scholarly journals Research on Impact Stress Transfer Characteristics of Lunar Rock Coring Drill

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Peng Li ◽  
Yizhuo Wang ◽  
Bo Xu ◽  
Junwei Liu ◽  
Weiwei Zhang
Keyword(s):  
Impact Energy ◽  
Lunar Surface ◽  
Cutting Edge ◽  
Design Parameters ◽  
Drill Bit ◽  
Drilling Tool ◽  
Drill Stem ◽  
Impact Stress ◽  
Transfer Characteristics ◽  
The Impact

In the whole lunar surface drilling and sampling task, it is critical to make the operation of the drilling and sampling impact system efficient and reliable. This paper focuses on how to improve the impact stress obtained at the cutting edge of the drill bit. Firstly, with the objective of maximizing the output impact energy, the design parameters of the percussive mechanism are optimally selected; based on the one-dimensional stress wave transfer theory, the collision input model and transfer models of impact stress in the drilling tool are established. Secondly, in order to verify the above design parameters and theoretical models, the percussive drive characteristics’ test and the transfer characteristics’ tests of impact stress in the drill stem and drilling tool joints are carried out in turn. The experimental results are consistent with the theoretical analysis, which clarifies the transfer characteristics of the impact stress at the various stages of generation, incidence, and transfer to the cutting edge. It was finally found that increasing the percussive frequency and impact energy of the percussive mechanism as well as the contact stiffness of the collision surface can increase the incident impact stress of the drilling tool, while reducing the length of the screw connection between the drill bit and the drill stem can reduce the impact stress loss. This provides a theoretical reference for the design of the percussive mechanism and drilling tools in lunar surface drilling and sampling tasks.

scholarly journals Prediction Model of Drilling Performance for Percussive Rock Drilling Tool

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Dae-Ji Kim ◽  
Jaewon Kim ◽  
Booyeong Lee ◽  
Min-Seok Shin ◽  
Joo-Young Oh ◽  
...  
Keyword(s):  
Prediction Model ◽  
Dynamic Effect ◽  
Drill Bit ◽  
Motion Model ◽  
Percussive Drilling ◽  
Drilling Tool ◽  
Rock Types ◽  
Drilling Performance ◽  
The Impact

This study suggests a method for quantitatively estimating the drilling performance of the down-the-hole (DTH) hammer during percussive drilling of rock surfaces. A pneumatic dynamic model of the DTH hammer was developed that considers the mass flow rate relations representing the orifice opening areas of the air tube, the piston, and bit flushing channels. A drill bit motion model was developed to represent the dynamics of a drill bit impacted by a dropped piston and explain the impact stress propagation and rock-crushing mechanism. The rock-crushing effect of the drill button bit was measured through a piston drop test. The pneumatic hammer model and drill bit motion model were then combined in a prediction model to determine the impact efficiency according to different rock types (i.e., soft, medium-hard, and very hard). The drilling efficiency was defined as the input value of the prediction model, which was used to simulate the drilling performance of DTH hammers considering the rock type and dynamic effect of the drill bit. Finally, the simulation results were compared with the results of in situ drilling tests for verification.

Dynamics of Single-Hit Pneumatic Test Drill for Pulse-Shaping Analysis of Impacting Waves

2013 ◽  
Author(s):  
Jori Montonen ◽  
Erno Keskinen ◽  
Michel Cotsaftis ◽  
Juha Miettinen ◽  
Wolfgang Seeman
Keyword(s):  
Penetration Depth ◽  
Impact Energy ◽  
Pulse Shape ◽  
Model Updating ◽  
Blast Hole ◽  
Initial Pressure ◽  
Design Parameters ◽  
Drilling Process ◽  
Rod System ◽  
The Impact

Rock drilling is one of the elementary processes in mining industry. As larger diameter holes are drilled by hitting with units attached to the crone adapter down in the hole, the smaller blast holes are hit with units impacting the rod neck at rock surface. Key question in the performance and energy efficiency of the blast-hole drilling process is then, how completely the impact energy can be transmitted to the crone over the relatively long wave guide. There have been discussions about the effect of wave length and shape on to the penetration dynamics of rock drills. As the drilling process is a continuous set of hits following each other at relatively high constant period and the response is a random overlapped mixture of coming waves and returning reflected waves from multiple delayed hits, a detailed analysis of penetration dynamics is rather a complex problem. To overcome this difficulty, a full-scale half-manual test-drill has been designed and built to produce single hits for a systematic production and analysis of optimally shaped stress waves. The test-drill is an air-powered pneumatic gun, whose impact energy can be adjusted by setting the initial pressure level to correspond the desired end velocity of the piston. The design parameters, by which the pulse shape can be modified, are the length and the geometric profile of the piston body. The first problem to be faced is then to determine the optimal pulse shape for maximized penetration depth and the second one is to produce such desired shape by an optimal choice of the design parameters. The rig has been modelled using finite elements for the rod system and adiabatic state equations for the compressed and expanding air volumes. By modifying the design parameters, different penetration responses can be produced. In the first step, the model has been updated by means of experimental response measurements. The second step has been to modify the geometrical profiles of the piston body by starting from piece-vice linear and parabolic cross-sectional distributions. The output of the numerical analysis is to evaluate the penetration depth pro hit for different geometrical profiles. The most promising geometry has then been selected for the fabrication of the prototype piston. An experimental hitting test then completes the analysis, whose repeatability showed to be limited due to the random variation of the rock properties in the test bed. Test results obtained by using more regular concrete specimens exhibited reduced deviations in the responses, but the weakness in the test is the different damaging mechanism during the penetration. Another option is the use of an artificial load-sensing endsupport in order to produce a known boundary condition to replace the tool-rock resistance in the model-updating phase.

scholarly journals Experimental and numerical study of drill bit drop tests on Kuru granite

2017 ◽  
Vol 375 (2085) ◽  
pp. 20160176 ◽  
Author(s):  
Marion Fourmeau ◽  
Alexandre Kane ◽  
Mikko Hokka
Keyword(s):  
Impact Energy ◽  
Numerical Study ◽  
Experimental Testing ◽  
Drop Test ◽  
Surface Shape ◽  
Test Machine ◽  
Drill Bit ◽  
Rock Interaction ◽  
Drop Tests ◽  
The Impact

This paper presents an experimental and numerical study of Kuru grey granite impacted with a seven-buttons drill bit mounted on an instrumented drop test machine. The force versus displacement curves during the impact, so-called bit–rock interaction (BRI) curves, were obtained using strain gauge measurements for two levels of impact energy. Moreover, the volume of removed rock after each drop test was evaluated by stereo-lithography (three-dimensional surface reconstruction). A modified version of the Holmquist–Johnson–Cook (MHJC) material model was calibrated using Kuru granite test results available from the literature. Numerical simulations of the single drop tests were carried out using the MHJC model available in the LS-DYNA explicit finite-element solver. The influence of the impact energy and additional confining pressure on the BRI curves and the volume of the removed rock is discussed. In addition, the influence of the rock surface shape before impact was evaluated using two different mesh geometries: a flat surface and a hyperbolic surface. The experimental and numerical results are compared and discussed in terms of drilling efficiency through the mechanical specific energy. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’.

The Geosciences Applied to Lunar Exploration

1962 ◽  
Vol 14 ◽  
pp. 169-257 ◽  
Author(s):  
J. Green
Keyword(s):  
Lunar Surface ◽  
Probable Mechanism ◽  
Point Of View ◽  
Lunar Exploration ◽  
Geological Model ◽  
Apply Geophysics ◽  
Surface Features ◽  
The Impact

The term geo-sciences has been used here to include the disciplines geology, geophysics and geochemistry. However, in order to apply geophysics and geochemistry effectively one must begin with a geological model. Therefore, the science of geology should be used as the basis for lunar exploration. From an astronomical point of view, a lunar terrain heavily impacted with meteors appears the more reasonable; although from a geological standpoint, volcanism seems the more probable mechanism. A surface liberally marked with volcanic features has been advocated by such geologists as Bülow, Dana, Suess, von Wolff, Shaler, Spurr, and Kuno. In this paper, both the impact and volcanic hypotheses are considered in the application of the geo-sciences to manned lunar exploration. However, more emphasis is placed on the volcanic, or more correctly the defluidization, hypothesis to account for lunar surface features.

scholarly journals Kinematics and dynamics analysis of new rotary-percussive PDM drilling tool

2021 ◽  
pp. 146134842198915
Author(s):  
Jialin Tian ◽  
Xuehua Hu ◽  
Liming Dai ◽  
Lin Yang ◽  
Yi Yang ◽  
...  
Keyword(s):  
Drill String ◽  
Structure Design ◽  
Drilling Process ◽  
Analysis Model ◽  
Drilling Tool ◽  
Stick Slip ◽  
Rate Of Penetration ◽  
Bottom Hole ◽  
Bottom Hole Assembly ◽  
The Impact

This paper presents a new drilling tool with multidirectional and controllable vibrations for enhancing the drilling rate of penetration and reducing the wellbore friction in complex well structure. Based on the structure design, the working mechanism is analyzed in downhole conditions. Then, combined with the impact theory and the drilling process, the theoretical models including the various impact forces are established. Also, to study the downhole performance, the bottom hole assembly dynamics characteristics in new condition are discussed. Moreover, to study the influence of key parameters on the impact force, the parabolic effect of the tool and the rebound of the drill string were considered, and the kinematics and mechanical properties of the new tool under working conditions were calculated. For the importance of the roller as a vibration generator, the displacement trajectory of the roller under different rotating speed and weight on bit was compared and analyzed. The reliable and accuracy of the theoretical model were verified by comparing the calculation results and experimental test results. The results show that the new design can produce a continuous and stable periodic impact. By adjusting the design parameter matching to the working condition, the bottom hole assembly with the new tool can improve the rate of penetration and reduce the wellbore friction or drilling stick-slip with benign vibration. The analysis model can also be used for a similar method or design just by changing the relative parameters. The research and results can provide references for enhancing drilling efficiency and safe production.

Design of a Robust Memristive Spiking Neuromorphic System with Unsupervised Learning in Hardware

2021 ◽  
Vol 17 (4) ◽  
pp. 1-26
Author(s):  
Md Musabbir Adnan ◽  
Sagarvarma Sayyaparaju ◽  
Samuel D. Brown ◽  
Mst Shamim Ara Shawkat ◽  
Catherine D. Schuman ◽  
...  
Keyword(s):  
Unsupervised Learning ◽  
Recognition Task ◽  
Single Layer ◽  
Process Variations ◽  
Spike Timing ◽  
System Level ◽  
Design Parameters ◽  
Digital Pulse ◽  
Neuromorphic System ◽  
The Impact

Spiking neural networks (SNN) offer a power efficient, biologically plausible learning paradigm by encoding information into spikes. The discovery of the memristor has accelerated the progress of spiking neuromorphic systems, as the intrinsic plasticity of the device makes it an ideal candidate to mimic a biological synapse. Despite providing a nanoscale form factor, non-volatility, and low-power operation, memristors suffer from device-level non-idealities, which impact system-level performance. To address these issues, this article presents a memristive crossbar-based neuromorphic system using unsupervised learning with twin-memristor synapses, fully digital pulse width modulated spike-timing-dependent plasticity, and homeostasis neurons. The implemented single-layer SNN was applied to a pattern-recognition task of classifying handwritten-digits. The performance of the system was analyzed by varying design parameters such as number of training epochs, neurons, and capacitors. Furthermore, the impact of memristor device non-idealities, such as device-switching mismatch, aging, failure, and process variations, were investigated and the resilience of the proposed system was demonstrated.

Making Up 3D Bodies

2021 ◽  
Vol 4 (2) ◽  
pp. 1-9
Author(s):  
Kiona Hagen Niehaus ◽  
Rebecca Fiebrink
Keyword(s):  
Software Tool ◽  
The Body ◽  
Design Parameters ◽  
Artistic Practice ◽  
Human Form ◽  
Modeling Systems ◽  
Exploratory Approach ◽  
Disability Status ◽  
High Level ◽  
The Impact

This paper describes the process of developing a software tool for digital artistic exploration of 3D human figures. Previously available software for modeling mesh-based 3D human figures restricts user output based on normative assumptions about the form that a body might take, particularly in terms of gender, race, and disability status, which are reinforced by ubiquitous use of range-limited sliders mapped to singular high-level design parameters. CreatorCustom, the software prototype created during this research, is designed to foreground an exploratory approach to modeling 3D human bodies, treating the digital body as a sculptural landscape rather than a presupposed form for rote technical representation. Building on prior research into serendipity in Human-Computer Interaction and 3D modeling systems for users at various levels of proficiency, among other areas, this research comprises two qualitative studies and investigation of the impact on the first author's artistic practice. Study 1 uses interviews and practice sessions to explore the practices of six queer artists working with the body and the language, materials, and actions they use in their practice; these then informed the design of the software tool. Study 2 investigates the usability, creativity support, and bodily implications of the software when used by thirteen artists in a workshop. These studies reveal the importance of exploration and unexpectedness in artistic practice, and a desire for experimental digital approaches to the human form.

scholarly journals Simulation Tests of a Cow Milking Machine—Analysis of Design Parameters

Processes ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 1358
Author(s):  
Ewa Golisz ◽  
Adam Kupczyk ◽  
Maria Majkowska ◽  
Jędrzej Trajer
Keyword(s):  
Mathematical Model ◽  
Simplified Model ◽  
Design Parameters ◽  
Degree Polynomial ◽  
Fourth Degree ◽  
Local Loss ◽  
Linear Drag ◽  
Milking Machine ◽  
Machine Analysis ◽  
The Impact

The objective of this paper was to create a mathematical model of vacuum drops in a form that enables the testing of the impact of design parameters of a milking cluster on the values of vacuum drops in the claw. Simulation tests of the milking cluster were conducted, with the use of a simplified model of vacuum drops in the form of a fourth-degree polynomial. Sensitivity analysis and a simulation of a model with a simplified structure of vacuum drops in the claw were carried out. As a result, the impact of the milking machine’s design parameters on the milking process could be analysed. The results showed that a change in the local loss and linear drag coefficient in the long milk duct will have a lower impact on vacuum drops if a smaller flux of inlet air, a higher head of the air/liquid mix, and a higher diameter of the long milk tube are used.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

scholarly journals Impact resistance of steel materials to ballistic ejecta and shelter development using steel deck plates

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Kohei Tateyama ◽  
Shino Naruke ◽  
Hisashi Sasaki ◽  
Shinichi Torigata ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Test ◽  
Impact Resistance ◽  
Protective Layer ◽  
High Strength ◽  
Steel Plates ◽  
Corrugated Plates ◽  
Shelter Construction ◽  
The Impact ◽  
Ballistic Ejecta

AbstractThe destruction caused by ballistic ejecta from the phreatic eruptions of Mt. Ontake in 2014 and Mt. Kusatsu-Shirane (Mt. Moto-Shirane) in 2018 in Japan, which resulted in numerous casualties, highlighted the need for better evacuation facilities. In response, some mountain huts were reinforced with aramid fabric to convert them into shelters. However, a number of decisions must be made when working to increase the number of shelters, which depend on the location where they are to be built. In this study, we propose a method of using high-strength steel to reinforce wooden buildings for use as shelters. More specifically, assuming that ballistic ejecta has an impact energy of 9 kJ or more, as in previous studies, we developed a method that utilizes SUS304 and SS400 unprocessed steel plates based on existing impact test data. We found that SUS304 is particularly suitable for use as a reinforcing material because it has excellent impact energy absorption characteristics due to its high ductility as well as excellent corrosion resistance. With the aim of increasing the structural strength of steel shelters, we also conducted an impact test on a shelter fabricated from SS400 deck plates (i.e., steel with improved flexural strength provided by work-hardened trapezoidal corrugated plates). The results show that the shelter could withstand impact with an energy of 13.5 kJ (2.66 kg of simulated ballistic ejecta at 101 m/s on impact). In addition, from the result of the impact test using the roof-simulating structure, it was confirmed the impact absorption energy is further increased when artificial pumice as an additional protective layer is installed on this structure. Observations of the shelter after the impact test show that there is still some allowance for deformation caused by projectile impact, which means that the proposed steel shelter holds promise, not only structurally, but also from the aspects of transportation and assembly. Hence, the usefulness of shelters that use steel was shown experimentally. However, shelter construction should be suitable for the target environment.

Sign in / Sign up

Export Citation Format

Share Document