A numerical study on the blow-off limit of premixed hydrogen/air flames in a cylindrical micro-combustor

2020 ◽  
pp. 095441002097144
Author(s):  
Saeed Naeemi ◽  
Seyed Abdolmehdi Hashemi
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Flow Velocity ◽  
Equivalence Ratio ◽  
Numerical Study ◽  
Flame Stability ◽  
Convection Coefficient ◽  
Inlet Flow ◽  
Micro Combustor ◽  
Emissivity Coefficient

In the current work, a numerical study on combustion of premixed H2–air in a micro-cylindrical combustor was carried out and the critical velocity of inlet flow that causes the blow-off was obtained. Furthermore, the effects the equivalence ratio, wall thickness, geometry of combustor and thermal properties of walls on the critical blow-off velocity were studied. The numerical results showed that, increasing the equivalence ratio results in higher critical blow-off velocity. A micro combustor with thicker wall had better flame stability. As the combustor dimeter is decreased the blow-off occur in lower inlet flow velocity. Higher thermal conductivity of walls increases the critical blow-off velocity. In addition, with varying heat convection coefficient (h) and emissivity coefficient [Formula: see text] of the walls from 1 to 60 W/m2.K and 0.2 to 0.8 respectively, the critical blow-off velocity is reduced and shows the importance of wall thermal properties in the design and operation of micro-combustors.

scholarly journals Novel Dual Walling Cob Building: Dynamic Thermal Performance

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7663
Author(s):  
Kaoutar Zeghari ◽  
Ayoub Gounni ◽  
Hasna Louahlia ◽  
Michael Marion ◽  
Mohamed Boutouil ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Water Content ◽  
Wheat Straw ◽  
Numerical Study ◽  
Energy Performance ◽  
Climatic Conditions ◽  
Structural Walls ◽  
Hemp Shiv

This paper emphasizes the experimental and numerical study of new cob mixes used for insulation and load bearing wall elements. The experimental study provides complete datasets of thermal properties of the new walling materials, using cob with density ranging from 1107 kg/m3 to 1583 kg/m3 for structural walls and less than 700 kg m−3 for insulation walls. Various mixes of French soils and fibres (reed, wheat straw, hemp shiv, hemp straw, and flax straw) with different water contents are studied. The lowest average thermal conductivity is obtained for the structural cob mix prepared of 5% wheat straw and 31% of water content. The insulation mix, prepared with 25% reed and 31% water content, has the lowest thermal conductivity. Investigation of diffusivity, density, and heat capacity shows that, when thermal conductivity is lower than 0.4 W m−1 K−1, the decrease in cob density leads to better insulation values and higher heat capacity. Little variation is noticed regarding the density and heat capacity for cob mixes with thermal conductivity higher than 0.4 W m−1 K−1. Furthermore, the non-uniformity of local thermal conductivity and heat losses through the samples is due mainly to the non-uniform distribution of fibres inside the mixes inducing an increase in heat loss up to 50% for structural walls and 25% for insulation walls. Cob thermal properties are used in a comparative simulation case study of a typical house under French and UK climatic conditions. The energy performance of the conventional building is compared to a dual walled cob building, showing remarkable reduction in energy consumption as the cob walls, whilst maintaining comfortable indoor conditions without additional heating.

Effects of Groundwater Flow on a Ground Source Heat Pump System

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
Ayako Funabiki ◽  
Masahito Oguma
Keyword(s):  
Thermal Conductivity ◽  
Heat Flux ◽  
Groundwater Flow ◽  
Flow Velocity ◽  
Heat Pump ◽  
Numerical Study ◽  
High Thermal Conductivity ◽  
Ground Source Heat Pump ◽  
Pump System ◽  
Ground Source

Heat advection by groundwater flow is known to improve the performance of ground heat exchangers (GHEs), but the effect of groundwater advection on performance is not yet fully understood. This numerical study examined how parameters related to groundwater flow, such as aquifer thickness, porosity, lithology, and groundwater flow velocity, affected the performance of a borehole GHE. Under a thin-aquifer condition (10 m, or 10% of the entire GHE length in this study), groundwater flow velocity had the greatest effect on heat flux. At a groundwater flow velocity of at least 10−4 m/s through a low-porosity aquifer filled with granite gravel with high thermal conductivity, the heat flux of a GHE was as much as 60% higher than that of a GHE in a setting without an aquifer. If the aquifer was as thick as 50 m, the high thermal conductivity of granite gravel doubled the heat flux of the GHE at a groundwater flow velocity of at least 10−5 m/s. Thus, not only groundwater flow velocity but also aquifer thickness and thermal conductivity were important factors. However, groundwater seldom flows at such high velocities, and porosity, gravel size and composition, and aquifer thickness vary regionally. Thus, in the design of ground source heat pump systems, it is not appropriate to assume a large groundwater effect.

Numerical Study on Effect of Dimples on Tribo-Characteristics in Non-Newtonian Thermal Elastohydrodynamic Lubrication Point Contacts With Different Mechanical and Thermal Properties

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Motohiro Kaneta ◽  
Kenji Matsuda ◽  
Jing Wang ◽  
Peiran Yang
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Numerical Study ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Transient Behavior ◽  
Mechanical And Thermal Properties ◽  
Smooth Surfaces ◽  
Contact Surfaces ◽  
Micro Dimples

Abstract The transient behavior of tribo-characteristics caused by micro-dimples on point contact surfaces with different mechanical and thermal properties was investigated based on non-Newtonian thermal elastohydrodynamic lubrication (EHL) analysis. The dimples were assumed to exist on both contact surfaces and the surface shapes of the contact bodies were evaluated separately. It is pointed out that surface texturing due to the micro-dimples is not necessarily beneficial in EHL contacts under fully flooded conditions since the micro-dimples provide a high pressure and a thin minimum film thickness as compared with the case of contacts with smooth surfaces, although the friction coefficient of surfaces with micro-dimples is always lower than that of the smooth surfaces. In order to obtain relatively good tribo-characteristics, the velocity of the surface with low thermal conductivity should be faster than that with high thermal conductivity, and the wavelengths of micro-dimples in the direction of motion on both surfaces should be different.

Numerical study of the flame stability of premixed methane–air combustion in a combined porous-free flame burner

2018 ◽  
Vol 233 (4) ◽  
pp. 530-544 ◽  
Author(s):  
Seyed Mohammad Hashemi ◽  
Seyed Abdolmehdi Hashemi
Keyword(s):  
Equivalence Ratio ◽  
Numerical Study ◽  
Flame Stabilization ◽  
Pollutant Emissions ◽  
Pollutant Emission ◽  
Flame Stability ◽  
Emission Analysis ◽  
Porous Burner ◽  
Flame Burner ◽  
Stability Limits

Premixed methane–air combustion process within a combined porous-free flame burner was investigated numerically in the present study. The burner consisted of a perforated porous ceramic pellet forming combination of submerged and free flame zones. Nonequilibrium thermal condition between the gas and solid phases was implemented and governing equations were solved in a two-dimensional model using finite volume method. Detailed chemistry based on reduced GRI 3.0 mechanism with 41 reaction steps and 16 species including NOx mechanisms was utilized to simulate the combustion processes and pollutant emissions. In order to investigate the validation of the implemented numerical model, the burner was manufactured and tested. The predicted results were consistent with the experimental data. Comparison of the combined porous-free flame burner with porous burner showed that the flame stability limits of the combined burner were higher than those of porous burner. Multimode heat transfer within the porous medium was perused and the effect of heat recirculation on the flame stabilization was discussed. Investigation of the effect of pore density on the flame stabilization showed that the lower pore densities were desirable in order to improve the flame stability limits. Pollutant emission analysis proved that the NO concentration increased with increasing the equivalence ratio while the minimum quantity of CO concentration was evaluated at an equivalence ratio of 0.6.

Maximizing Heat Transfer Through Joint Fin Systems

2005 ◽  
Vol 128 (2) ◽  
pp. 203-206 ◽  
Author(s):  
A.-R. A. Khaled
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Thermal Performance ◽  
Critical Length ◽  
The Other ◽  
Rigid Fixation ◽  
Convection Coefficient ◽  
Heat Transfer Characteristics ◽  
Cold Side ◽  
Transfer Characteristics

Heat transfer through joint fins is modeled and analyzed analytically in this work. The terminology “joint fin systems” is used to refer to extending surfaces that are exposed to two different convective media from its both ends. It is found that heat transfer through joint fins is maximized at certain critical lengths of each portion (the receiver fin portion which faces the hot side and the sender fin portion that faces the cold side of the convective media). The critical length of each portion of joint fins is increased as the convection coefficient of the other fin portion increases. At a certain value of the thermal conductivity of the sender fin portion, the critical length for the receiver fin portion may be reduced while heat transfer is maximized. This value depends on the convection coefficient for both fin portions. Thermal performance of joint fins is increased as both thermal conductivity of the sender fin portion or its convection coefficient increases. This work shows that the design of machine components such as bolts, screws, and others can be improved to achieve favorable heat transfer characteristics in addition to its main functions such as rigid fixation properties.

Thermal Characterization of Carbon-Carbon Composites

2011 ◽  
Author(s):  
Messiha Saad ◽  
Darryl Baker ◽  
Rhys Reaves
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Critical Role ◽  
Carbon Composite ◽  
Flash Method ◽  
Carbon Composites ◽  
Energy Storage Devices ◽  
Graphitized Carbon

Thermal properties of materials such as specific heat, thermal diffusivity, and thermal conductivity are very important in the engineering design process and analysis of aerospace vehicles as well as space systems. These properties are also important in power generation, transportation, and energy storage devices including fuel cells and solar cells. Thermal conductivity plays a critical role in the performance of materials in high temperature applications. Thermal conductivity is the property that determines the working temperature levels of the material, and it is an important parameter in problems involving heat transfer and thermal structures. The objective of this research is to develop thermal properties data base for carbon-carbon and graphitized carbon-carbon composite materials. The carbon-carbon composites tested were produced by the Resin Transfer Molding (RTM) process using T300 2-D carbon fabric and Primaset PT-30 cyanate ester. The graphitized carbon-carbon composite was heat treated to 2500°C. The flash method was used to measure the thermal diffusivity of the materials; this method is based on America Society for Testing and Materials, ASTM E1461 standard. In addition, the differential scanning calorimeter was used in accordance with the ASTM E1269 standard to determine the specific heat. The thermal conductivity was determined using the measured values of their thermal diffusivity, specific heat, and the density of the materials.

scholarly journals Testing a Gypsum Composite Based on Raw Gypsum with a Direct Admixture of Paraffin and Polymer to Improve Thermal Properties

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3241
Author(s):  
Krzysztof Powała ◽  
Andrzej Obraniak ◽  
Dariusz Heim
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Phase Change ◽  
Large Scale ◽  
Building Materials ◽  
Residential Buildings ◽  
Energy Performance ◽  
Polymer Content ◽  
Volumetric Heat Capacity

The implemented new legal regulations regarding thermal comfort, the energy performance of residential buildings, and proecological requirements require the design of new building materials, the use of which will improve the thermal efficiency of newly built and renovated buildings. Therefore, many companies producing building materials strive to improve the properties of their products by reducing the weight of the materials, increasing their mechanical properties, and improving their insulating properties. Currently, there are solutions in phase-change materials (PCM) production technology, such as microencapsulation, but its application on a large scale is extremely costly. This paper presents a solution to the abovementioned problem through the creation and testing of a composite, i.e., a new mixture of gypsum, paraffin, and polymer, which can be used in the production of plasterboard. The presented solution uses a material (PCM) which improves the thermal properties of the composite by taking advantage of the phase-change phenomenon. The study analyzes the influence of polymer content in the total mass of a composite in relation to its thermal conductivity, volumetric heat capacity, and diffusivity. Based on the results contained in this article, the best solution appears to be a mixture with 0.1% polymer content. It is definitely visible in the tests which use drying, hardening time, and paraffin absorption. It differs slightly from the best result in the thermal conductivity test, while it is comparable in terms of volumetric heat capacity and differs slightly from the best result in the thermal diffusivity test.

Sign in / Sign up

Export Citation Format

Share Document