Experimental evaluation and modified Weibull characterization of the tensile behavior of tri-component elastic-conductive composite yarn

2017 ◽  
Vol 88 (10) ◽  
pp. 1138-1149 ◽  
Author(s):  
Yong Wang ◽  
Weidong Yu ◽  
Fumei Wang
Keyword(s):  
Tensile Strength ◽  
Strength Distribution ◽  
Gauge Length ◽  
Distribution Model ◽  
Fracture Mechanisms ◽  
Extension Rate ◽  
Strengthening Effect ◽  
Conductive Composite ◽  
Practical Applications ◽  
Composite Yarn

In order to clarify the effects of the extension rate and gauge length upon the distribution of tensile strength of tri-component elastic-conductive composite yarn (t-ECCY), experimental as well as theoretical studies have been performed in this paper. Influences of the extension rate and gauge length are highlighted. The yarn exhibits an extension-rate strengthening effect, and the higher extension rate results in a higher strength and fracture strain, irrespective of the gauge length considered, and vice versa. Expressed in terms of gauge length, yarn tenacity shows a drop for a longer testing length at all extension rates, based on the weakest-link theory. A modified two-parameter Weibull strength distribution model, taking into account the effects of extension rate and gauge length, can be reasonably used to quantify the degree of variability in tensile strength and to obtain the individual Weibull parameters for practical applications. Different fracture mechanisms of the t-ECCY are demonstrated at lower and higher extension rates. A “cascade-like” break happens at lower extension rates due to inner sliding, weaker interactive transverse force of individual fibers, and sufficient time available for the fiber realignment. Nevertheless, a “chimney-like” break dominates at higher extension rates by virtue of the reduced reorientation of some disordered fibers and intensive instant impact force of the stainless steel filament component along the load direction.

Characterization and comparison of properties of cryogenic conditioned CNT reinforced thermoset (epoxy) and thermoplastic (poly vinyl alcohol) composite yarns

2021 ◽  
pp. 002199832110417
Author(s):  
Wei Chen ◽  
Yifan Wang ◽  
Kun Zhang ◽  
Fujun Xu
Keyword(s):  
Tensile Strength ◽  
Vinyl Alcohol ◽  
Thermoplastic Composite ◽  
Advanced Materials ◽  
Poly Vinyl Alcohol ◽  
Practical Applications ◽  
Mechanical And Electrical Properties ◽  
Composite Yarn ◽  
Thermoset Epoxy ◽  
New Generation

Carbon nanotube (CNT) fiber/yarn reinforced composites are considered as a new generation of advanced materials for applications in aerospace and space industry. In this study, two types of CNT composite yarns were produced by twisting CNT films and infiltrating with thermoset epoxy (EP) and thermoplastic poly vinyl alcohol (PVA) resins. The tensile strength of CNT/PVA and CNT/EP composite yarn was 409.91 MPa and 206.87 MPa, much higher than that of pure CNT yarn (129.94 MPa). After mono-cryogenic condition, the mechanical and electrical properties of CNT/EP and CNT/PVA composite yarns were both enhanced due to the structure reorder of the CNT bundles and improvement of interfacial bonding. However, after 60 times cyclic-cryogenic conditions, CNT/EP composite yarn showed a ∼10% degradation of tensile strength; while CNT/PVA composite yarn exhibited 6% increment. This study provides fundamental data of the CNT reinforced thermoset and thermoplastic composite yarns for their practical applications in cryogenic environment.

Microstructure and mechanical properties of reinforced polyamide 12 composites prepared by laser additive manufacturing

2019 ◽  
Vol 25 (6) ◽  
pp. 1127-1134 ◽  
Author(s):  
Yanhui Liu ◽  
Lingjie Zhu ◽  
Lei Zhou ◽  
Yongjiu Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Selective Laser Sintering ◽  
Tensile Fracture ◽  
Fracture Mechanisms ◽  
Strengthening Effect ◽  
Content Type ◽  
Tensile Fracture Surface ◽  
Polyamide 12 ◽  
Microstructure And Mechanical Properties

Purpose This paper aims to explore the influence of the reinforcement included either glass beads (GBs) or carbon fiber (CF) on the reinforced polyamide 12 (PA12) composite samples prepared by selective laser sintering (SLS). Design/methodology/approach In this paper, the microstructure and mechanical properties are investigated, and the results are compared with those obtained for non-reinforced pure PA12 samples prepared by SLS. Findings The tensile fracture surface of the non-reinforced pure PA12 sample presents strong micro-deformation within the crack origination zone between the melted PA12 matrix and the un-melted PA12 particle cores. As a result, the pure PA12 sample exhibits the greatest maximum elongation. The maximum tensile strength is obtained for the CF reinforced sample because of the strengthening effect of CF and the relatively good bonding between CFs and the PA12 matrix. The minimum tensile strength is obtained for the GB reinforced PA12 sample because of the relatively weak bonding between GBs and the PA12 matrix. Originality/value These results demonstrate that the characteristics of the interfaces between the reinforcement and the PA12 matrix have an important influence on the fracture mechanisms and mechanical properties of PA12 composites fabricated by SLS.

Mechanical properties of low-density paper

2020 ◽  
Vol 35 (1) ◽  
pp. 61-70
Author(s):  
Na Young Park ◽  
Young Chan Ko ◽  
Lili Melani ◽  
Hyoung Jin Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Structural Change ◽  
Tensile Testing ◽  
Tensile Modulus ◽  
Gauge Length ◽  
Efficiency Factor ◽  
Low Density ◽  
Tensile Stiffness ◽  
Lower Tensile Strength

AbstractFor the mechanical properties of paper, tensile testing has been widely used. Among the tensile properties, the tensile stiffness has been used to determine the softness of low-density paper. The lower tensile stiffness, the greater softness of paper. Because the elastic region may not be clearly defined in a load-elongation curve, it is suggested to use the tensile modulus which is defined as the slope between the two points in the curve. The two points which provide the best correlation with subjective softness evaluation should be selected. Low-density paper has a much lower tensile strength, but much larger elongation at the break. It undergoes a continuous structural change during mechanical testing. The degree of the structural change should depend on tensile conditions such as the sample size, the gauge length, and the rate of elongation. For low-density paper, the tensile modulus and the tensile strength should be independent of each other. The structure efficiency factor (SEF) is defined as a ratio of the tensile strength to the tensile modulus and it may be used a guideline in developing superior low-density paper products.

Characterization and Utilization of Coconut Fibers of the Caribbean

2014 ◽  
Vol 1611 ◽  
pp. 95-104 ◽  
Author(s):  
Nadira Mathura ◽  
Duncan Cree ◽  
Ryan P. Mulligan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Micrographs ◽  
Saline Water ◽  
Gauge Length ◽  
Scanning Electron Micrographs ◽  
Coir Fiber ◽  
Coir Fibers ◽  
The Caribbean ◽  
Scanning Electron

ABSTRACTIn many tropical countries coconut (coir) fiber production is a major source of income for rural communities. The Caribbean has an abundance of coconuts but research into utilizing its by-products is limited. Environmentally friendly coir fibers are natural polymers generally discarded as waste material in this region. Research has shown that coir fiber from other parts of the world has successfully been recycled. This paper therefore investigates the mechanical properties of Caribbean coir fiber for potential applications in civil engineering.Approximately four hundred fibers were randomly taken from a coir fiber stack and subjected to retting in both distilled and saline water media. The mechanical properties of both the retted and unretted coir fibers were evaluated at weekly increments for a period of 3 months. Tensile strength test, x-ray diffraction analysis and scanning electron micrographs were used to assess trends and relationships between fiber gauge lengths, diameter, tensile strength and Young’s modulus. Diameters ranged between 0.11 mm-0.46 mm, while fiber samples were no longer than 250 mm in length. The tensile strength and strain at break decreased as the gauge length increased for both unretted and retted fibers. The opposite occurred for the relationship between the gauge length and Young’s modulus. Additionally, the tensile strength and modulus decreased as the fiber diameter increased. Neither distilled nor saline water improved the coir fiber’s crystalline index. Scanning electron micrographs qualitatively assessed fiber surfaces and captured necking and microfibril degradation at the fractured ends.The analysis revealed that the tensile strength, modulus, strain at break and crystallinity properties of the Caribbean coir fibers were comparable to commercially available coir fiber which are currently being used in many building applications.

The Effect of Yarn Linear Density on Mechanical Properties of Plain Woven Kenaf Reinforced Unsaturated Polyester Composite

2013 ◽  
Vol 465-466 ◽  
pp. 962-966 ◽  
Author(s):  
Mohd Pahmi bin Saiman ◽  
Mohd Saidin Bin Wahab ◽  
Mat Uzir Wahit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Linear Density ◽  
Unsaturated Polyester ◽  
Composite Panel ◽  
Composite Yarn ◽  
Polyester Composite ◽  
The Impact ◽  
Woven Kenaf

To produce a good quality of dry fabric for reinforced material in a natural-based polymer composite, yarn linear density should be in consideration. A woven kenaf dry fabric with three different linear densities of 276tex, 413.4tex and 759tex were produced. The fabrics with different linear densities were been optimize with the assistance of WiseTex software. The optimized dry fabrics were infused with unsaturated polyester to produce composite panel using vacuum infusion process. The composites properties were tested on the tensile strength, flexural strength and the impact strength. The result shows that the mechanical properties of the composite increased when the yarn linear densities increased.

Electromagnetic Shielding Effectiveness and Manufacturing Technique of Metal Complex Fabrics

2014 ◽  
Vol 496-500 ◽  
pp. 472-475
Author(s):  
Ching Wen Lou ◽  
An Pang Chen ◽  
Ting An Lin ◽  
Ya Yuan Chuang ◽  
Jia Horng Lin
Keyword(s):  
Metal Complex ◽  
Life Time ◽  
Woven Fabrics ◽  
Electromagnetic Shielding ◽  
Test Results ◽  
Test Frequency ◽  
Shielding Effectiveness ◽  
Conductive Composite ◽  
Composite Yarn ◽  
Electromagnetic Shielding Effectiveness

In the research, The electromagnetic interferences (EMI) have drastically increased and can disrupt and reduce the life time and the efficiency of devices. Therefore, the electromagnetic shielding problem is become the important issue. In the research, Ni wire and Cu wire (Floodlit Enterprise Co., Ltd.) were used to make the Ni conductive composite yarn and Cu conductive composite yarn via an electrical covering machine. And the Cu conductive composite yarn was fabricated to the woven fabrics with the plain weaving. The test results revealed that the EMSE of the W/K/W complex fabrics have stable EMSE than the W/W/W complex fabrics when the laminated at the same direction. The W/90W/W complex woven fabrics were shown the best EMSE of 46.25 dB, which the test frequency is 1800 MHz.

scholarly journals Cracking and Toughening Mechanisms in Nanoscale Metallic Multilayer Films: A Brief Review

2018 ◽  
Vol 8 (10) ◽  
pp. 1821 ◽  
Author(s):  
Qing Zhou ◽  
Yue Ren ◽  
Yin Du ◽  
Dongpeng Hua ◽  
Weichao Han
Keyword(s):  
Fracture Toughness ◽  
High Strength ◽  
Plastic Instability ◽  
Multilayer Films ◽  
Fracture Mechanisms ◽  
Toughening Mechanisms ◽  
Individual Layer ◽  
Practical Applications ◽  
Mechanical Responses ◽  
The Individual

Nanoscale metallic multilayer films (NMMFs) have captured scientific interests on their mechanical responses. Compared with the properties of monolithic films, multilayers possess unique high strength as the individual layer thickness reduces to the nanoscale, which is benefited from the plentiful hetero-interfaces. However, NMMFs always exhibit a low fracture toughness and ductility, which seriously hinders their practical applications. While there have been reviews on the strengthening and deformation mechanisms of microlaminate, rapid developments in nanotechnology have brought an urgent requirement for an overview focused on the cracking and toughening mechanisms in nanoscale metallic multilayers. This article provides an extensive review on the structure, standard methodology and fracture mechanisms of NMMFs. A number of issues about the crack-related properties of NMMFs have been displayed, such as fracture toughness, wear resistance, adhesion energy, and plastic instability. Taken together, it is hoped that this review will achieve the following two purposes: (1) introducing the size-dependent cracking and toughness performance in NMMFs; and (2) offer a better understanding of the role interfaces displayed in toughening mechanisms. Finally, we list a few questions we concerned, which may shed light on further development.

scholarly journals Characterizing Distributions of Tensile Strength and Crack Precursor Size to Evaluate Filler Dispersion Effects and Reliability of Rubber

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 203 ◽  
Author(s):  
Christopher G. Robertson ◽  
Lewis B. Tunnicliffe ◽  
Lawrence Maciag ◽  
Mark A. Bauman ◽  
Kurt Miller ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Average Diameter ◽  
Strength Distribution ◽  
Glass Beads ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Failure Distribution ◽  
Filler Dispersion ◽  
Control Compound ◽  
Styrene Butadiene

Undispersed filler agglomerates or other substantial inclusions/contaminants in rubber can act as large crack precursors that reduce the strength and fatigue lifetime of the material. To demonstrate this, we use tensile strength (stress at break, σb) data from 50 specimens to characterize the failure distribution behavior of carbon black (CB) reinforced styrene-butadiene rubber (SBR) compounds. Poor mixing was simulated by adding a portion of the CB late in the mixing process, and glass beads (microspheres) with 517 μm average diameter were introduced during milling to reproduce the effects of large inclusions. The σb distribution was well described with a simple unimodal Weibull distribution for the control compound, but the tensile strengths of the poor CB dispersion material and the compounds with the glass beads required bimodal Weibull distributions. For the material with the lowest level of glass beads—corresponding to less than one microsphere per test specimen—the bimodal failure distribution spanned a very large range of σb from 13.7 to 22.7 MPa in contrast to the relatively narrow σb distribution for the control from 18.4 to 23.8 MPa. Crack precursor size (c0) distributions were also inferred from the data, and the glass beads introduced c0 values in the 400 μm range compared to about 180 μm for the control. In contrast to σb, critical tearing energy (tear strength) was unaffected by the presence of the CB agglomerates and glass beads, because the strain energy focuses on the pre-cut macroscopic crack in the sample during tear testing rather than on the microscopic crack precursors within the rubber. The glass beads were not detected by conventional filler dispersion measurements using interferometric microscopy, indicating that tensile strength distribution characterization is an important complementary approach for identifying the presence of minor amounts of large inclusions in rubber.

Sign in / Sign up

Export Citation Format

Share Document