Numerical investigation of vortex-induced vibration for two tandem circular cylinders with different diameters

2020 ◽  
Vol 234 (3) ◽  
pp. 676-685
Author(s):  
Ming-ming Liu ◽  
Rui-jia Jin ◽  
Guo-qiang Tang ◽  
Cheng-yong Li
Keyword(s):  
Vortex Shedding ◽  
Vibration Amplitude ◽  
Stokes Equations ◽  
Euler Method ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Vortex Induced Vibration ◽  
Different Diameters ◽  
Vortex Shedding Modes

Vortex-induced vibration of two tandem circular cylinders with different diameters under low Reynolds number (Re = 200) is investigated numerically by solving the uncompressible two-dimensional Navier–Stokes equations. The arbitrary Lagrange–Euler method is used to simulate the movement of mesh. Effects of diameters and gap ratios are considered. Numerical results show that diameter ratios and gap ratios have little effect on maximum vibration amplitude. Four different vortex shedding modes are detected in this study.

Numerical Simulation of Oscillatory Flow Around Two Circular Cylinders of Different Diameters

2006 ◽  
Author(s):  
Hongwei An ◽  
Liang Cheng ◽  
Ming Zhao ◽  
Guohai Dong
Keyword(s):  
Experimental Data ◽  
Vortex Shedding ◽  
Oscillatory Flow ◽  
Stokes Equations ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Oscillatory Flows ◽  
Navier Stokes Equations ◽  
Different Diameters ◽  
Small Cylinder

A detailed study of oscillatory flow around two circular cylinders of different diameters is carried out numerically. The Reynolds-averaged Navier-Stokes equations are solved using a finite element method (FEM) with a k–ω turbulence closure. The numerical model is validated against oscillatory flows past a single circular cylinder where the experimental data are available in literature. Then it is employed to simulate the flow around two circular cylinders. It’s found that the fluid flow field around two cylinders is different from the single cylinder case, especially when the small cylinder diameter increases. The orientation of the small cylinder and the gap between two cylinders have significant effects on the vortex shedding process and force coefficients on the cylinders.

Vortex-Induced Vibration of Two Side-by-Side Circular Cylinders of Different Diameters in Close Proximity in Steady Flow

2012 ◽  
Author(s):  
Mehran Rahmanian ◽  
Liang Cheng ◽  
Ming Zhao ◽  
Tongming Zhou
Keyword(s):  
Natural Frequencies ◽  
Stokes Equations ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Stream Velocity ◽  
Arbitrary Lagrangian Eulerian ◽  
Navier Stokes Equations ◽  
Vortex Induced Vibrations ◽  
The Difference ◽  
Different Diameters

Vortex-induced vibrations of two side-by-side cylinders of different diameters in steady incompressible flow are studied. The diameter ratio of cylinders is fixed at 0.1. The Reynolds number is fixed at 5000 based on the large cylinder diameter and free stream velocity. A Petrov-Galerkin finite element method is used to solve the two dimensional Reynolds-averaged Navier Stokes equations using the Arbitrary Lagrangian Eulerian scheme with a SST k-ω turbulence model closure. The numerical method has been validated against available experimental results. Then, the effects of natural frequencies of the cylinders on the vibration amplitude and vortex shedding regimes are investigated. It is found that for the range of considered parameters, collision of the cylinders is dependent on the difference of the natural frequencies of the cylinders.

3D Simulation of Vortex Shedding Past Tapered Circular Cylinders in Subcritical Reynolds Numbers

2012 ◽  
Author(s):  
V. Tamimi ◽  
M. Zeinoddini ◽  
A. Bakhtiari ◽  
M. Golestani
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
High Reynolds

In this paper results from simulating the vortex shedding phenomena behind a fixed tapered circular cylinder, at relatively high Reynolds numbers, are reported. Ansys-CFX computational fluid dynamics model, based on solving three-dimensional (3D) incompressible transient Navier Stokes equations, is employed for this purpose. The geometries applied in the models resemble those used in wind tunnel experiments by other researchers. The taper slope along the cylinder span is uniform with a tangent of 24:1. The diameter at mid-span of the cylinder equals to 0.0389 m. The Reynolds number (based on the mid-span diameter) is around 29,000. The computational model has first been calibrated against experiments for uniform 3D cylinders as well as results from a Direct Numerical Simulation of turbulent wake with vortex shedding past a uniform circular cylinder, as obtained by other researchers. The main flow characteristics for tapered cylinders such as vortex dislocations and splitting, cellular vortex shedding, oblique vortex shedding and the variation of the vorticity patterns along the tapered cylinder could be obtained from the simulations.

Numerical Investigation of Flow Around Bluff Bodies

1998 ◽  
Vol 14 (3) ◽  
pp. 153-159 ◽  
Author(s):  
Chou-Jiu Tsai ◽  
Ger-Jyh Chen
Keyword(s):  
Vortex Shedding ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Bluff Bodies ◽  
Near Wake ◽  
Navier Stokes Equations ◽  
Physical Description ◽  
Geometrical Shapes ◽  
Flow Phenomena ◽  
Volume Method

ABSTRACTIn this study, fluid flow around bluff bodies are studied to examine the vortex shedding phenomenon in conjuction with the geometrical shapes of these vortex shedders. These flow phenomena are numerically simulated. A finite volume method is employed to solve the incompressible two-dimensional Navier-Stokes equations. Thus, quantitative descriptions of the vortex shedding phenomenon in the near wake were made, which lead to a detailed description of the vortex shedding mechanism. Streamline contours, figures of lift coefficent, and figures of drag coefficent in various time, are presented, respectively, for a physical description.

The turning couples on an elliptic particle settling in a vertical channel

1994 ◽  
Vol 271 ◽  
pp. 1-16 ◽  
Author(s):  
Peter Y. Huang ◽  
Jimmy Feng ◽  
Daniel D. Joseph
Keyword(s):  
Shear Stress ◽  
Vortex Shedding ◽  
Stokes Equations ◽  
Vertical Channel ◽  
Navier Stokes ◽  
Front Face ◽  
Two Dimensional ◽  
Navier Stokes Equations ◽  
Back Face ◽  
The One

We do a direct two-dimensional finite-elment simulation of the Navier–Stokes equations and compute the forces which turn an ellipse settling in a vertical channel of viscous fluid in a regime in which the ellipse oscillates under the action of vortex shedding. Turning this way and that is induced by large and unequal values of negative pressure at the rear separation points which are here identified with the two points on the back face where the shear stress vanishes. The main restoring mechanism which turns the broadside of the ellipse perpendicular to the fall is the high pressure at the ‘stagnation point’ on the front face, as in potential flow, which is here identified with the one point on the front face where the shear stress vanishes.

scholarly journals Propagation of Solitary Waves over a Submerged Slotted Barrier

2020 ◽  
Vol 8 (6) ◽  
pp. 419 ◽  
Author(s):  
Yun-Ta Wu ◽  
Shih-Chun Hsiao
Keyword(s):  
Flow Pattern ◽  
Solitary Waves ◽  
Vortex Shedding ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Model Data ◽  
Free Surface Elevation ◽  
Complex Flow ◽  
Laboratory Observation ◽  
Navier Stokes Equations

In this article, the interaction of solitary waves and a submerged slotted barrier is investigated in which the slotted barrier consists of three impermeable elements and its porosity can be determined by the distance between the two neighboring elements. A new experiment is conducted to measure free surface elevation, velocity, and turbulent kinetic energy. Numerical simulation is performed using a two-dimensional model based on the Reynolds-Averaged Navier-Stokes equations and the non-linear k-ɛ turbulence model. A detailed flow pattern is illustrated by a flow visualization technique. A laboratory observation indicates that flow separations occur at each element of the slotted barrier and the vortex shedding process is then triggered due to the complicated interaction of those induced vortices that further create a complex flow pattern. During the vortex shedding process, seeding particles that are initially accumulated near the seafloor are suspended by an upward jet formed by vortices interacting. Model-data comparisons are carried out to examine the accuracy of the model. Overall model-data comparisons are in satisfactory agreement, but modeled results sometimes fail to predict the positions of the induced vortices. Since the measured data is unique in terms of velocity and turbulence, the dataset can be used for further improvement of numerical modeling.

Validation of a Numerical Method for Unsteady Flow Calculations

1993 ◽  
Vol 115 (1) ◽  
pp. 110-117 ◽  
Author(s):  
M. Giles ◽  
R. Haimes
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Numerical Method ◽  
Stokes Equations ◽  
Companion Paper ◽  
Ideal Gas ◽  
Euler Method ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Loss Prediction

This paper describes and validates a numerical method for the calculation of unsteady inviscid and viscous flows. A companion paper compares experimental measurements of unsteady heat transfer on a transonic rotor with the corresponding computational results. The mathematical model is the Reynolds-averaged unsteady Navier–Stokes equations for a compressible ideal gas. Quasi-three-dimensionality is included through the use of a variable streamtube thickness. The numerical algorithm is unusual in two respects: (a) For reasons of efficiency and flexibility, it uses a hybrid Navier–Stokes/Euler method, and (b) to allow for the computation of stator/rotor combinations with arbitrary pitch ratio, a novel space–time coordinate transformation is used. Several test cases are presented to validate the performance of the computer program, UNSFLO. These include: (a) unsteady, inviscid flat plate cascade flows (b) steady and unsteady, viscous flat plate cascade flows, (c) steady turbine heat transfer and loss prediction. In the first two sets of cases comparisons are made with theory, and in the third the comparison is with experimental data.

CFD Analysis of Vortex Shedding in a Circular Cylinder: Flow Induced Vibration Design

2006 ◽  
Author(s):  
Nadeem Ahmed Sheikh ◽  
M. Afzaal Malik ◽  
Arshad Hussain Qureshi ◽  
M. Anwar Khan ◽  
Shahab Khushnood
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Stokes Equations ◽  
Boundary Layer Separation ◽  
The Body ◽  
Navier Stokes ◽  
Structural Vibrations ◽  
Flow Induced Vibration ◽  
Navier Stokes Equations ◽  
Implicit Approach

Flow past a blunt body, such as a circular cylinder, usually experiences boundary layer separation and very strong flow oscillations in the wake region behind the body at a discrete frequency that is correlated to the Reynolds number of the flow. The periodic nature of the vortex shedding phenomenon can sometimes lead to unwanted structural vibrations. The effect of vibrating instability of a single cylinder is investigated in a uniform flow using the power of computational methods. Fluid structure coupling procedure predicts the fluid forces responsible for structural vibrations. An implicit approach to the solution of the unsteady two-dimensional Navier-Stokes equations is used for computation of flow parameters. Calculations are performed in parallel using a domain re-meshing/deforming technique with efficient communication requirements. Results for the unsteady shedding flow behind a circular cylinder are presented with experimental comparisons, showing the feasibility of accurate, efficient, time-dependent estimation of shedding frequency and resulting vibrations.

Numerical Study of Oscillatory Flow Past Four Cylinders in Square Arrangement for Pitch Ratio Equal to 4

2011 ◽  
Author(s):  
P. Anagnostopoulos ◽  
Ch. Dikarou ◽  
S. A. Seitanis
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Central Line ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Constant Frequency ◽  
Navier Stokes Equations ◽  
Symmetry Of The Solution ◽  
Pitch Ratio ◽  
Two Sides

The results of a numerical study of the viscous oscillating flow around four circular cylinders are presented herein, for a constant frequency parameter, β, equal to 50, and Keulegan-Carpenter numbers, KC, ranging between 0.2 and 10. The cylinders were placed on the vertices of a square, whose two sides were perpendicular and two parallel to the oncoming flow, for a pitch ratio, P/D, equal to 4. The finite-element method was employed for the solution of the Navier-Stokes equations, in the formulation where the stream function and the vorticity are the field variables. The streamlines and the vorticity contours generated from the solution were used for the flow visualization. When the Keulegan-Carpenter number is lower than 4, the flow remains symmetrical with respect to the horizontal axis of symmetry of the solution domain and periodic at consecutive cycles. As KC increases to 4 the flow becomes aperiodic in different cycles, although symmetry with respect to the horizontal central line of the domain is preserved. For KC equal to 5 asymmetries appear intermittently in the flow, which are eventually amplified as KC increases still further. These asymmetries, in association with the aperiodicity at different cycles, lead to an almost chaotic configuration, as KC grows larger. For characteristic cases the flow pattern and the traces of the hydrodynamic forces are presented. In addition, the mean and r.m.s. values of the in-line and transverse forces and the hydrodynamic coefficients of the inline force were evaluated for the entire range of Keulegan-Carpenter numbers examined.

Numerical Calculation on Vortex-Induced Vibration of the Circular Cylinder Using Low Reynolds Model in Hybrid Method

2009 ◽  
Author(s):  
Xingwei Zhang ◽  
Chaoying Zhou
Keyword(s):  
Numerical Calculation ◽  
Finite Volume Method ◽  
Finite Volume ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Vortex Induced Vibration ◽  
Mesh Method ◽  
Volume Method

Fundamental research on interaction between flow and structure is presented for computation the fluid dynamics of different two-dimensional oscillating models. The Navier-Stokes equations are solved using finite volume method. A multigrid mesh method which was applied to the situation of flow past the stagnating or vibrating cylinder is developed to simulate this type of flow. The interactive results between flow and structure rigid cylinders have been present. The computation fluid dynamic codes mainly with low Reynolds RANS solver are used to solve the impressible viscous Navier-Stokes equations. Finite volume method which is coupled with conformal hybrid mesh method is developed to simulate this type of flow. Numerical investigation focused on the response and the fluid forces on the cylinders and also observed the different shedding model in the wake. The numerical results are compared in detail with recent experimental and computational work. Present numerical comparison also showed that solution using different turbulence model will make the result have a little discrepancy and each turbulence model has respective characteristics in numerical solution on the vortex-induced vibration of the cylinder. In addition, the formation of the 2P vortex shedding model through the lock-in region and the beginning of the shedding model transformation in numerical calculation from 2S model to 2P model has been analyzed.

Sign in / Sign up

Export Citation Format

Share Document