Biodiesel Production from Kapok (Ceiba pentandra) Seed Oil using Naturally Alkaline Catalyst as an Effort of Green Energy and Technology

2013 ◽  
Vol 2 (3) ◽  
pp. 169-173 ◽  
Author(s):  
N.A. Handayani ◽  
H. Santosa ◽  
M. Sofyan ◽  
I. Tanjung ◽  
A. Chyntia ◽  
...  
Keyword(s):  
Seed Oil ◽  
Green Energy ◽  
Green Technology ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Alkaline Catalyst ◽  
Biodiesel Feedstock ◽  
Presidential Decree ◽  
Near Future

Nowadays, energy that used to serve all the needs of community, mainly generated from fossil (conventional energy). Terrace in energy consumption is not balanced with adequate fossil fuel reserves and will be totally depleted in the near future. Indonesian Government through a Presidential Decree No. 5 year 2006 mandates an increased capacity in renewable energy production from 5 percent to 15 percent in 2025. C. pentandra seed oil has feasibility as a sustainable biodiesel feedstock in Indonesia. The aim of this paper was to investigate biodiesel production from ceiba petandra seed oil using naturally potassium hydroxide catalyst. Research designs are based on factorial design with 2 levels and 3 independent variables (temperature, reaction time and molar ratio of methanol to oil). According to data calculation, the most influential single variable is molar ratio of methanol to oil. Characterization of biodiesel products meet all the qualifications standardized by SNI 04-7182-2006. Keywords: biodiesel, kapok seed oil, c. pentandra, green technology

scholarly journals Biodiesel Production from a Novel Nonedible Feedstock, Soursop (Annona muricata L.) Seed Oil

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2562 ◽  
Author(s):  
Chia-Hung Su ◽  
Hoang Nguyen ◽  
Uyen Pham ◽  
My Nguyen ◽  
Horng-Yi Juan
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Annona Muricata ◽  
Reaction Conditions ◽  
Biodiesel Feedstock ◽  
Acid Catalyzed ◽  
American Society ◽  
Optimal Reaction

This study investigated the optimal reaction conditions for biodiesel production from soursop (Annona muricata) seeds. A high oil yield of 29.6% (w/w) could be obtained from soursop seeds. Oil extracted from soursop seeds was then converted into biodiesel through two-step transesterification process. A highest biodiesel yield of 97.02% was achieved under optimal acid-catalyzed esterification conditions (temperature: 65 °C, 1% H2SO4, reaction time: 90 min, and a methanol:oil molar ratio: 10:1) and optimal alkali-catalyzed transesterification conditions (temperature: 65 °C, reaction time: 30 min, 0.6% NaOH, and a methanol:oil molar ratio: 8:1). The properties of soursop biodiesel were determined and most were found to meet the European standard EN 14214 and American Society for Testing and Materials standard D6751. This study suggests that soursop seed oil is a promising biodiesel feedstock and that soursop biodiesel is a viable alternative to petrodiesel.

Mango (Magnifera indica) seed oil grown in Dilla town as potential raw material for biodiesel production using NaOH- a homogeneous catalyst

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Seed Oil ◽  
Methyl Esters ◽  
Pollution Prevention ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Minimal Amount

Biodiesel produced by transesterification process from vegetable oils or animal fats is viewed as a promising renewable energy source. Now a day’s diminishing of petroleum reserves in the ground and increasing environmental pollution prevention and regulations have made searching for renewable oxygenated energy sources from biomasses. Biodiesel is non-toxic, renewable, biodegradable, environmentally benign, energy efficient and diesel substituent fuel used in diesel engine which contributes minimal amount of global warming gases such as CO, CO2, SO2, NOX, unburned hydrocarbons, and particulate matters. The chemical composition of the biodiesel was examined by help of GC-MS and five fatty acid methyl esters such as methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linoleneate were identified. The variables that affect the amount of biodiesel such as methanol/oil molar ratio, mass weight of catalyst and temperature were studied. In addition to this the physicochemical properties of the biodiesel such as (density, kinematic viscosity, iodine value high heating value, flash point, acidic value, saponification value, carbon residue, peroxide value and ester content) were determined and its corresponding values were 87 Kg/m3, 5.63 Mm2/s, 39.56 g I/100g oil, 42.22 MJ/Kg, 132oC, 0.12 mgKOH/g, 209.72 mgKOH/g, 0.04%wt, 12.63 meq/kg, and 92.67 wt% respectively. The results of the present study showed that all physicochemical properties lie within the ASTM and EN biodiesel standards. Therefore, mango seed oil methyl ester could be used as an alternative to diesel engine.

scholarly journals Biodiesel Production from Melia azedarach and Ricinus communis Oil by Transesterification Process

Catalysts ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 427 ◽  
Author(s):  
Muhammad Awais ◽  
Sa’ed A Musmar ◽  
Faryal Kabir ◽  
Iram Batool ◽  
Muhammad Asif Rasheed ◽  
...  
Keyword(s):  
Ricinus Communis ◽  
Cost Effective ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Melia Azedarach ◽  
Renewable Fuel ◽  
Animal Fats ◽  
Edible Crops ◽  
American Society

Biodiesel is a renewable fuel usually produced from vegetable oils and animal fats. This study investigates the extraction of oil and its conversion into biodiesel by base-catalyzed transesterification. Firstly, the effect of various solvents (methanol, n-hexane, chloroform, di-ethyl ether) on extraction of oil from non-edible crops, such as R. communis and M. azedarach, were examined. It was observed that a higher concentration of oil was obtained from R. communis (43.6%) as compared to M. azedarach (35.6%) by using methanol and n-hexane, respectively. The extracted oils were subjected to NaOH (1%) catalyzed transesterification by analyzing the effect of oil/methanol molar ratio (1:4, 1:6, 1:8 and 1:10) and varying temperature (20, 40, 60 and 80 °C) for 2.5 h of reaction time. M. azedarach yielded 88% and R. communis yielded 93% biodiesel in 1:6 and 1:8 molar concentrations at ambient temperature whereas, 60 °C was selected as an optimum temperature, giving 90% (M. azedarach) and 94% (R. communis) biodiesel. The extracted oil and biodiesel were characterized for various parameters and most of the properties fulfilled the American Society for Testing and Materials (ASTM) standard biodiesel. The further characterization of fatty acids was done by Gas Chromatography/Mass Spectrometer (GC/MS) and oleic acid was found to be dominant in M. azedarach (61.5%) and R. communis contained ricinoleic acid (75.53%). Furthermore, the functional groups were analyzed by Fourier Transform Infrared Spectroscopy. The results suggested that both of the oils are easily available and can be used for commercial biodiesel production at a cost-effective scale.

scholarly journals Optimization of Waste Cooking Oil’s FFA as Biodiesel Feedstock

Teknomekanik ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 14-21
Author(s):  
Sri Rizki Putri Primandari ◽  
Andril Arafat ◽  
Harumi Veny
Keyword(s):  
Irradiation Time ◽  
Control Variable ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Cooking Oil ◽  
Biodiesel Feedstock ◽  
Temperature Irradiation ◽  
Acid Esterification ◽  
Central Composite

Waste cooking oil has high Free Fatty Acid (FFA). It affected on decreasing a biodiesel production. FFA reduction is one of important processes in biodiesel production from waste cooking oil. Thus, this study aimed to examine the optimum condition in FFA reduction. The process is assisted by using ultrasonic irradiation on acid esterification. Variables of the process are acid concentration, molar ratio of methanol and oil, and irradiation time. Meanwhile temperature irradiation on 45oC is a control variable. Process optimization is conducted by Response Surface Methodology (RSM) with Central Composite Design (CCD). The optimum conditions of response were 7.22:1 (methanol to oil molar ratio), 0.92% wt H2SO4, 26.04 minutes (irradiation time), and 45oC (irradiation temperature). Ultrasonic system reduced FFA significantly compared to conventional method.

scholarly journals Biocatalytic Pickering Emulsions Stabilized by Lipase-Immobilized Carbon Nanotubes for Biodiesel Production

Catalysts ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 587 ◽  
Author(s):  
Lihui Wang ◽  
Xinlong Liu ◽  
Yanjun Jiang ◽  
Liya Zhou ◽  
Li Ma ◽  
...  
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
High Efficiency ◽  
Polynomial Equation ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Multiwall Carbon Nanotube ◽  
Pickering Emulsions ◽  
Optimum Reaction ◽  
Immobilized Candida Antarctica Lipase

Biodiesel is a promising renewable energy source that can replace fossil fuel, but its production is limited by a lack of high-efficiency catalysts for mass production and popularization. In this study, we developed a biocatalytic Pickering emulsion using multiwall carbon nanotube-immobilized Candida antarctica lipase B (CALB@PE) to produce biodiesel, with J. curcas L. seed oil and methanol as substrates. The morphology of CALB@PE was characterized in detail. A central composite design of the response surface methodology (CCD-RSM) was used to study the effects of the parameters on biodiesel yield, namely the amount of J. curcas L. seed oil (1.5 g), molar ratio of methanol to oil (1:1–7:1), CALB@PE dosage (20–140 mg), temperature (30–50 °C), and reaction time (0–24 h). The experimental responses were fitted with a quadratic polynomial equation, and the optimum reaction conditions were the methanol/oil molar ratio of 4.64:1, CALB@PE dosage of 106.87 mg, and temperature of 34.9 °C, with a reaction time of 11.06 h. A yield of 95.2%, which was basically consistent with the predicted value of 95.53%, was obtained. CALB@PE could be reused up to 10 times without a substantial loss of activity. CALB@PE exhibited better reusability than that of Novozym 435 in the process of biodiesel production.

scholarly journals Influence of Physicochemical Characteristics of Neem Seeds (Azadirachta indica A. Juss) on Biodiesel Production

Biomolecules ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 616
Author(s):  
Bakari Hamadou ◽  
Djomdi ◽  
Ruben Zieba Falama ◽  
Cedric Delattre ◽  
Guillaume Pierre ◽  
...  
Keyword(s):  
Seed Oil ◽  
Fatty Acid Content ◽  
Calorific Value ◽  
Acid Value ◽  
Physicochemical Characteristics ◽  
Biodiesel Production ◽  
Major Drawback ◽  
Neem Seed Oil ◽  
The City

The aim of this work is to study the influence of the physicochemical characteristics of neem seeds, according to their mass and oil content, on the production of biodiesel. After the physical characterization of the seeds and extraction of the oil (triglycerides), biodiesel was produced from crude neem seed oil by transesterification with ethanol in the presence of sodium hydroxide. This study shows that the physicochemical characteristics of these seeds vary according to the origin of the samples. The seeds from Zidim, with a mass average of 200 seeds evaluated at 141.36 g and an almond content of 40.70%, have better characteristics compared to those collected in the city of Maroua, with average values evaluated at 128.00 g and 36.05%, respectively. Almonds have an average lipid content of 53.98 and 56.75% for the Maroua and Zidim samples, respectively. This study also reveals that neem oil, by its physicochemical characteristics, has a satisfactory quality for a valorization in the production of biodiesel. However, its relatively high free fatty acid content is a major drawback, which leads to a low yield of biodiesel, evaluated on average at 89.02%, and requires a desacidification operation to improve this yield. The analysis of biodiesel indicates physicochemical characteristics close and comparable to those of petrodiesel, particularly in terms of calorific value, density, kinematic viscosity, acid value, evaluated at 41.00 MJ/kg, 0.803, 4.42 cSt, and 0.130 mg/g, respectively.

scholarly journals Biodiesel Production from Rubber Seed Oil via Esterification Process

2012 ◽  
Vol 1 (2) ◽  
pp. 57-60 ◽  
Author(s):  
Widayat Widayat ◽  
S Suherman
Keyword(s):  
Alternative Energy ◽  
Seed Oil ◽  
Raw Materials ◽  
Free Fatty Acid Level ◽  
Diesel Oil ◽  
Biodiesel Production ◽  
Rubber Seed Oil ◽  
Rubber Seed ◽  
Product Characterization

One promise source of alternative energy is biodiesel from rubber seed oil, because the raw materials available in plentiful quantities and can be renewed. In addition, the rubber seed is still lack of utilization, and Indonesia is one of the largest rubbers producing country in the world. The objective of this research is to studied on biodiesel production by esterification process. Parameters used in this study are the ratio of catalyst and temperature and its influence on the characteristics of the resulting biodiesel product. Characterization of rubber seed include acid content number analysis, saponification numbers, density, viscosity, iodine number, type of free fatty acids and triglyceride oils. The results of analysis showed that rubber seed oil content obtained is 50.5%. The results of the GCMS analysis showed that a free fatty acid level in rubber seed is very high. Conversion into bio-diesel oil is obtained by at most 59.91% and lowest 48.24%.

Biodiesel Production From Crude Rubber Seed Oil Using Supercritical Methanol Transesterification

2015 ◽  
Vol 781 ◽  
pp. 655-658 ◽  
Author(s):  
Thakun Sawiwat ◽  
Somjai Kajorncheappunngam
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Supercritical Methanol ◽  
Rubber Seed Oil ◽  
Promising Alternative ◽  
Rubber Seed ◽  
Biodiesel Synthesis

Synthesis of biodiesel from rubber seed oil using a supercritical methanol was investigated under various reaction conditions (220 - 300°C, 80 - 180 bar) with reaction time of 1-15 min and oil:methanol molar ratio of 1:20 - 1:60. Free fatty acid methyl esters (FAMEs) content were analyzed by gas chromatography-mass spectroscopy (GC-MS). Most properties of produced biodiesel were in good agreement with biodiesel standard (EN 14214). The maximum FAME yield of 86.90% was obtained at 260°C, 160 bar, 5 min reaction time using oil:methanol molar ratio of 1:40. The result showed the acid value of rubber seed oil decreased to 0.58 mgKOH/g from initial 24 mgKOH/g to. It could be concluded from this findings that crude rubber seed oil is a promising alternative raw material for biodiesel synthesis via supercritical methanol tranesterification.

Acidic Functionalized Nanobohemite: An Active Catalyst for Methyl Ester Production

2019 ◽  
Vol 17 (11) ◽  
Author(s):  
Shokoufe Hosseini ◽  
G. R. Moradi ◽  
Kiumars Bahrami
Keyword(s):  
Active Sites ◽  
Free Acid ◽  
Reaction Medium ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Optimal Point ◽  
Acidic Catalysts ◽  
Boehmite Nanoparticles ◽  
Optimized Conditions

Abstract In the biodiesel production, acidic catalysts are ideally suitable for reacting with different oil sources at various free acid levels. On the other hand, the nanocatalysts can easily be propagated in the reaction medium and provide more accessible active sites for reaction. The aim of this work was to synthesize an acidic nanocatalyst based on boehmite nanoparticles then studying it to biodiesel production from soybean oil. Up to now, no reports were found on biodiesel production by this catalyst. After the synthesis and characterization of the catalyst, using response surface methodology (RSM), the optimized conditions for transesterification were 4.87 wt.% for catalyst dosage, 13:1 for the molar ratio of methanol to oil, 60 °C for reaction temperature, and 3 h for reaction time. At the optimal point, the production yield was 99.8 %. After six consecutive use of the catalyst, the yield dropped slightly (88 %). Consequently, the catalyst can be employed efficiently several runs in the production process.

scholarly journals Optimization of Biodiesel Production Using Nanomagnetic CaO-Based Catalysts with Subcritical Methanol Transesterification of Rubber Seed Oil

Energies ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 230 ◽  
Author(s):  
Veronica Winoto ◽  
Nuttawan Yoswathana
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Acid Methyl Ester ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Optimum Conditions ◽  
Rubber Seed Oil ◽  
Box Behnken Design ◽  
Rubber Seed

The molar ratio of methanol to rubber seed oil (RSO), catalyst loading, and the reaction time of RSO biodiesel production were optimized in this work. The response surface methodology, using the Box–Behnken design, was analyzed to determine the optimum fatty acid methyl ester (FAME) yield. The performance of various nanomagnetic CaO-based catalysts—KF/CaO-Fe3O4, KF/CaO-Fe3O4-Li (Li additives), and KF/CaO-Fe3O4-Al (Al additives)—were compared. Rubber seed biodiesel was produced via the transesterification process under subcritical methanol conditions with nanomagnetic catalysts. The experimental results indicated that the KF/CaO-Fe3O4-Al nanomagnetic catalyst produced the highest FAME yield of 86.79%. The optimum conditions were a 28:1 molar ratio of methanol to RSO, 1.5 wt % catalyst, and 49 min reaction time. Al additives of KF/CaO-Fe3O4 nanomagnetic catalyst enhanced FAME yield without Al up to 18.17% and shortened the reaction time by up to 11 min.

Sign in / Sign up

Export Citation Format

Share Document