Research on a probabilistic assessment method based on defective casing safety evaluation criteria in thermal recovery wells

2014 ◽  
Vol 228 (18) ◽  
pp. 3462-3470 ◽  
Author(s):  
XH Zhu ◽  
RQ Sun ◽  
H Tong
Keyword(s):  
Sensitivity Analysis ◽  
Evaluation Criteria ◽  
Safety Evaluation ◽  
Assessment Method ◽  
Thermal Recovery ◽  
Von Mises Stress ◽  
Probabilistic Assessment ◽  
Deterministic Approach ◽  
Corrosion Defects ◽  
Von Mises

Due to the fact that the complexity of loads and uncertainties of random variables affect the reliability of defective casings, with consideration to the disadvantages of the deterministic approach, in this paper a probabilistic assessment method is employed based on previously established safety evaluation criteria for casings with corrosion defects in thermal recovery wells. In addition, Monte Carlo simulation is proposed to analyze the casing reliability under different remaining strengths. Sensitivity analysis is then performed to rank the influence of various variables for casing failure, and finally the influence law of the main parameters on the maximum Von Mises stress of defective casing is summarized.

Study on the Residual Strength Assessment Method on Corroded Subsea Pipeline Based on Reference Stress Method

2009 ◽  
Author(s):  
Hui Li ◽  
Xiaobing Pan ◽  
Huilong Ren ◽  
Guoqing Feng
Keyword(s):  
Residual Strength ◽  
Assessment Method ◽  
Von Mises Stress ◽  
Strength Assessment ◽  
Subsea Pipeline ◽  
Reference Stress ◽  
Minimum Cross Section ◽  
Input Pressure ◽  
Von Mises ◽  
The Relationship

In this paper, the reference stress method is adopted in the residual strength assessment of corroded subsea pipeline. Through the monitoring of the von Mises stress σlocal in the minimum cross section, the relationship between the stress response and input pressure is found. Then, based on this relationship, a simple and effective method to assess the residual strength of corroded subsea pipeline is proposed. Through the comparison with experimental results, the accuracy and reliability of this method is confirmed.

scholarly journals Safety assessment of corrosion-defective natural gas pipeline under ground overload based on FEM

2021 ◽  
Vol 37 (1) ◽  
Author(s):  
T, Zheng ◽  
Z. Liang ◽  
J. Zhang ◽  
S. Tang ◽  
X. Xiao
Keyword(s):  
Internal Pressure ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Local Stress ◽  
Von Mises Stress ◽  
Stress And Strain ◽  
Failure Pressure ◽  
Corrosion Defect ◽  
Corrosion Defects ◽  
Von Mises

Aiming at the safety problem of the pipeline containing corrosion defects caused by ground overload, a novel method is developed to assess the safety of buried pipelines with corrosion defects and predict the failure pressure. The effects of parameters including internal pressure, ground overload, length of the loading area, corrosion defect depth, buried depth and soil Young’s modulus, are discussed. Ground overload greatly increases the von Mises stress and strain at the corrosion defect location and decreases the internal pressure threshold. The von Mises stress and strain are an obvious nonlinear relationship with internal pressure. The high stress and strain area expand along the diagonal direction of the defect area. The local stress and strain concentration at the corrosion defect increases with the increase of ground overload, length of the loading area and corrosion defect depth, which reduces the failure pressure of the pipeline. Increasing the buried depth and soil Young’s modulus would effectively reduce local stress and strain concentration, and increase the failure pressure of the pipeline. The pipeline settlement displacement increases with the increase of internal pressure, ground overload, length of the loading area, and decreases with the increase of pipeline buried depth and soil Young’s modulus.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

The Influence of Loading Position in A Priori High Stress Detection using Mode Superposition

2020 ◽  
Vol 1 (1) ◽  
pp. 93-102
Author(s):  
Carsten Strzalka ◽  
◽  
Manfred Zehn ◽  
Keyword(s):  
Finite Element ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
A Priori ◽  
High Stress ◽  
Von Mises Stress ◽  
Detailed Knowledge ◽  
Variable Loading ◽  
Numerical Effort ◽  
Von Mises

For the analysis of structural components, the finite element method (FEM) has become the most widely applied tool for numerical stress- and subsequent durability analyses. In industrial application advanced FE-models result in high numbers of degrees of freedom, making dynamic analyses time-consuming and expensive. As detailed finite element models are necessary for accurate stress results, the resulting data and connected numerical effort from dynamic stress analysis can be high. For the reduction of that effort, sophisticated methods have been developed to limit numerical calculations and processing of data to only small fractions of the global model. Therefore, detailed knowledge of the position of a component’s highly stressed areas is of great advantage for any present or subsequent analysis steps. In this paper an efficient method for the a priori detection of highly stressed areas of force-excited components is presented, based on modal stress superposition. As the component’s dynamic response and corresponding stress is always a function of its excitation, special attention is paid to the influence of the loading position. Based on the frequency domain solution of the modally decoupled equations of motion, a coefficient for a priori weighted superposition of modal von Mises stress fields is developed and validated on a simply supported cantilever beam structure with variable loading positions. The proposed approach is then applied to a simplified industrial model of a twist beam rear axle.

Research on Oil Depot Safety Evaluation Based on Dow Chemical Fire and Explosion Index Assessment Method

2013 ◽  
Vol 748 ◽  
pp. 1256-1261
Author(s):  
Shou Hui He ◽  
Han Hua Zhu ◽  
Shi Dong Fan ◽  
Quan Wen
Keyword(s):  
Production Management ◽  
Evaluation Method ◽  
Risk Index ◽  
Safety Evaluation ◽  
Assessment Method ◽  
Theoretical Ground ◽  
Potential Hazard ◽  
Process Unit ◽  
Safety Production ◽  
Fire And Explosion

At the present time, the Dow Chemical Fire and Explosion Index (F&EI) is a kind of risk index evaluation method that is comprehensively used in evaluating potential hazard, area of exposure, expected losses in case of fire and explosion, etc. As the research object to oil depot storage tank area, this article ultimately confirms establishing appropriate pattern of process unit as well as reasonable safety precautions compensating method, in order to insure the reasonableness of evaluating result, by means of selecting process unit, confirming material factor and compensating safety precautions, using F&EI method. This can provide the basis for theoretical ground in aspect of oil depot development and safety production management.

scholarly journals Numerical Investigation of the Deformable Porous Media Treated by the Intermittent Microwave

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 757
Author(s):  
Tianyi Su ◽  
Wenqing Zhang ◽  
Zhijun Zhang ◽  
Xiaowei Wang ◽  
Shiwei Zhang
Keyword(s):  
Porous Media ◽  
Heat Transport ◽  
Liquid Water ◽  
Von Mises Stress ◽  
Temperature Deformation ◽  
Local Maxima ◽  
Whole Process ◽  
Surface Areas ◽  
Pulse Ratio ◽  
Von Mises

A 2D axi-symmetric theoretical model of dielectric porous media in intermittent microwave (IMW) thermal process was developed, and the electromagnetic energy, multiphase transport, phase change, large deformation, and glass transition were taken into consideration. From the simulation results, the mass was mainly carried by the liquid water, and the heat was mainly carried by liquid water and solid. The diffusion was the dominant mechanism of the mass transport during the whole process, whereas for the heat transport, the convection dominated the heat transport near the surface areas during the heating stage. The von Mises stress reached local maxima at different locations at different stages, and all were lower than the fracture stress. A material treated by a longer intermittent cycle length with the same pulse ratio (PR) tended to trigger the phenomena of overheat and fracture due to the more intense fluctuation of moisture content, temperature, deformation, and von Mises stress. The model can be extended to simulate the intermittent radio frequency (IRF) process on the basis of which one can select a suitable energy source for a specific process.

scholarly journals Finite Element Analysis of Composite Repair for Damaged Steel Pipeline

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 301
Author(s):  
Jiaqi Chen ◽  
Hao Wang ◽  
Milad Salemi ◽  
Perumalsamy N. Balaguru
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Hoop Stress ◽  
Pipe Wall ◽  
Von Mises Stress ◽  
Repair System ◽  
Composite Repair ◽  
Steel Pipeline ◽  
Von Mises ◽  
Infill Material

Carbon fiber reinforced polymer (CFRP) matrix composite overwrap repair systems have been introduced and accepted as an alternative repair system for steel pipeline. This paper aimed to evaluate the mechanical behavior of damaged steel pipeline with CFRP repair using finite element (FE) analysis. Two different repair strategies, namely wrap repair and patch repair, were considered. The mechanical responses of pipeline with the composite repair system under the maximum allowable operating pressure (MAOP) was analyzed using the validated FE models. The design parameters of the CFRP repair system were analyzed, including patch/wrap size and thickness, defect size, interface bonding, and the material properties of the infill material. The results show that both the stress in the pipe wall and CFRP could be reduced by using a thicker CFRP. With the increase in patch size in the hoop direction, the maximum von Mises stress in the pipe wall generally decreased as the maximum hoop stress in the CFRP increased. The reinforcement of the CFRP repair system could be enhanced by using infill material with a higher elastic modulus. The CFRP patch tended to cause higher interface shear stress than CFRP wrap, but the shear stress could be reduced by using a thicker CFRP. Compared with the fully bonded condition, the frictional interface causes a decrease in hoop stress in the CFRP but an increase in von Mises stress in the steel. The study results indicate the feasibility of composite repair for damaged steel pipeline.

scholarly journals 3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

2021 ◽  
Vol 11 (6) ◽  
pp. 2547 ◽  
Author(s):  
Carlo Prati ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Alexandre Luiz Souto Borges ◽  
Maurizio Ventre ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Root Canal ◽  
Elastic Moduli ◽  
Reaction Force ◽  
Von Mises Stress ◽  
Elastic Behavior ◽  
Element Analysis ◽  
Heat Treated ◽  
Von Mises

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

scholarly journals Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Niksa Mohammadi Bagheri ◽  
Mahmoud Kadkhodaei ◽  
Shiva Pirhadi ◽  
Peiman Mosaddegh
Keyword(s):  
Clinical Data ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Average Error ◽  
Constant Thickness ◽  
Arc Length ◽  
Implementation Techniques ◽  
Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

Sign in / Sign up

Export Citation Format

Share Document