Hydrothermally Grown Copper-Doped ZnO Nanorods on Flexible Substrate

2019 ◽  
Vol 14 (11) ◽  
pp. 1503-1511 ◽  
Author(s):  
Hafiz Muhammad Salman Ajmal ◽  
Waqar Khan ◽  
Fasihullah Khan ◽  
Noor-ul Huda ◽  
Sam-Dong Kim
Keyword(s):  
Photoelectron Spectroscopy ◽  
Flexible Substrate ◽  
Sol Gel ◽  
Zno Nanorods ◽  
Atomic Ratio ◽  
Crystalline Quality ◽  
Near Band Edge ◽  
Band Edge Emission ◽  
X Ray ◽  
Doped Zno

In this study, we observe the effect of Cu doping on the ZnO nanorod (NR) structure grown on a polyethylene terephthalate flexible substrates by hydrothermal growth of sol–gel method proceeded at 150 °C. Copper (II) nitrate trihydrate (Cu-nitrate) and copper (II) acetate monohydrate (Cu-acetate) are employed as precursors for Cu dopants in aqueous growth solution to examine the evolutionary change of the growth morphology, optical characteristics, and chemical composition of as-grown ZnO NRs. A significant influence of dopant molarity on the morphology of wurtzite ZnO nanocrystals is observed by field-emission scanning electron microscopy. X-ray diffraction analysis also reveals more enhanced crystalline quality from Cu-doped NR crystals prepared by Cu-acetates than that grown with Cu-nitrate precursor. Near band-edge emission of 2 mM Cu-acetate doped NRs is greatly enhanced by 2.5 times compared to those grown with Cu-nitrate precursors. A great reduction in visible emissions is also realized, and this phenomenon is associated with overall improvement in NR crystalline quality by suppressing the oxygenated carbon groups or hydroxyl introduced by the aqueous solution-based growth. X-ray photoelectron spectroscopy also shows that a very high O/Zn atomic ratio of 0.73 can be achieved in the case of NR crystals prepared by 2 mM Cu-acetate. Cu doped ZnO nanostructures of improved optical and structural properties achieved in this study can be utilized in the wide emerging field of flexible device applications such as laser diodes, light-emitting diodes, piezoelectric transducers and generators, gas sensors, and ultraviolet detectors.

Magnetic Properties of Bulk Zn0.95-XMnXFe0.05O2 Prepared by Sol-Gel Method and Subsequent Hot Pressing

2011 ◽  
Vol 268-270 ◽  
pp. 356-359 ◽  
Author(s):  
Wen Song Lin ◽  
C. H. Wen ◽  
Liang He
Keyword(s):  
Magnetic Properties ◽  
Photoelectron Spectroscopy ◽  
Raw Materials ◽  
Sol Gel ◽  
Secondary Phase ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Doped Zno

Mn, Fe doped ZnO powders (Zn0.95-xMnxFe0.05O2, x≤0.05) were synthesized by an ameliorated sol-gel method, using Zn(CH3COO)2, Mn(CH3COO)2and FeCl2as the raw materials, with the addition of vitamin C as a kind of chemical reducer. The resulting powder was subsequently compacted under pressure of 10 MPa at the temperature of 873K in vacuum. The crystal structure and magnetic properties of Zn0.95-xMnxFe0.05O2powder and bulk samples have been investigated by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). X-ray photoelectron spectroscopy (XPS) was used to study chemical valence of manganese, iron and zinc in the samples. The x-ray diffraction (XRD) results showed that Zn0.95-xMnxFe0.05O (x≤0.05) samples were single phase with the ZnO-like wurtzite structure. No secondary phase was found in the XRD spectrum. X-ray photoelectron spectroscopy (XPS) showed that Fe and Mn existed in Zn0.95-xMnxFe0.05O2samples in Fe2+and Mn2+states. The results of VSM experiment proved the room temperature ferromagnetic properties (RTFP) of Mn, Fe co-doped ZnO samples.

scholarly journals Studies of Effects of Calcination Temperature on the Crystallinity and Optical Properties of Ag-Doped ZnO Nanocomposites

2019 ◽  
Vol 3 (1) ◽  
pp. 18 ◽  
Author(s):  
Md. Molla ◽  
Mai Furukawa ◽  
Ikki Tateishi ◽  
Hideyuki Katsumata ◽  
Satoshi Kaneco
Keyword(s):  
Optical Properties ◽  
Calcination Temperature ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Band Edge ◽  
High Yield ◽  
Band Edge Emission ◽  
X Ray ◽  
Calcination Temperatures ◽  
Doped Zno

Ag-doped ZnO nanocomposites are successfully synthesized at different calcination temperatures and times through a simple, effective, high-yield and low-cost mechanochemical combustion technique. Effects of calcination temperature on the crystallinity and optical properties of Ag/ZnO nanocomposites have been studied by X-ray diffraction (XRD), UV−visible diffuse reflectance spectroscopy (UV-DRS), photoluminescence spectroscopy (PL) and X-ray photoelectron spectroscopy (XPS). The XRD patterns of the synthesized Ag/ZnO exhibit a well-crystalline wurtzite ZnO crystal structure. The grain size of Ag/ZnO nanocomposites is found to be 19 and 46 nm at calcination temperatures of 400 °C and 700 °C, respectively. The maximum absorption in the UV region is obtained for Ag/ZnO nanocomposites synthesized at a calcination temperature of 500 °C for 3 h. The peak position of blue emissions is almost the same for the nanocomposites obtained at 300–700 °C calcination temperatures. The usual band edge emission in the UV is not obtained at 330 nm excitation. Band edge and blue band emissions are observed for the use of low excitation energy at 335–345 nm.

scholarly journals Preparation of Ni Doped ZnO-TiO2Composites and Their Enhanced Photocatalytic Activity

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Xiaowen Zou ◽  
Xiaoli Dong ◽  
Limei Wang ◽  
Hongchao Ma ◽  
Xinxin Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Visible Region ◽  
Hydroxyl Groups ◽  
X Ray ◽  
Surface Hydroxyl ◽  
Simulated Solar Light ◽  
Transmission Electron ◽  
Doped Zno

Herein, Ni doped ZnO-TiO2composites were prepared by facile sol-gel approach and were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-visible diffuse reflectance spectroscopy (UV-Vis DRS), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL). The results indicated that the Ni ions can be incorporated into the lattice of TiO2structure and replace Ti. The introduction of Ni expanded light absorption of TiO2to visible region, increased amount of surface hydroxyl groups and physically adsorbed oxygen (as the electronic scavenges), and then enhanced separation rate of photogenerated carriers. The photodegradation test of reactive brilliant blue (KN-R) under simulated solar light indicated that Ni doped ZnO-TiO2composites have better photocatalytic activities, as compared to those of TiO2and ZnO-TiO2.

CHARACTERISTIC ANALYSIS ON GaN NANOCRYSTALLINE POWDER PREPARED BY SOL–GEL METHOD

2007 ◽  
Vol 14 (06) ◽  
pp. 1181-1185 ◽  
Author(s):  
ENLING LI ◽  
XUEWEN WANG ◽  
SHANSHAN WANG ◽  
GUICAN CHEN
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Nanocrystalline Powder ◽  
Band Edge Emission ◽  
Characteristic Analysis ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Luminescence Peak ◽  
Strong Luminescence

Gallium nitride ( GaN ) nanocrystalline powder has been prepared by sol–gel method. The GaN powder has been confirmed as single-crystalline GaN with wurtzite structure by X-ray diffraction (XRD) and selected-area electron diffraction (SAED), and the diameter of the grains of GaN powder changes from 30 to 100 nm under transmission electron microscopy (TEM). Having been excited by 240 nm light at room temperature, GaN powder has a strong luminescence peak located at 395 nm and a weak luminescence peak located at 295 nm, attributed to GaN band-edge emission and blue-shift of the band-gap emission. Moreover, X-ray photoelectron spectroscopy (XPS) confirms the formation of the bond between Ga and N , and Raman scattering spectrum confirms A1 (TO) and E1 (TO) vibrational modes of GaN .

scholarly journals Growth of Zn1−x CdxO nanocrystalline thin films by sol-gel method and their characterization for optoelectronic applications

2014 ◽  
Vol 32 (4) ◽  
pp. 688-695 ◽  
Author(s):  
Munirah Munirah ◽  
Ziaul Khan ◽  
Mohd. Khan ◽  
Anver Aziz
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
Visible Region ◽  
Zno Thin Films ◽  
Band Edge Emission ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cd Doping ◽  
Vis Spectroscopy ◽  
Doped Zno

AbstractThis paper describes the growth of Cd doped ZnO thin films on a glass substrate via sol-gel spin coating technique. The effect of Cd doping on ZnO thin films was investigated using X-ray diffraction (XRD), UV-Vis spectroscopy, photoluminescence spectroscopy, I–V characteristics and field emission scanning electron microscopy (FESEM). X-ray diffraction patterns showed that the films have preferred orientation along (002) plane with hexagonal wurtzite structure. The average crystallite sizes decreased from 24 nm to 9 nm, upon increasing of Cd doping. The films transmittance was found to be very high (92 to 95 %) in the visible region of solar spectrum. The optical band gap of ZnO and Cd doped ZnO thin films was calculated using the transmittance spectra and was found to be in the range of 3.30 to 2.77 eV. On increasing Cd concentration in ZnO binary system, the absorption edge of the films showed the red shifting. Photoluminescence spectra of the films showed the characteristic band edge emission centred over 377 to 448 nm. Electrical characterization revealed that the films had semiconducting and light sensitive behaviour.

scholarly journals Investigation on the Selenization Treatment of Kesterite Cu2Mg0.2Zn0.8Sn(S,Se)4 Films for Solar Cell

Nanomaterials ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 946 ◽  
Author(s):  
Dongyue Jiang ◽  
Yu Zhang ◽  
Yingrui Sui ◽  
Wenjie He ◽  
Zhanwu Wang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Crystal Quality ◽  
Crystalline Quality ◽  
Soda Lime Glass ◽  
Soda Lime Glass Substrate ◽  
X Ray ◽  
Morphological Studies ◽  
Selenization Temperature

High-selenium Cu2Mg0.2Zn0.8Sn(S,Se)4 (CMZTSSe) films were prepared on a soda lime glass substrate using the sol–gel spin coating method, followed by selenization treatment. In this work, we investigated the effects of selenization temperature and selenization time on the crystal quality, and electrical and optical properties of CMZTSSe films. The study on the micro-structure by XRD, Raman, X-ray photoelectron spectroscopy (XPS), and energy-dispersive X-ray spectroscopy (EDS) analysis showed that all CMZTSSe samples had kesterite crystalline structure. In addition, the crystalline quality of CMZTSSe is improved and larger Se takes the site of S in CMZTSSe with the increase of selenization temperature and selenization time. When increasing the selenization temperature from 500 to 530 °C and increasing the annealing time from 10 to 15 min, the morphological studies showed that the microstructures of the films were dense and void-free. When further increasing the temperature and time, the crystalline quality of the films began to deteriorate. In addition, the bandgaps of CMZTSSe are tuned from 1.06 to 0.93 eV through adjusting the selenization conditions. When CMZTSSe samples are annealed at 530 °C for 15 min under Se atmosphere, the crystal quality and optical–electrical characteristics of CMZTSSe will be optimal, and the grain size and carrier concentration reach maximums of 1.5–2.5 μm and 6.47 × 1018 cm−3.

Effect of N and P codoping on ZnO properties

2013 ◽  
Vol 645 ◽  
pp. 64-67 ◽  
Author(s):  
Jin Zhong Wang ◽  
Elangovan Elamurugu ◽  
Hong Tao Li ◽  
Shu Jie Jiao ◽  
Lian Cheng Zhao ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Atomic Ratio ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Nitrogen And Phosphorus ◽  
X Ray ◽  
Co Doping ◽  
Glass Substrates ◽  
Doped Zno ◽  
Co Doped

Nitrogen and Phosphorus co-doped (N+P)- zinc oxide (ZnO) films were RF sputtered on corning glass substrates at 350 °C and comparatively studied with undoped, N-, and P- doped ZnO. X-ray diffraction spectra confirmed that the ZnO structure with a preferred orientation along direction. Scanning electron microscope analysis showed different microstructure for the N+P co-doping, and thus probably confirming the co-existence of both the dopants. X-ray photoelectron spectroscopy spectra revealed that the chemical composition in N+P co-doped ZnO are different from that found in undoped, N-, and P- doped ZnO. The atomic ratio of N and P in N+P co-doped ZnO is higher than that in single N or P doped ZnO. One broad ZnO emission peak around 420 nm is observed in photoluminescence spectra. The relative intensity of the strongest peak obtained from co-doped ZnO films is about twice than the P- doped and thrice than the pure and N- doped films.

Synthesis and Sensing Properties of N-doped ZnO Nanorod Arrays on Quartz

2010 ◽  
Vol 1253 ◽  
Author(s):  
Boqian Yang ◽  
Xiaoyan Peng ◽  
Hongxin Zhang ◽  
Peterxian Feng ◽  
Marc Achermann
Keyword(s):  
Photoelectron Spectroscopy ◽  
Zno Nanorods ◽  
Zno Nanorod ◽  
Nanorod Arrays ◽  
Zno Nanorod Arrays ◽  
X Ray ◽  
Doped Zno ◽  
High Concentrations ◽  
Diffraction Patterns ◽  
Raman Scattering Spectra

AbstractUsing different pressures of nitrogen, N-doped ZnO nanorod arrays of various densities have been synthesized on quartz substrates by pulsed laser deposition techniques. The nanorods grow preferentially perpendicular to the quartz surface. X-ray diffraction patterns revealed some degradation of the crystal structure at elevated nitrogen pressures. High concentrations of nitrogen doping in ZnO nanorods were estimated by X-ray photoelectron spectroscopy. Raman scattering spectra confirmed the wurtzite structure of N-doped ZnO nanorods. A prototype sensor based on the N-doped ZnO nanorod arrays demonstrates a linear dependence of the conductivity with operating temperature and pressure of a test gas pollutant.

scholarly journals Enhanced Ultraviolet Photodetector Based on Mg-Doped ZnO Nanorods Films

2019 ◽  
Vol 29 (3) ◽  
pp. 158 ◽  
Author(s):  
Hussein Abdullah Hameed
Keyword(s):  
Uv Light ◽  
Zno Nanorods ◽  
Optical Absorption Spectroscopy ◽  
Near Band Edge ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Metal Semiconductor Metal ◽  
Doped Zno ◽  
Mg Doped

Magnesium-doped zinc oxide (ZnO: Mg) nanorods and nanotubes films were prepared by hydrothermal method deposited on glass substrates. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), photoluminescence (PL), and optical absorption spectroscopy (UV) were performed to characterize the prepared films. X-ray diffraction analysis showed a decrease in the lattice parameters of Mg doped ZnO NRs. The Photoluminescence of the undoped and Mg-doped ZnO NRs displayed a near band edge. At 10 V bias, the metal-semiconductor-metal (MSM) ultraviolet (UV) photodetector performance of the Mg-doped ZnO prepared for various Mg concentrations of 0.0, 0.02, and 0.06 was investigated under radiation of 40μW/cm2 at the wavelengths of 365 and 385 nm UV light. The responsivity, detectivity and quantum efficiency of Mg-doped based on MSM detector were 0.118A/W, 1.0579*1012 and 40.05157 under UV of wavelength 365nm respectively.

scholarly journals Synthesis of Fe-Doped ZnO Nanorods by Rapid Mixing Hydrothermal Method and Its Application for High Performance UV Photodetector

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Chan Oeurn Chey ◽  
Ansar Masood ◽  
A. Riazanova ◽  
Xianjie Liu ◽  
K. V. Rao ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Zno Nanorods ◽  
Hexagonal Wurtzite Structure ◽  
Secondary Phases ◽  
Simple Method ◽  
Uv Photodetector ◽  
X Ray ◽  
Doped Zno ◽  
Schottky Devices

We have successfully synthesized Fe-doped ZnO nanorods by a new and simple method in which the adopted approach is by using ammonia as a continuous source ofOH-for hydrolysis instead of hexamethylenetetramine (HMT). The energy dispersive X-ray (EDX) spectra revealed that the Fe peaks were presented in the grown Fe-doped ZnO nanorods samples and the X-ray photoelectron spectroscopy (XPS) results suggested that Fe3+is incorporated into the ZnO lattice. Structural characterization indicated that the Fe-doped ZnO nanorods grow along thec-axis with a hexagonal wurtzite structure and have single crystalline nature without any secondary phases or clusters of FeO or Fe3O4observed in the samples. The Fe-doped ZnO nanorods showed room temperature (300 K) ferromagnetic magnetization versus field (M-H) hysteresis and the magnetization increases from 2.5 μemu to 9.1 μemu for Zn0.99Fe0.01O and Zn0.95Fe0.05O, respectively. Moreover, the fabricated Au/Fe-doped ZnO Schottky diode based UV photodetector achieved 2.33 A/W of responsivity and 5 s of time response. Compared to other Au/ZnO nanorods Schottky devices, the presented responsivity is an improvement by a factor of 3.9.

Sign in / Sign up

Export Citation Format

Share Document