scholarly journals Vibration harvesting integrated into vehicle suspension and bodywork

2021 ◽  
Vol 23 (1) ◽  
pp. 188
Author(s):  
Souad Touairi ◽  
Mustapha Mabrouki
Keyword(s):  
Finite Element ◽  
Piezoelectric Transducer ◽  
Ride Comfort ◽  
Vehicle Suspension ◽  
Ansys Software ◽  
Road Surfaces ◽  
Modelling Techniques ◽  
Simulation Results ◽  
Power Recovery ◽  
Piezoelectric Harvester

This work proposes a new piezoelectric transducer system with four freedoms of movement modelled and evaluated by mechatronic techniques. The proposed modelling techniques (finite element and bond graph) were performed in a 20-Sim framework attached to the ANSYS software. The established harvester system has the ability to increase the driver's comfort when travelling on several types of road surfaces. The piezoelectric harvester is designed to investigate and provide the health requirement and ride comfort of the vehicle's drives on random road surfaces. The simulation results affirm that the improved piezoelectric transducer arrangement is more productive for various aspects. The power recovery is significantly enhanced as well as the driving comfort on the three road categories. Finally, the harvestable power amount is highlighted and is graphically discussed for several specific applications.

Numerical Simulation of Temperature for Al2O3 Ceramics during Micro-Detonation of Arc Strike Machining

2012 ◽  
Vol 429 ◽  
pp. 3-8
Author(s):  
Xin Li Tian ◽  
Ke Ling Lin ◽  
Bao Guo Zhang ◽  
Chun Fang Xue ◽  
Jian Quan Wang
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
High Temperature ◽  
Theoretical Model ◽  
Pulse Width ◽  
Processing Parameters ◽  
Ansys Software ◽  
Temperature Zone ◽  
Simulation Results ◽  
Element Theory

A theoretical model of temperature for Al2O3ceramics during micro-detonation of arc strike machining was established. Based on finite element theory, the temperature of Al2O3ceramics during micro-detonation of arc strike machining was simulated with the aid of Ansys software, combined with the actual processing, the width and depth of cavity impacted by micro-detonation were calculated. The simulation results show that the highest temperature of Al2O3ceramics is over 13435 °C in a given processing parameters, while the high-temperature zone is quite small. With the increase of pulse width and electricity, the temperature within the machined zone increases rapidly, but the outside area kept a low temperature; and with the increase of nozzle radius, the diameter to depth ratio of the distribution of temperature is increasing gradually. The data gained from the simulation is proved to be accordant with the data gained from experiments.

Simulation on Anode Electric Field Intensity about Electrochemical Jet Machining

2011 ◽  
Vol 418-420 ◽  
pp. 2046-2049
Author(s):  
Cheng Guang Zhang ◽  
Fei Hu Zhang ◽  
Yong Zhang
Keyword(s):  
Finite Element ◽  
Electric Field ◽  
Uniform Distribution ◽  
Field Intensity ◽  
Electric Field Intensity ◽  
Distribution Area ◽  
Ansys Software ◽  
Close Relationship ◽  
Jet Nozzle ◽  
Simulation Results

The theory of electrochemical jet machining was introduced, and effect of different parameters on anodic electric field intensity is finite element analyzed by ANSYS software. The Simulation results show that, the electric field shares the same distribution under different electrolysis voltage, which generally contains three parts, uniform distribution area, gradually weakened area, scattered area. In the uniform distribution area, electric field shows comparative uniformity. The anode electric field generated by different jet distance is also obvious distribution areas, the electric field intensity shows decreasing trend. Electric field intensity is found to have a close relationship with electro jet nozzle diameter, in which a faster jet velocity would bring more concentrated distribution of the electric field as well as a smaller size of electric field.

Tire Vibration Modes and Effects on Vehicle Ride Quality

1993 ◽  
Vol 21 (1) ◽  
pp. 23-39 ◽  
Author(s):  
R. W. Scavuzzo ◽  
T. R. Richards ◽  
L. T. Charek
Keyword(s):  
Finite Element ◽  
Finite Element Modeling ◽  
Operating Conditions ◽  
Modal Testing ◽  
Ride Quality ◽  
Vibration Modes ◽  
Inflation Pressure ◽  
Passenger Cars ◽  
Element Modeling ◽  
Road Surfaces

Abstract Tire vibration modes are known to play a key role in vehicle ride, for applications ranging from passenger cars to earthmover equipment. Inputs to the tire such as discrete impacts (harshness), rough road surfaces, tire nonuniformities, and tread patterns can potentially excite tire vibration modes. Many parameters affect the frequency of tire vibration modes: tire size, tire construction, inflation pressure, and operating conditions such as speed, load, and temperature. This paper discusses the influence of these parameters on tire vibration modes and describes how these tire modes influence vehicle ride quality. Results from both finite element modeling and modal testing are discussed.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

scholarly journals Simulation and Nonlinearity Optimization of a High-Pressure Sensor

Sensors ◽  
2020 ◽  
Vol 20 (16) ◽  
pp. 4419
Author(s):  
Ting Li ◽  
Haiping Shang ◽  
Weibing Wang
Keyword(s):  
High Pressure ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
Original Model ◽  
Ansys Software ◽  
Nonlinear Error ◽  
Sensor Model ◽  
Optimized Model ◽  
Simulation Results ◽  
Better Than

A pressure sensor in the range of 0–120 MPa with a square diaphragm was designed and fabricated, which was isolated by the oil-filled package. The nonlinearity of the device without circuit compensation is better than 0.4%, and the accuracy is 0.43%. This sensor model was simulated by ANSYS software. Based on this model, we simulated the output voltage and nonlinearity when piezoresistors locations change. The simulation results showed that as the stress of the longitudinal resistor (RL) was increased compared to the transverse resistor (RT), the nonlinear error of the pressure sensor would first decrease to about 0 and then increase. The theoretical calculation and mathematical fitting were given to this phenomenon. Based on this discovery, a method for optimizing the nonlinearity of high-pressure sensors while ensuring the maximum sensitivity was proposed. In the simulation, the output of the optimized model had a significant improvement over the original model, and the nonlinear error significantly decreased from 0.106% to 0.0000713%.

Based on ANSYS Planetary Gear Ransmission Design Analysis

2011 ◽  
Vol 314-316 ◽  
pp. 1218-1221
Author(s):  
Hao Min Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Planetary Gear ◽  
Design Analysis ◽  
Ansys Software ◽  
Element Analysis ◽  
Planet Gear ◽  
Gear Contact ◽  
Transmission Gear

Conventional methods of design to be completed ordinary hydraulic transmission gear gearbox design, but for such a non-planet-rule entity, and the deformation of the planet-gear contact stress will have a great impact on the planet gear, it will be very difficult According to conventional design. In this paper, ANSYS software to the situation finite element analysis, the planetary gear to simulate modeling study.

Experimental and numerical studies on failure and energy absorption of composite thin-walled square tubes under quasi-static compression loading

2020 ◽  
Vol 21 (6) ◽  
pp. 623-634
Author(s):  
Haolei Mou ◽  
Zhenyu Feng ◽  
Jiang Xie ◽  
Jun Zou ◽  
Kun Zhou
Keyword(s):  
Finite Element ◽  
Shell Model ◽  
Energy Absorption ◽  
Failure Mode ◽  
Failure Criterion ◽  
Finite Element Models ◽  
Static Compression ◽  
Compression Loading ◽  
Thin Walled ◽  
Simulation Results

AbstractTo analysis the failure and energy absorption of carbon fiber reinforced polymer (CFRP) thin-walled square tube, the quasi-static axial compression loading tests are conducted for [±45]3s square tube, and the square tube after test is scanned to further investigate the failure mechanism. Three different finite element models, i.e. single-layer shell model, multi-layer shell model and stacked shell mode, are developed by using the Puck 2000 matrix failure criterion and Yamada Sun fiber failure criterion, and three models are verified and compared according to the experimental energy absorption metrics. The experimental and simulation results show that the failure mode of [±45]3s square tube is the local buckling failure mode, and the energy are absorbed mainly by intralaminar and interlaminar delamination, fiber elastic deformation, fiber debonding and fracture, matrix deformation cracking and longitudinal crack propagation. Three different finite element models can reproduce the collapse behaviours of [±45]3s square tube to some extent, but the stacked shell model can better reproduce the failure mode, and the difference of specific energy absorption (SEA) is minimum, which shows the numerical simulation results are in better agreement with the test results.

scholarly journals Investigation of the Thickness Differential on the Formability of Aluminum Tailor Welded Blanks

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 875
Author(s):  
Jie Wu ◽  
Yuri Hovanski ◽  
Michael Miles
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Numerical Model ◽  
Plastic Strain ◽  
Finite Element Model ◽  
Equivalent Plastic Strain ◽  
Element Model ◽  
Dome Height ◽  
Tailor Welded Blanks ◽  
Simulation Results

A finite element model is proposed to investigate the effect of thickness differential on Limiting Dome Height (LDH) testing of aluminum tailor-welded blanks. The numerical model is validated via comparison of the equivalent plastic strain and displacement distribution between the simulation results and the experimental data. The normalized equivalent plastic strain and normalized LDH values are proposed as a means of quantifying the influence of thickness differential for a variety of different ratios. Increasing thickness differential was found to decrease the normalized equivalent plastic strain and normalized LDH values, this providing an evaluation of blank formability.

scholarly journals 3D Simulation-Based Acoustic Wave Resonator Analysis and Validation Using Novel Finite Element Method Software

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2715
Author(s):  
Ruth Yadira Vidana Morales ◽  
Susana Ortega Cisneros ◽  
Jose Rodrigo Camacho Perez ◽  
Federico Sandoval Ibarra ◽  
Ricardo Casas Carrillo
Keyword(s):  
Finite Element ◽  
High Performance ◽  
Cloud Services ◽  
3D Simulation ◽  
3D Simulations ◽  
Acoustic Resonators ◽  
Analysis And Design ◽  
Wave Resonator ◽  
Film Bulk ◽  
Simulation Results

This work illustrates the analysis of Film Bulk Acoustic Resonators (FBAR) using 3D Finite Element (FEM) simulations with the software OnScale in order to predict and improve resonator performance and quality before manufacturing. This kind of analysis minimizes manufacturing cycles by reducing design time with 3D simulations running on High-Performance Computing (HPC) cloud services. It also enables the identification of manufacturing effects on device performance. The simulation results are compared and validated with a manufactured FBAR device, previously reported, to further highlight the usefulness and advantages of the 3D simulations-based design process. In the 3D simulation results, some analysis challenges, like boundary condition definitions, mesh tuning, loss source tracing, and device quality estimations, were studied. Hence, it is possible to highlight that modern FEM solvers, like OnScale enable unprecedented FBAR analysis and design optimization.

Comprehensive Analysis for Influence of Controllable Damper Time Delay on Semi-Active Suspension Control Strategies

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Yechen Qin ◽  
Feng Zhao ◽  
Zhenfeng Wang ◽  
Liang Gu ◽  
Mingming Dong
Keyword(s):  
Time Delay ◽  
Dynamic Characteristics ◽  
Ride Comfort ◽  
Hybrid Control ◽  
Sliding Mode ◽  
Control Strategies ◽  
Active Suspension ◽  
Test System ◽  
Suspension Control ◽  
Simulation Results

This paper presents a comprehensive comparison and analysis for the effect of time delay on the five most representative semi-active suspension control strategies, and refers to four unsolved problems related to semi-active suspension performance and delay mechanism that existed. Dynamic characteristics of a commercially available continuous damping control (CDC) damper were first studied, and a material test system (MTS) load frame was used to depict the velocity-force map for a CDC damper. Both inverse and boundary models were developed to determine dynamic characteristics of the damper. In addition, in order for an improper damper delay of the form t+τ to be corrected, a delay mechanism of controllable damper was discussed in detail. Numerical simulation for five control strategies, i.e., modified skyhook control SC, hybrid control (HC), COC, model reference sliding mode control (MRSMC), and integrated error neuro control (IENC), with three different time delays: 5 ms, 10 ms, and 15 ms was performed. Simulation results displayed that by changing control weights/variables, performance of all five control strategies varied from being ride comfort oriented to being road handling oriented. Furthermore, increase in delay time resulted in deterioration of both ride comfort and road handling. Specifically, ride comfort was affected more than road handling. The answers to all four questions were finally provided according to simulation results.

Sign in / Sign up

Export Citation Format

Share Document