Mechanical properties and dimensional stability of jute/VER-isocyanate hybrid matrix composites

2021 ◽  
pp. 096739112110166
Author(s):  
Richa Singh ◽  
B Singh ◽  
M Gupta ◽  
VK Singh
Keyword(s):  
Mechanical Response ◽  
Matrix Material ◽  
Mechanical Analysis ◽  
Resin Matrix ◽  
Tensile Fracture ◽  
Matrix Composites ◽  
Hybrid Resin ◽  
Hybrid Matrix ◽  
Marginal Improvement ◽  
The Impact

Some composites of alkali treated jute fibers and vinylester-isocyanate/urethane hybrid resin were fabricated. The mechanical, thermo-mechanical, fractographic and aging behavior of these composites were studied and compared with the parent vinylester resin (VER) matrix composites. Using hybrid resin matrix, the impact strength of jute composites was increased by ∼20% over the VER matrix composites. It was, however, accompanied by the marginal improvement in their tensile and flexural properties. Dynamic mechanical analysis showed increased storage modulus and broadened tan δ peak when VER-isocyanate hybrid resin was used as a matrix material compared with the parent VER matrix in jute composites showing its superior stiffness and flexibility. In humid environment, a decrease in the weight gain and swelling thickness was observed for VER-isocyanate hybrid matrix jute composites after 60 days exposure when compared with the parent VER matrix composites. Under accelerated water aging, the drop of 12–24% in the tensile strength was noticed for VER-isocyanate hybrid matrix jute composites as compared to ∼29% for VER matrix composites. The changes in the mechanical response of all composites can be well co-related with their fractographic evidences existed onto the tensile fracture surfaces in both dry and wet conditions.

scholarly journals Viscoelastic Characterization of Short Fibres Reinforced Thermoplastic in Tension and Shearing

2010 ◽  
Vol 24-25 ◽  
pp. 419-423 ◽  
Author(s):  
A. Andriyana ◽  
Luisa Silva ◽  
Noelle Billon
Keyword(s):  
Mechanical Response ◽  
Polymer Matrix Composites ◽  
Mechanical Analysis ◽  
Integrated Modelling ◽  
Matrix Composites ◽  
Moulding Process ◽  
Permanent Strain ◽  
Mould Filling ◽  
Injection Moulding Process

The present work can be regarded as a first step toward an integrated modelling of mould filling during injection moulding process of polymer matrix composites and the resulting material behaviour under service loading conditions. More precisely, the emphasis of the present research is laid on the development of a mechanical model which takes into account the processing-induced microstructure and is capable to predict the mechanical response of the material. In the Part I, a set of experiments which captures the mechanical behaviour of an injection moulded short fibre reinforced under different strain histories is described. Three mechanical testing are conducted: Dynamic Mechanical Analysis (DMA), uniaxial tension and simple shear. Tests show that the material exhibits complex responses mainly due to non-linearity, anisotropy, time/rate-dependence, hysteresis and permanent strain. Moreover, the relaxed state of the material is characterized by the existence of a so-called anisotropic equilibrium hysteresis independently of the prescribed strain rate.

A Study on Low-Velocity Impact Characteristics and Compression Strength after Impact of Ceramic/Resin Matrix Composites

2010 ◽  
Vol 118-120 ◽  
pp. 226-230
Author(s):  
Xiang Zheng ◽  
Xiao Yan Tong ◽  
Hao Chen ◽  
Lei Jiang Yao
Keyword(s):  
Ceramic Matrix Composites ◽  
Ceramic Matrix ◽  
Low Velocity Impact ◽  
Resin Matrix ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Low Velocity ◽  
Velocity Impact ◽  
Impact Characteristics ◽  
The Impact

An experimental study of low-velocity impact characteristics and strength after impact was carried out on both woven fiber-reinforced resin matrix composites and woven fiber-reinforced ceramic matrix composites. The test specimens were impacted using a dropped-weight impact test apparatus with an instrumented spherical tip. Ultrasonic C-scan was used in nondestructive testing to characterize and quantify the impact damage. Much more damage of ceramic matrix composites than that of resin matrix composites occur and process in loading stage. The peak load of resin matrix composites is higher than that of ceramic matrix composites. According to the results of observing optical photographs and C-scan images, the damage area of ceramic matrix composites is greater than that of resin matrix composites and the difference increases as the energy increases. Damage resistance of ceramic matrix composites is lower than that of resin matrix composites, but damage tolerance of ceramic matrix composites is higher than that of resin matrix composites.

scholarly journals Effect of Metallic Additives to Polymer Matrix on Properties of Composite Adhesives Dedicated for Light Metal Joining

2017 ◽  
Vol 62 (4) ◽  
pp. 2287-2294 ◽  
Author(s):  
A. Mamala ◽  
P. Kwaśniewski ◽  
A. Nowak ◽  
J. Grzebinoga ◽  
W. Ściężor ◽  
...  
Keyword(s):  
Physical And Mechanical Properties ◽  
Light Metal ◽  
Resin Matrix ◽  
Matrix Composites ◽  
Solar Panels ◽  
Correct Operation ◽  
Photovoltaic Panel ◽  
Polymer Metal ◽  
Experimental Findings ◽  
The Impact

AbstractThe most recent and promising trends in development of renewable sources of energy are Combined Heat and Power (CHP) systems. The newest solutions from this field are hybrid compact solar panels. The correct operation of both systems, i.e. the photovoltaic panel and the heat exchanger requires an effective connection between the two. The adhesives utilized to interconnect above elements should provide a stable and hermetic joint able to withstand mechanical and thermal impacts of the surrounding environment factors. The paper presents the research results over the impact of the type and the amount of reinforcing phase on the physical and mechanical properties of epoxy resin matrix composites reinforced with particles of non-ferrous metals (Ag, Cu, W, Al), dedicated as adhesives for connections between photovoltaic panels and heat exchangers. Based on the experimental findings the usefulness of classical analytic models for valuation of polymer-metal composites properties was validated.

Thermoplastic/thermoset multilayer composites: A way to improve the impact damage tolerance of thermosetting resin matrix composites

2017 ◽  
Vol 171 ◽  
pp. 298-305 ◽  
Author(s):  
Camille Sonnenfeld ◽  
Hakima Mendil-Jakani ◽  
Romain Agogué ◽  
Philippe Nunez ◽  
Pierre Beauchêne
Keyword(s):  
Damage Tolerance ◽  
Impact Damage ◽  
Resin Matrix ◽  
Matrix Composites ◽  
Thermosetting Resin ◽  
Multilayer Composites ◽  
The Impact

Fabrication and characterization of SiC-reinforced Al-4032 metal matrix composites

2022 ◽  
Author(s):  
Pardeep Saini ◽  
Pradeep K. Singh
Keyword(s):  
Impact Toughness ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Low Cost ◽  
Matrix Material ◽  
Stir Casting ◽  
Optical Microscope ◽  
Matrix Composites ◽  
Sic Composites ◽  
The Impact

Abstract Aluminium metal matrix composites (AMCs) have become quite popular for light weight, low cost, and good workability. The present work reports the impact of silicon carbide (SiC) reinforcement on the physical, microstructural, and mechanical characteristics of Al-4032/SiC composites with 4, 6, 8% of SiC (particle size 54μm) fabricated through bottom pouring stir casting. Density and porosity measurements of all three AMCs have been performed using the rule of mixture. The microstructure of the AMC samples has been analyzed using an optical microscope (OM), x-ray diffraction analysis (XRD), and scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS). The mechanical properties, in terms of the ultimate tensile strength (UTS), elongation, micro-hardness, and impact toughness of the AMCs have also been obtained according to American society for testing and materials (ASTM) standards. A maximum 1.52% increase in theoretical density, while a maximum 2.92% decrease in experimental density has been recorded for 8% reinforcement. The UTS, microhardness, and impact toughness of the AMC have been found to improve significantly owing to the addition of ceramic particles. The uniform distribution of SiC particles all over base Al-4032 matrix material has been noticed by SEM and OM for AMCs up to 6% reinforcement.

Mechanical Characterization and Water Sorption in Polyester Matrix Composites Reinforced with Sisal Fiber: An Experimental Investigation

2016 ◽  
Vol 369 ◽  
pp. 131-134 ◽  
Author(s):  
D. Gomes dos Santos ◽  
A.G. Barbosa de Lima ◽  
M.V. Silva Pinto
Keyword(s):  
Water Sorption ◽  
Mechanical Characterization ◽  
Polymer Matrix Composites ◽  
Rectangular Cross Section ◽  
Unsaturated Polyester ◽  
Experimental Tests ◽  
Sisal Fiber ◽  
Resin Matrix ◽  
Matrix Composites ◽  
The Impact

In this work we evaluated the mechanical characterization and sorption water of polymer matrix composites reinforced with sisal fibers at different bath temperatures. Experimental tests of tensile (ASTM D 3039), impact (ASTM D 256) and water sorption in samples with rectangular cross section (dimensions of specimens 20x20mm) were made. It was used the unsaturated polyester resin matrix (Resapol 10-316). With the aim of analyzing the tensile strength and the impact, samples were made with fiber content (by weight) of 44.6%. Water sorption tests were performed with the specimens immersed in water at 25°C, 50°C and 70°C. The results showed that for higher water temperature less time the sample takes to reach saturation and mechanical properties is reduced.

Microstructural and Mechanical Behaviour Evaluation of Mg-Al-Zn Alloy Friction Stir Welded Joint

2020 ◽  
Vol 17 (3) ◽  
pp. 8150-8159
Author(s):  
Kulwant Singh ◽  
Gurbhinder Singh ◽  
Harmeet Singh
Keyword(s):  
Heat Treatment ◽  
Friction Stir Welding ◽  
Magnesium Alloys ◽  
Mechanical Performance ◽  
Fuel Efficiency ◽  
Research Work ◽  
Grain Structure ◽  
Tensile Fracture ◽  
Friction Stir ◽  
The Impact

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.

Optimization of Process Parameters in Stir Casting of Hybrid Metal Matrix (LM25/SiC/B4C) Composite Using Taguchi Method

2017 ◽  
Vol 13 (9) ◽  
pp. 6475-6479
Author(s):  
M. Arulraj ◽  
P.K. Palani ◽  
L. Venkatesh
Keyword(s):  
Taguchi Method ◽  
Matrix Material ◽  
Base Material ◽  
Stir Casting ◽  
Aluminium Matrix ◽  
Matrix Composites ◽  
Design Concepts ◽  
Specific Strength ◽  
Optimization Of Process Parameters ◽  
Reinforcement Material

Aluminium based composites exhibit many attractive material properties such as increased stiffness, wear resistance, specific strength and vibration damping and decreased co-efficient of thermal expansion compared with the conventional aluminium alloys. Aluminium Matrix Composites consist of non-metallic reinforcement which offers advantageous properties over base material. Reinforcements like SiC, B4C and Al2O3 are normally preferred to improve the mechanical properties. Here Aluminum LM25 is selected as matrix material while Silicon carbide and Boron carbide are selected as reinforcement material. The fabrication of aluminium matrix was done by stir casting method. In the present study an attempt has been made to investigate the effect of three major stir casting parameters (stir speed, stir duration and preheated temperature of reinforcement material) on stir casting of Aluminium LM25 - SiC - B4C composite. Experiments were conducted based on Taguchi methodology. Taguchi quality design concepts of L9 orthogonal array has been used to determine S/N ratio and through S/N ratio a set of optimum stir casting parameters were obtained. The experimental results confirmed the validity of Taguchi method for enhancing tensile strength of castings. 

Impact Strength, Flexural Modulus and Wear Rate of PMMA Composites Reinforced by Eggshell Powders

2020 ◽  
Vol 38 (7A) ◽  
pp. 960-966
Author(s):  
Aseel M. Abdullah ◽  
Hussein Jaber ◽  
Hanaa A. Al-Kaisy
Keyword(s):  
Impact Strength ◽  
Wear Rate ◽  
Flexural Modulus ◽  
Matrix Material ◽  
Weight Fraction ◽  
Pure Pmma ◽  
Calcination Process ◽  
The Matrix ◽  
The Impact ◽  
Interface Bond

In the present study, the impact strength, flexural modulus, and wear rate of poly methyl methacrylate (PMMA) with eggshell powder (ESP) composites have been investigated. The PMMA used as a matrix material reinforced with ESP at two different states (including untreated eggshell powder (UTESP) and treated eggshell powder (TESP)). Both UTESP and TESP were mixed with PMMA at different weight fractions ranged from (1-5) wt.%. The results revealed that the mechanical properties of the PMMA/ESP composites were enhanced steadily with increasing eggshell contents. The samples with 5 wt.% of UTESP and TESP additions give the maximum values of impact strength, about twice the value of the pure PMMA sample. The calcination process of eggshells powders gives better properties of the PMMA samples compared with the UTESP at the same weight fraction due to improvements in the interface bond between the matrix and particles. The wear characteristics of the PMMA composites decrease by about 57% with increases the weight fraction of TESP up to 5 wt.%. The flexural modulus values are slightly enhanced by increasing of the ESP contents in the PMMA composites.

Sign in / Sign up

Export Citation Format

Share Document