Friction Model between Shoes and Floor in Ballroom Dancing

2020 ◽  
Vol 2020 (0) ◽  
pp. C-2-1
Author(s):  
Tadashi SHIOYA
Keyword(s):  
Friction Model ◽  
Ballroom Dancing

Rubber–Road Contact: Comparison of Physics-Based Theory and Indoor Experiments

2016 ◽  
Vol 44 (3) ◽  
pp. 150-173 ◽  
Author(s):  
Mehran Motamedi ◽  
Saied Taheri ◽  
Corina Sandu
Keyword(s):  
Rough Surface ◽  
Practical Importance ◽  
Surface Profile ◽  
Surface Characteristics ◽  
Mechanical Analysis ◽  
Friction Model ◽  
Rubber Friction ◽  
Optical Profilometer ◽  
Viscoelastic Modulus ◽  
Longitudinal Slip

ABSTRACT For tire designers, rubber friction is a topic of pronounced practical importance. Thus, development of a rubber–road contact model is of great interest. In this research, to predict the effectiveness of the tread compound in a tire as it interacts with the pavement, the physics-based multiscale rubber-friction theories developed by B. Persson and M. Klüppel were studied. The strengths of each method were identified and incorporated into a consolidated model that is more comprehensive and proficient than any single, existing, physics-based approach. In the present work, the friction coefficient was estimated for a summer tire tread compound sliding on sandpaper. The inputs to the model were the fractal properties of the rough surface and the dynamic viscoelastic modulus of rubber. The sandpaper-surface profile was measured accurately using an optical profilometer. Two-dimensional parameterization was performed using one-dimensional profile measurements. The tire tread compound was characterized via dynamic mechanical analysis. To validate the friction model, a laboratory-based, rubber-friction test that could measure the friction between a rubber sample and any arbitrary rough surface was designed and built. The apparatus consisted of a turntable, which can have the surface characteristics of choice, and a rubber wheel in contact with the turntable. The wheel speed, as well as the turntable speed, could be controlled precisely to generate the arbitrary values of longitudinal slip at which the dynamic coefficient of friction was measured. The correlation between the simulation and the experimental results was investigated.

An Implicit to Explicit FEA Solving of Tire F&M with Detailed Tread Blocks

2012 ◽  
Vol 40 (2) ◽  
pp. 83-107 ◽  
Author(s):  
Zhao Li ◽  
Ziran R. Li ◽  
Yuanming M. Xia
Keyword(s):  
Test System ◽  
Mapping Method ◽  
Friction Model ◽  
Experimental Results ◽  
Slip Angle ◽  
Slip Ratio ◽  
The Road ◽  
Numerical Noise ◽  
Nonlinear Stress ◽  
Solving Strategy

ABSTRACT A detailed tire-rolling model (185/75R14), using the implicit to explicit FEA solving strategy, was constructed to provide a reliable, dynamic simulation with several modeling features, including mesh, material modeling, and a solving strategy that could contribute to the consideration of the serious numerical noises. High-quality hexahedral meshes of tread blocks were obtained with a combined mapping method. The actual rubber distributing and nonlinear, stress-strain relationship of the rubber and bilinear elastic reinforcement were modeled for realism. In addition, a tread-rubber friction model obtained from the Laboratory Abrasion and Skid Tester (LAT 100) was applied to simulate the interaction of the tire with the road. The force and moment (F&) behaviors of tire cornering when subjected to a slip-angle sweep of −10 to 10° were studied with that model. To demonstrate the efficiency of the proposed simulation, the computed F&M were compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering F&M agreed well with the experimental results, so the footprint shape and contact pressure distribution of several cornering conditions were investigated. Furthermore, the longitudinal forces in response to braking/driving torque application in a slip-ratio range of −100% to 100% were computed. The proposed FEA solution confines the numerical noise within a smaller range and can serve as a valid tool in tire design.

Reviews in Dynamic Characteristics of Rolling Interface and Vibration Test/Suppression Methods of Rolling Mill

2020 ◽  
Vol 14 ◽  
Author(s):  
Xiao-bin Fan ◽  
Hao Li ◽  
Yu Jiang ◽  
Bing-xu Fan ◽  
Liang-jing Li
Keyword(s):  
Dynamic Characteristics ◽  
Rolling Mill ◽  
Frequency Conversion ◽  
Vibration Suppression ◽  
Rolling Force ◽  
Rolling Process ◽  
Friction Model ◽  
Time Frequency ◽  
Roll Gap ◽  
Rolling Mill Vibration

Background: Rolling mill vibration mechanism is very complex, and people haven't found a satisfactory vibration control method. Rolling interface is one of the vibration sources of the rolling mill system, and its friction and lubrication state has a great impact on the vibration of the rolling mill system. It is necessary to establish an accurate friction model for unsteady lubrication process of roll gap and a nonlinear vibration dynamic model for rolling process. In addition, it is necessary to obtain more direct and real rolling mill vibration characteristics from the measured vibration signals, and then study the vibration suppression method and design the vibration suppression device. Methods: This paper summarizes the friction lubrication characteristics of rolling interface and its influence on rolling mill vibration, as well as the dynamic friction model of rolling interface, the tribological model of unsteady lubrication process of roll gap, the non-linear vibration dynamic model of rolling process, the random and non-stationary dynamic behavior of rolling mill vibration, etc. At the same time, the research status of rolling mill vibration testing technology and vibration suppression methods were summarized. Time-frequency analysis of non-stationary vibration signals was reviewed, such as wavelet transform, Wigner-Ville distribution, empirical mode decomposition, blind source signal extraction, rolling vibration suppression equipment development. Results: The lubrication interface of the roller gap under vibration state presents unsteady dynamic characteristics. The signals generated by the vibration must be analyzed in time and frequency simultaneously. In the aspect of vibration suppression of rolling mill, the calculation of inherent characteristics should be carried out in the design of rolling mill to avoid dynamic defects such as resonance. When designing or upgrading the mill structure, it is necessary to optimize the structure of the work roll bending and roll shifting system, such as designing and developing the automatic adjustment mechanism of the gap between the roller bearing seat and the mill stand, adding floating support device to the drum shaped toothed joint shaft, etc. In terms of rolling technology, rolling vibration can be restrained by improving roll lubrication, reasonably distributing rolling force of each rolling mill, reducing rolling force of vibration prone rolling mill, increasing entrance temperature, reducing rolling inlet tension, reducing strip outlet temperature and reasonably arranging roll diameter. The coupling vibration can also be suppressed by optimizing the hydraulic servo system and the frequency conversion control of the motor. Conclusion: Under the vibration state, the lubrication interface of roll gap presents unsteady dynamic characteristics. The signal generated by vibration must be analyzed by time-frequency distribution. In the aspect of vibration suppression of rolling mill, the calculation of inherent characteristics should be carried out in the design of rolling mill to avoid dynamic defects such as resonance. It is necessary to optimize the structure of work roll bending and roll shifting system when designing or reforming the mill structure. In rolling process, rolling vibration can be restrained by improving roll lubrication, reasonably distributing rolling force of each rolling mill, increasing billet temperature, reasonably arranging roll diameter and reducing rolling inlet tension. Through the optimization of the hydraulic servo system and the frequency conversion control of the motor, the coupling vibration can be suppressed. The paper has important reference significance for vibration suppression of continuous rolling mill and efficient production of high quality strip products.

Friction Force and Stresses Analysis for Contact of Assembled Details

2006 ◽  
Vol 113 ◽  
pp. 334-338
Author(s):  
Z. Dreija ◽  
O. Liniņš ◽  
Fr. Sudnieks ◽  
N. Mozga
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Plastic Deformation ◽  
Friction Force ◽  
Sliding Friction ◽  
Friction Model ◽  
Contact Interface ◽  
Finite Element Program ◽  
Elastic Plastic ◽  
Element Program

The present work deals with the computation of surface stresses and deformation in the presence of friction. The evaluation of the elastic-plastic contact is analyzed revealing three distinct stages that range from fully elastic through elastic-plastic to fully plastic contact interface. Several factors of sliding friction model are discussed: surface roughness, mechanical properties and contact load and areas that have strong effect on the friction force. The critical interference that marks the transition from elastic to elastic- plastic and plastic deformation is found out and its connection with plasticity index. A finite element program for determination contact analysis of the assembled details and due to details of deformation that arose a normal and tangencial stress is used.

scholarly journals Force-Free Control for Direct Teaching of a Surgical Assistant Robot End Effector with Wire-Driven Bidirectional Telescopic Mechanism

Sensors ◽  
2021 ◽  
Vol 21 (10) ◽  
pp. 3498
Author(s):  
Youqiang Zhang ◽  
Cheol-Su Jeong ◽  
Minhyo Kim ◽  
Sangrok Jin
Keyword(s):  
Control Algorithm ◽  
Position Control ◽  
Friction Model ◽  
Surgical Instruments ◽  
Control Input ◽  
End Effector ◽  
Motor Current ◽  
Direct Teaching ◽  
End Effectors ◽  
Teaching Operation

This paper shows the design and modeling of an end effector with a bidirectional telescopic mechanism to allow a surgical assistant robot to hold and handle surgical instruments. It also presents a force-free control algorithm for the direct teaching of end effectors. The bidirectional telescopic mechanism can actively transmit force both upwards and downwards by staggering the wires on both sides. In order to estimate and control torque via motor current without a force/torque sensor, the gravity model and friction model of the device are derived through repeated experiments. The LuGre model is applied to the friction model, and the static and dynamic parameters are obtained using a curve fitting function and a genetic algorithm. Direct teaching control is designed using a force-free control algorithm that compensates for the estimated torque from the motor current for gravity and friction, and then converts it into a position control input. Direct teaching operation sensitivity is verified through hand-guiding experiments.

scholarly journals Tire/Road Rolling Resistance Modeling: Discussing the Surface Macrotexture Effect

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 538
Author(s):  
Malal Kane ◽  
Ebrahim Riahi ◽  
Minh-Tan Do
Keyword(s):  
Slip Rate ◽  
Rolling Resistance ◽  
Friction Model ◽  
Slip Rates ◽  
Wide Range ◽  
Road Surfaces ◽  
Profile Depth ◽  
Experimental Rolling ◽  
Resistance Modeling ◽  
Pavement Friction

This paper deals with the modeling of rolling resistance and the analysis of the effect of pavement texture. The Rolling Resistance Model (RRM) is a simplification of the no-slip rate of the Dynamic Friction Model (DFM) based on modeling tire/road contact and is intended to predict the tire/pavement friction at all slip rates. The experimental validation of this approach was performed using a machine simulating tires rolling on road surfaces. The tested pavement surfaces have a wide range of textures from smooth to macro-micro-rough, thus covering all the surfaces likely to be encountered on the roads. A comparison between the experimental rolling resistances and those predicted by the model shows a good correlation, with an R2 exceeding 0.8. A good correlation between the MPD (mean profile depth) of the surfaces and the rolling resistance is also shown. It is also noticed that a random distribution and pointed shape of the summits may also be an inconvenience concerning rolling resistance, thus leading to the conclusion that beyond the macrotexture, the positivity of the texture should also be taken into account. A possible simplification of the model by neglecting the damping part in the constitutive model of the rubber is also noted.

scholarly journals A study on the vibration dissipation mechanism of the rotating blade with dovetail joint

2021 ◽  
pp. 146134842098533
Author(s):  
Chaofeng Li ◽  
Zengchuang Shen ◽  
Zilin Chen ◽  
Houxin She
Keyword(s):  
Dry Friction ◽  
Vibration Reduction ◽  
Friction Model ◽  
Rotating Speed ◽  
System Parameters ◽  
Tangential Stiffness ◽  
Damping Characteristics ◽  
Rotating Blade ◽  
Spatial Beam ◽  
Dissipation Mechanism

The vibration dissipation mechanism of the rotating blade with a dovetail joint is studied in this paper. Dry friction damping plays an indispensable role in the direction of vibration reduction. The vibration level is reduced by consuming the total energy of the turbine blade with the dry friction device on the blade-root in the paper. The mechanism of the vibration reduction is revealed by the variation of the friction force and the energy dissipation ratio of dry friction. In this paper, the flexible blade with a dovetail interface feature is discretized by using the spatial beam element based on the finite element theory. Then the classical Coulomb-spring friction model is introduced to obtain the dry friction model on the contact interfaces of the tenon-mortise structure. What is more, the effects of the system parameters (such as the rotating speed, the friction coefficient, the installation angle of the tenon) and the excitation level on blade damping characteristics are discussed, respectively. The results show that the variation of the system parameters leads to a significant change of damping characteristics of the blade. The variation of the tangential stiffness and the position of the external excitation will affect the nonlinear characteristics and vibration damping characteristics.

scholarly journals Asymmetric and chaotic responses of dry friction oscillators with different static and kinetic coefficients of friction

Meccanica ◽  
2021 ◽  
Author(s):  
Gábor Csernák ◽  
Gábor Licskó
Keyword(s):  
Dry Friction ◽  
Continuation Method ◽  
Friction Model ◽  
Lugre Friction Model ◽  
Kinetic Coefficients ◽  
Friction Oscillator ◽  
Lugre Friction ◽  
Friction Parameters ◽  
Two Parameter ◽  
Parameter Bifurcation

AbstractThe responses of a simple harmonically excited dry friction oscillator are analysed in the case when the coefficients of static and kinetic coefficients of friction are different. One- and two-parameter bifurcation curves are determined at suitable parameters by continuation method and the largest Lyapunov exponents of the obtained solutions are estimated. It is shown that chaotic solutions can occur in broad parameter domains—even at realistic friction parameters—that are tightly enclosed by well-defined two-parameter bifurcation curves. The performed analysis also reveals that chaotic trajectories are bifurcating from special asymmetric solutions. To check the robustness of the qualitative results, characteristic bifurcation branches of two slightly modified oscillators are also determined: one with a higher harmonic in the excitation, and another one where Coulomb friction is exchanged by a corresponding LuGre friction model. The qualitative agreement of the diagrams supports the validity of the results.

scholarly journals Study on Friction in Automotive Shock Absorbers Part 1: Friction Simulation Using a Dynamic Friction Model in the Contact Zone of an FEM Model

Vehicles ◽  
2021 ◽  
Vol 3 (2) ◽  
pp. 212-232
Author(s):  
Ludwig Herzog ◽  
Klaus Augsburg
Keyword(s):  
Ride Comfort ◽  
Viscous Friction ◽  
Simulation Method ◽  
Friction Model ◽  
Model Parameters ◽  
Dynamic Friction ◽  
Friction Modeling ◽  
Shock Absorbers ◽  
Operation Conditions ◽  
Wide Range

The important change in the transition from partial to high automation is that a vehicle can drive autonomously, without active human involvement. This fact increases the current requirements regarding ride comfort and dictates new challenges for automotive shock absorbers. There exist two common types of automotive shock absorber with two friction types: The intended viscous friction dissipates the chassis vibrations, while the unwanted solid body friction is generated by the rubbing of the damper’s seals and guides during actuation. The latter so-called static friction impairs ride comfort and demands appropriate friction modeling for the control of adaptive or active suspension systems. In this article, a simulation approach is introduced to model damper friction based on the most friction-relevant parameters. Since damper friction is highly dependent on geometry, which can vary widely, three-dimensional (3D) structural FEM is used to determine the deformations of the damper parts resulting from mounting and varying operation conditions. In the respective contact zones, a dynamic friction model is applied and parameterized based on the single friction point measurements. Subsequent to the parameterization of the overall friction model with geometry data, operation conditions, material properties and friction model parameters, single friction point simulations are performed, analyzed and validated against single friction point measurements. It is shown that this simulation method allows for friction prediction with high accuracy. Consequently, its application enables a wide range of parameters relevant to damper friction to be investigated with significantly increased development efficiency.

Sign in / Sign up

Export Citation Format

Share Document