Synthesis of high Tg and organosoluble poly(N-arylene benzimidazole ether imide) copolymers by C–N/C–O coupling reaction

2017 ◽  
Vol 30 (4) ◽  
pp. 465-474 ◽  
Author(s):  
Lala Rukh Sidra ◽  
Nafeesa Mushtaq ◽  
Guofei Chen ◽  
Xingzhong Fang
Keyword(s):  
Mechanical Properties ◽  
Diphenyl Ether ◽  
Coupling Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Good Thermal Stability ◽  
Copolymer Films ◽  
Good Solubility ◽  
Nucleophilic Displacement ◽  
Amorphous Nature

A series of poly( N-arylene benzimidazole ether imide) copolymers PEIBIs were prepared from 1H,3′H-5,5′-bis-benzimidazole, bisphenol-A and 4,4′-bis(4-fluorophthalimido)diphenyl ether by nucleophilic displacement polymerization. The resulting copolymers PEIBI(10–90) demonstrated moderate to good solubility in polar aprotic solvents and high glass transition temperatures ( Tgs) of 228–336°C, good thermal stability with 10% weight loss temperatures in the range of 503–548°C. All copolymer films showed good mechanical properties with tensile strengths of 101–130 MPa, tensile moduli of 3.3–4.0 GPa, elongations at break of 5–7%, and also presented low water uptake (0.15–0.34%). The wide-angle X-ray diffraction results revealed the amorphous nature of copolymers. The copolymer PEIBI-80 showed good balance in solubility, thermal and mechanical properties.

Phenylethynyl-terminated oligoimides with ultra-low melt viscosity derived from 1,4-bis(3,4-dicarboxy phenoxy)benzene dianhydride

2019 ◽  
Vol 31 (5) ◽  
pp. 580-589 ◽  
Author(s):  
Wei Wang ◽  
Guofei Chen ◽  
Xingzhong Fang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Aromatic Diamines ◽  
Melt Viscosity ◽  
X Ray ◽  
Good Thermal Stability ◽  
Molecular Weights ◽  
Chemical Structures ◽  
Very High

Most of the existing polyimide oligomers for resin transfer molding (RTM) processing exhibited high melt viscosity, which can only maintain below 1 Pa·s at 280°C for 2 h, leading to very high process temperatures. So novel RTM-type oligomers with lower and stable melt viscosities are more desirable. Three series of thermoset oligoimides derived from 1,4-bis(3,4-dicarboxy phenoxy)benzene dianhydride and three different aromatic diamines were prepared herein. The diamines included 4,4′-oxydianiline, 2,2′-bis(trifluoromethyl)benzidine (TFDB), and 2-phenyl-4,4′-diaminodiphenyl ether ( p-ODA). 4-Phenylethynylphthalic anhydride was used as an endcapping reagent. Effects of the chemical structures and molecular weights of the oligoimides on their aggregated structures, melt processability, and the thermal and mechanical properties of the cured films were then systematically investigated. X-Ray diffraction results indicated that ODA series oligoimides and TFDB series oligoimides showed crystallinity in various degrees. However, the asymmetric p-ODA enables the p-ODA series oligoimides to exhibit amorphous forms. It was found that the p-ODA-based oligoimide with a molecular weight of 750 g mol−1 showed very low melt viscosity of 1 Pa·s even at 210°C, and the melt viscosity could maintain below 1 Pa·s after isothermal aging for 2 h at any temperature in the range of 200–280°C by rheological measurements. The cured film also showed a high glass transition temperature of 355°C by dynamic mechanical analysis, very good thermal stability by thermogravimetric analysis, and good mechanical properties. It might be more suitable for RTM processes in the future.

Synthesis and application of functionalized ionic liquids as solvent to corn stalk for phenolic resin modification

e-Polymers ◽  
2015 ◽  
Vol 15 (3) ◽  
pp. 195-201 ◽  
Author(s):  
Liying Guo ◽  
Bin Zhang ◽  
Shiyang Bai ◽  
Xiuyun Ma ◽  
Zhiming Wang
Keyword(s):  
Mechanical Properties ◽  
Ionic Liquids ◽  
Phenolic Resin ◽  
Corn Stalk ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
H Nmr ◽  
Good Solubility

AbstractThree functionalized ionic liquids (ILs) of [HeMIM]Cl, [CeMIM]Cl, and [AeMIM]Br that can dissolve corn stalk were synthesized and characterized via Fourier transform infrared spectroscopy (FTIR) and 1H NMR. The dissolved corn stalk was in situ blended with phenol and formaldehyde to produce modified phenolic resin composites. The resulting composites were characterized via FTIR, differential scanning calorimetry, and X-ray diffraction analysis, and tested for their mechanical properties. In addition, the effects of ILs on the dissolution rate of corn stalks and on the mechanical properties of the modified phenolic resin were investigated as well. The results showed that the synthesized ILs presented good solubility toward corn stalk at the optimum temperature of 90°C. After modification with corn stalk dissolved in ILs, the mechanical properties of phenolic resin were significantly improved. At the same conditions, the phenolic resin modified with [AeMIM]Br presented the lowest concentration of free formaldehyde and the best mechanical properties, in which the tensile strength and impact strength were improved from 3.28 MPa and 0.93 kJ/m2 to 9.36 MPa and 5.74 kJ/m2, respectively, but the hardness only changed slightly.

Synthesis and characterization of polyhydrazides and poly(1,3,4-oxadiazole)s containing multiple arylene ether linkages and pendent pentadecyl chains

2016 ◽  
Vol 29 (7) ◽  
pp. 836-848 ◽  
Author(s):  
Bhausaheb V Tawade ◽  
Nitin G Valsange ◽  
Prakash P Wadgaonkar
Keyword(s):  
Acid Chloride ◽  
Phosphorus Oxychloride ◽  
Decomposition Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Good Thermal Stability ◽  
Flexible Films ◽  
Arylene Ether ◽  
Amorphous Nature

A new diacylhydrazide monomer, namely, 4-(4-(4-(4-(hydrazinocarbonyl)phenoxy)-2-pentadecylphenoxy)phenoxy) benzohydrazide (HPPDPB), was synthesized starting from 4-(4-hydroxyphenoxy)-3-pentadecylphenol. HPPDPB was polycondensed with terephthalic acid chloride (TPC), isophthalic acid chloride (IPC) and a mixture of TPC and IPC (50:50 mol%) to obtain polyhydrazides containing multiple arylene ether linkages in the backbone and pendent pentadecyl chains. Polyhydrazides were subsequently cyclized in the presence of phosphorus oxychloride to obtain the corresponding poly(1,3,4-oxadiazole)s. Polyhydrazides and poly(1,3,4-oxadiazole)s exhibited inherent viscosities in the range 0.65–0.72 dL g−1 and 0.54–0.62 dL g−1, respectively, which indicated the formation of reasonably high-molecular weight polymers. Polyhydrazides were soluble in polar aprotic solvents such as N,N-dimethylformamide, N,N-dimethylacetamide (DMAc), 1-methyl-2-pyrrolidinone and pyridine whereas poly(1,3,4-oxadiazole)s exhibited excellent solubility even in common organic solvents such as chloroform, dichloromethane and tetrahydrofuran. Tough, transparent and flexible films of polyhydrazides and poly(1,3,4-oxadiazole)s could be cast from DMAc and chloroform solutions, respectively. X-Ray diffraction studies revealed amorphous nature of polyhydrazides and poly(1,3,4-oxadiazole)s and the formation of layered structure was observed due to ordered packing of pentadecyl chains. The 10% decomposition temperature ( T10) values for poly(1,3,4-oxadiazole)s were in the range 425–440°C indicating their good thermal stability. Glass transition temperature ( Tg) values of polyhydrazides and poly(1,3,4-oxadiazole)s were in the range 175–192°C and 92–103°C, respectively. The excellent solubility characteristics and the large gap between Tg (92–103°C) and T10 (425–440°C) values give poly(1,3,4-oxadiazole)-containing pendent pentadecyl chains better opportunities for processability.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals Enhancement of Chloroprene/Natural/Butadiene Rubber Nanocomposite Properties Using Organoclays and Their Combination with Carbon Black as Fillers

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1085
Author(s):  
Patricia Castaño-Rivera ◽  
Isabel Calle-Holguín ◽  
Johanna Castaño ◽  
Gustavo Cabrera-Barjas ◽  
Karen Galvez-Garrido ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
High Performance ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rubber Blends ◽  
Ft Ir ◽  
Chloroprene Rubber

Organoclay nanoparticles (Cloisite® C10A, Cloisite® C15) and their combination with carbon black (N330) were studied as fillers in chloroprene/natural/butadiene rubber blends to prepare nanocomposites. The effect of filler type and load on the physical mechanical properties of nanocomposites was determined and correlated with its structure, compatibility and cure properties using Fourier Transformed Infrared (FT-IR), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and rheometric analysis. Physical mechanical properties were improved by organoclays at 5–7 phr. Nanocomposites with organoclays exhibited a remarkable increase up to 46% in abrasion resistance. The improvement in properties was attributed to good organoclay dispersion in the rubber matrix and to the compatibility between them and the chloroprene rubber. Carbon black at a 40 phr load was not the optimal concentration to interact with organoclays. The present study confirmed that organoclays can be a reinforcing filler for high performance applications in rubber nanocomposites.

scholarly journals The Potential for Natural Stones from Northeastern Brazil to Be Used in Civil Construction

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 440
Author(s):  
Fabiana Pereira da Costa ◽  
Jucielle Veras Fernandes ◽  
Luiz Ronaldo Lisboa de Melo ◽  
Alisson Mendes Rodrigues ◽  
Romualdo Rodrigues Menezes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Resistance ◽  
Mechanical Analysis ◽  
Northeastern Brazil ◽  
X Ray Diffraction ◽  
X Ray ◽  
Chemical Agents ◽  
Natural Stones

Natural stones (limestones, granites, and marble) from mines located in northeastern Brazil were investigated to discover their potential for use in civil construction. The natural stones were characterized by chemical analysis, X-ray diffraction, differential thermal analysis, and optical microscopy. The physical-mechanical properties (apparent density, porosity, water absorption, compressive and flexural strength, impact, and abrasion) and chemical resistance properties were also evaluated. The results of the physical-mechanical analysis indicated that the natural stones investigated have the potential to be used in different environments (interior, exterior), taking into account factors such as people’s circulation and exposure to chemical agents.

scholarly journals Functional Bionanocomposite Fibers of Chitosan Filled with Cellulose Nanofibers Obtained by Gel Spinning

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1563
Author(s):  
Sofia Marquez-Bravo ◽  
Ingo Doench ◽  
Pamela Molina ◽  
Flor Estefany Bentley ◽  
Arnaud Kamdem Tamo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Cellulose Nanofibers ◽  
Microstructural Characterization ◽  
Fiber Formation ◽  
Fiber Direction ◽  
Composite Fibers ◽  
X Ray Diffraction ◽  
Gel Spinning ◽  
X Ray

Extremely high mechanical performance spun bionanocomposite fibers of chitosan (CHI), and cellulose nanofibers (CNFs) were successfully achieved by gel spinning of CHI aqueous viscous formulations filled with CNFs. The microstructural characterization of the fibers by X-ray diffraction revealed the crystallization of the CHI polymer chains into anhydrous chitosan allomorph. The spinning process combining acidic–basic–neutralization–stretching–drying steps allowed obtaining CHI/CNF composite fibers of high crystallinity, with enhanced effect at incorporating the CNFs. Chitosan crystallization seems to be promoted by the presence of cellulose nanofibers, serving as nucleation sites for the growing of CHI crystals. Moreover, the preferential orientation of both CNFs and CHI crystals along the spun fiber direction was revealed in the two-dimensional X-ray diffraction patterns. By increasing the CNF amount up to the optimum concentration of 0.4 wt % in the viscous CHI/CNF collodion, Young’s modulus of the spun fibers significantly increased up to 8 GPa. Similarly, the stress at break and the yield stress drastically increased from 115 to 163 MPa, and from 67 to 119 MPa, respectively, by adding only 0.4 wt % of CNFs into a collodion solution containing 4 wt % of chitosan. The toughness of the CHI-based fibers thereby increased from 5 to 9 MJ.m−3. For higher CNFs contents like 0.5 wt %, the high mechanical performance of the CHI/CNF composite fibers was still observed, but with a slight worsening of the mechanical parameters, which may be related to a minor disruption of the CHI matrix hydrogel network constituting the collodion and gel fiber, as precursor state for the dry fiber formation. Finally, the rheological behavior observed for the different CHI/CNF viscous collodions and the obtained structural, thermal and mechanical properties results revealed an optimum matrix/filler compatibility and interface when adding 0.4 wt % of nanofibrillated cellulose (CNF) into 4 wt % CHI formulations, yielding functional bionanocomposite fibers of outstanding mechanical properties.

scholarly journals The crystal structures and mechanical properties of the uranyl carbonate minerals roubaultite, fontanite, sharpite, widenmannite, grimselite and čejkaite

2020 ◽  
Vol 7 (21) ◽  
pp. 4197-4221 ◽  
Author(s):  
Francisco Colmenero ◽  
Jakub Plášil ◽  
Jiří Sejkora
Keyword(s):  
Mechanical Properties ◽  
Hydrogen Bonding ◽  
Diffraction Pattern ◽  
Crystal Structures ◽  
First Principles ◽  
X Ray Diffraction ◽  
Carbonate Minerals ◽  
X Ray ◽  
Uranyl Carbonate

The structure, hydrogen bonding, X-ray diffraction pattern and mechanical properties of six important uranyl carbonate minerals, roubaultite, fontanite, sharpite, widenmannite, grimselite and čejkaite, are determined using first principles methods.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Sign in / Sign up

Export Citation Format

Share Document