiles, whose design is not entirely covered by the European Standard [1]. After calibration, the FEA predicts the performance of these built-up members well.

scholarly journals Calculation of Critical Load for Pure Distortional Buckling of Lipped Channel Columns

2019 ◽  
Author(s):  
Imene Mahi ◽  
Mohamed Djelil ◽  
Naoual Djafour ◽  
Mustapha Djafour
Keyword(s):  
Width Ratio ◽  
Distortional Buckling ◽  
Design Standards ◽  
Buckling Mode ◽  
Finite Strip ◽  
Strip Method ◽  
Codes Of Practice ◽  
Finite Strip Method ◽  
Buckling Stress ◽  
European Method

This paper presents a method that allows calculating the elastic critical stress for the distortional buckling mode, based on the buckling mode classification of typical lipped channel columns. In our case, Cold-Formed Steel Lipped Channel Columns are subjected to compression. Moreover, in order to consolidate the important findings of this work, a comparative study was carried out to assess the reliability of various distortional buckling models that are provided by different design Standards. It was found that the American and Australian approaches, given in the codes of practice, are closer to the Finite Strip Method than to the European method. An analytical solution was proposed for the determination of the distortional buckling stress on the basis of a statistical method; it corresponds to lipped channel sections with a flange width to web width ratio b/h ranging from 0.1 to 1, and a lip width to web width ratio c/h between 0 and 0.5. After comparison with the results given by the finite strip method for pure distortional buckling, it turned out that the proposed approach provides a reasonable prediction for the elastic distortional buckling stress for lipped channel sections subjected to compression. In fact, this method gives better results than the American approach.

Cold-formed steel battened built-up columns: Experimental behaviour and verification of different design rules developed

2021 ◽  
pp. 136943322110480
Author(s):  
A.R. Dar ◽  
S. Vijayanand ◽  
M. Anbarasu ◽  
M. Adil Dar
Keyword(s):  
Failure Modes ◽  
Numerical Models ◽  
Experimental Studies ◽  
Design Standards ◽  
Uniform Compression ◽  
Design Rules ◽  
The North ◽  
Current Design ◽  
Cold Formed Steel ◽  
In The Beginning

Some of the past studies on cold-formed steel (CFS) battened built-up columns have resulted in the development of new design rules for predicting their axial strengths. However, the main drawbacks of such studies are that they are purely numerical and the numerical models developed for such parametric studies were validated using the test results on similar built-up column configurations, but not the exact ones. Therefore, experimental studies on CFS battened columns comprising of lipped channels are needed for verifying the accuracy of the proposed design rules for CFS battened columns. This paper reports an experimental study performed on CFS built-up battened columns under axial compression. Adequately spaced identical lipped channels in the back-to-back arrangement were used as chords and were connected by batten plates laterally with self-driving screws to form the built-up members. The dimensions of chords were fixed as per the geometric limits given out in the North American Specifications (NAS) for the design of CFS structural members. The sectional compactness of the chords and the overall slenderness of the built-up columns were varied by altering the thickness of the channels and height of the built-up columns, respectively. A total of 20 built-up sections were tested under uniform compression to investigate the behavioural changes in the built-up columns due to these variations. The behaviour assessment was made in terms of peak strengths, load–displacement response and failure modes of the test specimens. The current design standards on CFS structures were used to determine the design strengths and were compared against the test strengths for assessing their adequacy. Furthermore, as discussed in the beginning, the test strengths were used to verify the accuracy of the different relevant proposed design rules in the literature.

scholarly journals Constrained Finite Strip Method with Rigid Corner Element for the Buckling Analysis of Thin-Walled Members with Rounded Corners

2019 ◽  
Author(s):  
Zoltán Beregszászi ◽  
Sándor Ádány
Keyword(s):  
Buckling Analysis ◽  
Structural Members ◽  
Distortional Buckling ◽  
Modal Decomposition ◽  
Buckling Mode ◽  
Finite Strip ◽  
Strip Method ◽  
Finite Strip Method ◽  
Cold Formed Steel ◽  
Thin Walled

In this paper modal decomposition of the deformations of thin-walled structural members are discussed. Modal decomposition is a process which separates the characteristic behavior modes. If applied in buckling analysis, modal decomposition makes it possible to analyze pure global or pure distortional buckling or pure local-plate buckling. Ability to calculate critical loads to a pure buckling mode is highly useful in the design of thin-walled structural members, such as cold-formed steel beams or columns. Cold-formed steel profiles are always produced with rounded corners, and earlier studies showed that the now-used modal decomposition techniques of the constrained finite element method and generalized beam theory fail to lead to reasonable results if the rounded corners are directly modelled in the analysis. An extension to the constrained finite strip method is proposed and discussed. The proposal introduces rigid corner elements, which make it possible to perform the modal decomposition by the same process used for members with sharp corners, even if the rounded corners are directly modelled. The formulation of the proposal is summarized, then the rigid-corner approach is studied by an extended parametric study.

Sign in / Sign up

Export Citation Format

Share Document