scholarly journals The Effect of Sulphur Dioxide on the Adsorption Properties of Activated Carbon towards Chloropicrin

1997 ◽  
Vol 15 (7) ◽  
pp. 541-550 ◽  
Author(s):  
P.J.C. Anstice ◽  
J.F. Alder
Keyword(s):  
Activated Carbon ◽  
Sulphur Dioxide ◽  
Bound States ◽  
Activated Carbons ◽  
Mass Gain ◽  
Adsorption Properties ◽  
Gradual Reduction ◽  
Sulphur Oxide ◽  
Adsorbed Mass ◽  
Carbon Mass

Sulphur dioxide is believed to be adsorbed on activated carbons in both physically and chemically bound states. Sulphuric acid and a variety of oxygenated and hydrated sulphur oxide species are believed to be present on humidified carbons exposed to sulphur dioxide. Samples of ASC/T impregnated carbons were exposed to sulphur dioxide mixtures in humid air at 80% RG and 22°C. The sulphur dioxide-loaded carbons were then exposed to chloropicrin challenge at 5 mg/dm3 in air at 80% RH and 22°C and the chloropicrin breakthrough times measured. A relationship was found between the extra mass gain of the carbons (due to oxygen and water) with increasing sulphur dioxide loading, as predicted by other workers. The effect of sulphur dioxide loading on the chloropicrin breakthrough times was a gradual reduction to about one-third the time for unexposed carbon, with an adsorbed mass of sulphur dioxide equal to ca. 10% of the carbon mass in a 20 mm bed-depth filter.

scholarly journals Coal-Based Activated Carbons for the Removal of Sulphur Dioxide via Adsorption

1997 ◽  
Vol 15 (10) ◽  
pp. 803-814 ◽  
Author(s):  
A.M. Youssef ◽  
M.R. Mostafa ◽  
E.M. Dorgham
Keyword(s):  
Activated Carbon ◽  
Low Temperature ◽  
Zinc Chloride ◽  
Sulphur Dioxide ◽  
Activated Carbons ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Carbon Surface ◽  
Steam Activation ◽  
Pore Widening

Zinc chloride-activated carbons and steam-activated carbons were prepared from Maghara coal. The textural properties were determined from low-temperature nitrogen adsorption. Zinc chloride activation is usually associated with the creation of new micropores while steam activation involves pore widening particularly when the percentage burn-off is high. The adsorption of SO2 on steam-activated carbon is high compared with ZnCl2-activated carbons. Steam activation develops surface basic groups which provide chemisorption sites for SO2. The adsorption of SO2 is enhanced in the presence of O2 and water vapour and involves the formation of sulphuric acid in this case. Sulphur dioxide adsorption is related to the chemistry of the carbon surface rather than to the extent of the surface area of the activated carbon.

scholarly journals Purification of spent methyldiethanolamine solutions with activated carbon au-ko

2020 ◽  
Vol 5 ◽  
pp. 83-88
Author(s):  
Isokov Yusuf Khoriddinovich ◽  
Kurbonov Azizjon Rustamovich ◽  
Pulatova Zulkhumor Jaloliddin kizi ◽  
Yusupov Farkhod Makhkamovich ◽  
Sultonov Sadulla Bahriddinovich ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Import Substitution ◽  
Adsorption Properties ◽  
Technological Parameters ◽  
Adsorption Characteristics

The article presents the results of a study to determine the physicochemical adsorption properties and some technological parameters for the production of activated carbons based on bones.  In the course of the study, the physicochemical and adsorption characteristics of the new activated carbon obtained by us from walnut seeds were determined.  For the purpose of import substitution, its characteristics were compared with the well-known industrial activated carbon of the AG-3 brand.

scholarly journals Research on the Development of Technologies for the Production of Granulated Activated Carbons Using Various Binders

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5180
Author(s):  
Iwona Skoczko ◽  
Remigiusz Guminski
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Raw Materials ◽  
Sodium Carboxymethylcellulose ◽  
Industrial Plants ◽  
Carbon Production ◽  
Carbon Mass ◽  
Available Technology ◽  
Very High ◽  
Granulated Activated Carbon

Activated carbons (ACs) are processed carbon-rich materials with a highly developed inner surface and significant porosity used for different media treatment in municipal and industrial plants. Activated carbon may be manufactured as powdered activated carbon (PAC), gritty activated carbon (in a form of raw angels grains) or granulated activated carbon (GAC). The production of the GAC is based on carbonaceous raw materials and various types of binders. The carbon mass is mixed with the binder and formed in cylindrical granules. The binder’s recognition is in a scientific literature side-topic and still needs wider examination. For many years GAC production have been concentrated on the possibility of using sodium carboxymethylcellulose (SCMC). Therefore, the aim of the research was to develop a new binder, in the available technology of granulated activated carbon production. Such binders were tested such as: tall oil (TO), sugar beet molasses (SBM), sodium carboxymethylcellulose (SCMC), SCMC using a verified technological process and SCMC with the addition of gas tar (GT). The conducted research shows that all the quality requirements were met by activated carbons with SBM as a binder. Additionally they showed very high adsorption properties. The manufacturing process was shorter in comparison to other tested binders and more efficient.

Research of Citric Acid Modified Adsorption of Cr (VI) Properties of Activated Carbons

2014 ◽  
Vol 809-810 ◽  
pp. 901-906
Author(s):  
Chen Li Wang ◽  
Jin Chuan Gu ◽  
Chun Mei Wei ◽  
Li Fang Bao ◽  
Rui Wang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Citric Acid ◽  
Acid Concentration ◽  
Rate Equation ◽  
Treatment Time ◽  
Activated Carbons ◽  
Adsorption Properties ◽  
Adsorption Rate ◽  
Citric Acid Concentration ◽  
Modified Activated Carbon

Citric acid modification of activated carbon to examine citric acid concentration, temperature and time modified adsorption properties of activated carbon. The results demonstrate that with the extension of temperature and treatment time, the adsorption properties of modified activated carbon were then decreased overall trend. Better process for citric acid modified activated carbon: citric acid concentration of 50%, modified temperature is 30°C, modified time is 5h. Lagergren adsorption rate equation with primary and secondary adsorption rate equation and the average absolute deviation from the rate on the adsorption properties of these factors affects the processing; secondary adsorption kinetics model was found to better describe the various factors affecting the adsorption process under conditions.

Use of activated carbon to remove undesirable residual amylase from refinery streams

2017 ◽  
pp. 96-103 ◽  
Author(s):  
Gillian Eggleston ◽  
Isabel Lima ◽  
Emmanuel Sarir ◽  
Jack Thompson ◽  
John Zatlokovicz ◽  
...  
Keyword(s):  
Activated Carbon ◽  
High Temperature ◽  
High Performance ◽  
Activated Carbons ◽  
Amylase Activity ◽  
Sugar Industry ◽  
End User ◽  
Customer Complaints ◽  
Carry Over ◽  
Very High

In recent years, there has been increased world-wide concern over residual (carry-over) activity of mostly high temperature (HT) and very high temperature (VHT) stable amylases in white, refined sugars from refineries to various food and end-user industries. HT and VHT stable amylases were developed for much larger markets than the sugar industry with harsher processing conditions. There is an urgent need in the sugar industry to be able to remove or inactivate residual, active amylases either in factory or refinery streams or both. A survey of refineries that used amylase and had activated carbon systems for decolorizing, revealed they did not have any customer complaints for residual amylase. The use of high performance activated carbons to remove residual amylase activity was investigated using a Phadebas® method created for the sugar industry to measure residual amylase in syrups. Ability to remove residual amylase protein was dependent on the surface area of the powdered activated carbons as well as mixing (retention) time. The activated carbon also had the additional benefit of removing color and insoluble starch.

Effect of Polyphosphate on Removal of Endocrine-Disrupting Chemicals of Nonylphenol and Bisphenol-A by Activated Carbons

2005 ◽  
Vol 40 (4) ◽  
pp. 484-490 ◽  
Author(s):  
Keun J. Choi ◽  
Sang G. Kim ◽  
Chang W. Kim ◽  
Seung H. Kim
Keyword(s):  
Activated Carbon ◽  
Bisphenol A ◽  
Surface Charge ◽  
Activated Carbons ◽  
Endocrine Disrupting Chemicals ◽  
Dipole Interaction ◽  
High Affinity ◽  
Calcium Polyphosphate ◽  
Endocrine Disrupting ◽  
Positively Charged

Abstract This study examined the effect of polyphosphate on removal of endocrine-disrupting chemicals (EDCs) such as nonylphenol and bisphenol-A by activated carbons. It was found that polyphosphate aided in the removal of nonylphenol and bisphenol- A. Polyphosphate reacted with nonylphenol, likely through dipole-dipole interaction, which then improved the nonylphenol removal. Calcium interfered with this reaction by causing competition. It was found that polyphosphate could accumulate on carbon while treating a river. The accumulated polyphosphate then aided nonylphenol removal. The extent of accumulation was dependent on the type of carbon. The accumulation occurred more extensively with the wood-based used carbon than with the coal-based used carbon due to the surface charge of the carbon. The negatively charged wood-based carbon attracted the positively charged calcium-polyphosphate complex more strongly than the uncharged coal-based carbon. The polyphosphate-coated activated carbon was also effective in nonylphenol removal. The effect was different depending on the type of carbon. Polyphosphate readily attached onto the wood-based carbon due to its high affinity for polyphosphate. The attached polyphosphate then improved the nonylphenol removal. However, the coating failed to attach polyphosphate onto the coal-based carbon. The nonylphenol removal performance of the coal-based carbon remained unchanged after the polyphosphate coating.

scholarly journals 1.8 V Aqueous Symmetric Carbon-Based Supercapacitors with Agarose-Bound Activated Carbons in an Acidic Electrolyte

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1731
Author(s):  
Chih-Chung Lai ◽  
Feng-Hao Hsu ◽  
Su-Yang Hsu ◽  
Ming-Jay Deng ◽  
Kueih-Tzu Lu ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Sulfuric Acid ◽  
Energy Density ◽  
Activated Carbons ◽  
High Energy ◽  
Aqueous Electrolytes ◽  
Alternative Material ◽  
Aqueous Cells ◽  
Acidic Electrolyte ◽  
Cycling Behavior

The specific energy of an aqueous carbon supercapacitor is generally small, resulting mainly from a narrow potential window of aqueous electrolytes. Here, we introduced agarose, an ecologically compatible polymer, as a novel binder to fabricate an activated carbon supercapacitor, enabling a wider potential window attributed to a high overpotential of the hydrogen-evolution reaction (HER) of agarose-bound activated carbons in sulfuric acid. Assembled symmetric aqueous cells can be galvanostatically cycled up to 1.8 V, attaining an enhanced energy density of 13.5 W h/kg (9.5 µW h/cm2) at 450 W/kg (315 µW/cm2). Furthermore, a great cycling behavior was obtained, with a 94.2% retention of capacitance after 10,000 cycles at 2 A/g. This work might guide the design of an alternative material for high-energy aqueous supercapacitors.

scholarly journals The influence of active carbon contaminants on the ozonation mechanism interpretation

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Lilla Fijołek ◽  
Joanna Świetlik ◽  
Marcin Frankowski
Keyword(s):  
Activated Carbon ◽  
Active Carbon ◽  
Alkali Metals ◽  
Activated Carbons ◽  
Carbon Surface ◽  
Bulk Solution ◽  
Ozone Decomposition ◽  
Reaction Products ◽  
Treatment Technology ◽  
Carbon Impurities

AbstractIn water treatment technology, activated carbons are used primarily as sorbents to remove organic impurities, mainly natural organic matter, but also as catalysts in the ozonation process. Commercially available activated carbons are usually contaminated with mineral substances, classified into two main groups: alkali metals (Ca, Na, K, Li, Mg) and multivalent metals (Al, Fe, Ti, Si). The presence of impurities on the carbon surface significantly affects the pHpzc values determined for raw and ozonated carbon as well as their acidity and alkalinity. The scale of the observed changes strongly depends on the pH of the ozonated system, which is related to the diffusion of impurities from the carbon to the solution. In an acidic environment (pH 2.5 in this work), the ozone molecule is relatively stable, yet active carbon causes its decomposition. This is the first report that indirectly indicates that contaminants on the surface of activated carbon (multivalent elements) contribute to the breakdown of ozone towards radicals, while the process of ozone decomposition by purified carbons does not follow the radical path in bulk solution. Carbon impurities also change the distribution of the reaction products formed by organic pollutants ozonation, which additionally confirms the radical process. The study showed that the use of unpurified activated carbon in the ozonation of succinic acid (SA) leads to the formation of a relatively large amount of oxalic acid (OA), which is a product of radical SA degradation. On the other hand, in solutions with purified carbon, the amount of OA generated is negligible.

scholarly journals Computer Analysis of the Effect of Activation Temperature on the Microporous Structure Development of Activated Carbon Derived from Common Polypody

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2951
Author(s):  
Mirosław Kwiatkowski ◽  
Jarosław Serafin ◽  
Andy M. Booth ◽  
Beata Michalkiewicz
Keyword(s):  
Activated Carbon ◽  
Porous Structure ◽  
Computer Analysis ◽  
Density Functional ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Geometrical Parameters ◽  
Activation Process ◽  
Microporous Structure ◽  
Activation Temperature

This paper presents the results of a computer analysis of the effect of activation process temperature on the development of the microporous structure of activated carbon derived from the leaves of common polypody (Polypodium vulgare) via chemical activation with phosphoric acid (H3PO4) at activation temperatures of 700, 800, and 900 °C. An unconventional approach to porous structure analysis, using the new numerical clustering-based adsorption analysis (LBET) method together with the implemented unique gas state equation, was used in this study. The LBET method is based on unique mathematical models that take into account, in addition to surface heterogeneity, the possibility of molecule clusters branching and the geometric and energy limitations of adsorbate cluster formation. It enabled us to determine a set of parameters comprehensively and reliably describing the porous structure of carbon material on the basis of the determined adsorption isotherm. Porous structure analyses using the LBET method were based on nitrogen (N2), carbon dioxide (CO2), and methane (CH4) adsorption isotherms determined for individual activated carbon. The analyses carried out showed the highest CO2 adsorption capacity for activated carbon obtained was at an activation temperature of 900 °C, a value only slightly higher than that obtained for activated carbon prepared at 700 °C, but the values of geometrical parameters determined for these activated carbons showed significant differences. The results of the analyses obtained with the LBET method were also compared with the results of iodine number analysis and the results obtained with the Brunauer–Emmett–Teller (BET), Dubinin–Radushkevich (DR), and quenched solid density functional theory (QSDFT) methods, demonstrating their complementarity.

Sign in / Sign up

Export Citation Format

Share Document