Removal of cobalt from aqueous solution containing EDTA under UV-C irradiation by antimony oxide

2016 ◽  
Vol 104 (6) ◽  
Author(s):  
Leena Malinen ◽  
Risto Koivula ◽  
Risto Harjula
Keyword(s):  
Antimony Oxide ◽  
Diffraction Field ◽  
Size Analysis ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Antimony Pentachloride ◽  
Simple Method ◽  
X Ray ◽  
Pore Size Analysis ◽  
Uv C

AbstractAntimony oxide was synthesized by a simple method involving the mixing of 6 M HCl and antimony pentachloride, adjusting the synthesis pH with 25% ammonia. The obtained material was characterized using X-ray diffraction, field emission scanning electron microscopy, and surface area and pore size analysis. The material structure resembled that of Sb

Temperature-controlled Deposition of Copper(I) Oxide and Metallic Copper Nanostructures from Single-source Molecular Precursor

2014 ◽  
Vol 67 (5) ◽  
pp. 757 ◽  
Author(s):  
Muhammad Shahid ◽  
Muhammad Mazhar ◽  
Asif Ali Tahir ◽  
Muhammad Khawar Rauf ◽  
James Raftery
Keyword(s):  
Thin Films ◽  
Metallic Copper ◽  
Chemical Vapour ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
Simple Method ◽  
X Ray ◽  
X Ray Crystallography ◽  
Glass Substrates ◽  
Controlled Deposition

A simple method of depositing morphology- and phase-tailored thin films of copper(i) oxide and metallic copper from [Cu(dmae)(TFA)]4·CH2Cl2 (1), where dmae is N,N-dimethylaminoethanolato and TFA is trifluoroacetato, on glass substrates by aerosol-assisted chemical vapour deposition is demonstrated. The tetrameric precursor 1 was synthesized and its structure was determined by single-crystal X-ray crystallography. Precursor 1 was applied for the deposition of nanostructured thin films of copper(i) oxide and copper nanowires at 250 and 375°C respectively. The deposited thin films were characterized by powder X-ray diffraction, field emission scanning electron microscopy, energy-dispersive X-ray diffraction, and ultraviolet–visible spectroscopy. The results indicate that the phase and morphology of the deposited material are strongly dependent on deposition temperature. UV-vis studies reveal that copper(i) oxide films with a band gap of 2.48 eV may find possible applications in tandem photoelectrochemical devices as light-absorbing material.

Selective catalytic reduction of NO by Co-Mn based nanocatalysts

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vahid Zabihi ◽  
Mohammad Hasan Eikani ◽  
Mehdi Ardjmand ◽  
Seyed Mahdi Latifi ◽  
Alireza Salehirad
Keyword(s):  
Selective Catalytic Reduction ◽  
Catalytic Reduction ◽  
Energy Dispersive ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Analysis Techniques ◽  
Acidic Sites ◽  
Temperature Window ◽  
Temperature Programmed

Abstract One of the most significant aspects in selective catalytic reduction (SCR) of nitrogen oxides (NOx) is developing suitable catalysts by which the process occurs in a favorable way. At the present work SCR reaction by ammonia (NH3-SCR) was conducted using Co-Mn spinel and its composite with Fe-Mn spinel, as nanocatalysts. The nanocatalysts were fabricated through liquid routes and then their physicochemical properties such as phase composition, degree of agglomeration, particle size distribution, specific surface area and also surface acidic sites have been investigated by X-ray diffraction, Field Emission Scanning Electron Microscope, Energy-dispersive X-ray spectroscopy, energy dispersive spectroscopy mapping, Brunauer–Emmett–Teller, temperature-programmed reduction (H2-TPR) and temperature-programmed desorption of ammonia (NH3-TPD) analysis techniques. The catalytic activity tests in a temperature window of 150–400 °C and gas hourly space velocities of 10,000, 18,000 and 30,000 h−1 revealed that almost in all studied conditions, CoMn2O4/FeMn2O4 nanocomposite exhibited better performance in SCR reaction than CoMn2O4 spinel.

scholarly journals Mining Wastes of an Albite Deposit as Raw Materials for Vitrified Mullite Ceramics

Minerals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 232
Author(s):  
Pedro J. Sánchez-Soto ◽  
Eduardo Garzón ◽  
Luis Pérez-Villarejo ◽  
George N. Angelopoulos ◽  
Dolores Eliche-Quesada
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Phase Evolution ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Mining Wastes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Value

In this work, an examination of mining wastes of an albite deposit in south Spain was carried out using X-ray Fluorescence (XRF), X-ray diffraction (XRD), particle size analysis, thermo-dilatometry and Differential Thermal Analysis (DTA) and Thermogravimetric (TG) analysis, followed by the determination of the main ceramic properties. The albite content in two selected samples was high (65–40 wt. %), accompanied by quartz (25–40 wt. %) and other minor minerals identified by XRD, mainly kaolinite, in agreement with the high content of silica and alumina determined by XRF. The content of Na2O was in the range 5.44–3.09 wt. %, being associated with albite. The iron content was very low (<0.75 wt. %). The kaolinite content in the waste was estimated from ~8 to 32 wt. %. The particle size analysis indicated values of 11–31 wt. % of particles <63 µm. The ceramic properties of fired samples (1000–1350 °C) showed progressive shrinkage by the thermal effect, with water absorption and open porosity almost at zero at 1200–1250 °C. At 1200 °C, the bulk density reached a maximum value of 2.38 g/cm3. An abrupt change in the phase evolution by XRD was found from 1150 to 1200 °C, with the disappearance of albite by melting in accordance with the predictions of the phase diagram SiO2-Al2O3-Na2O and the system albite-quartz. These fired materials contained as main crystalline phases quartz and mullite. Quartz was present in the raw samples and mullite was formed by decomposition of kaolinite. The observation of mullite forming needle-shape crystals was revealed by Scanning Electron Microscopy (SEM). The formation of fully densified and vitrified mullite materials by firing treatments was demonstrated.

scholarly journals Rapid four-component synthesis of dihydropyrano[2,3-c]pyrazoles using nano-eggshell/Ti(IV) as a highly compatible natural based catalyst

BMC Chemistry ◽  
2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Arefeh Dehghani Tafti ◽  
Bi Bi Fatemeh Mirjalili ◽  
Abdolhamid Bamoniri ◽  
Naeimeh Salehi
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Reaction Times ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solvent Free Conditions ◽  
High Yields ◽  
Work Up

AbstractNano-eggshell/Ti(IV) as a novel naturally based catalyst was prepared, characterized and applied for the synthesis of dihydropyrano[2,3-c]pyrazole derivatives. The characterization of nano-eggshell/Ti(IV) was performed using Fourier Transform Infrared spectroscopy, X-ray Diffraction, Field Emission Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, and Thermo Gravimetric Analysis. Dihydropyrano[2,3-c]pyrazoles were synthesized in the presence of nano-eggshell/Ti(IV) via a four component reaction of aldehydes, ethyl acetoacetate, malononitrile and hydrazine hydrate at room temperature under solvent free conditions. The principal affairs of this procedure are mild condition, short reaction times, easy work-up, high yields, reusability of the catalyst and the absence of toxic organic solvents.

Preparation of xanthated bentonite and its removal behavior for Pb(II) ions

2010 ◽  
Vol 61 (5) ◽  
pp. 1235-1243 ◽  
Author(s):  
Y. F. He ◽  
F. R. Li ◽  
R. M. Wang ◽  
F. Y. Li ◽  
Y. Wang ◽  
...  
Keyword(s):  
Adsorption Mechanism ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Particle Size Analysis ◽  
Lead Ions ◽  
Size Analysis ◽  
Optimum Conditions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Xanthate was successfully grafted onto bentonite by a relatively simple solution reaction. The obtained xanthated bentonite (XBent) was characterized by FT-IR spectrophotometer, thermogravimetric analysis (TG), particle size analysis, x-ray diffraction (XRD) and scanning electron microscopy (SEM). XBent acting as a type of environmentally friendly adsorbent was applied to remove lead ions from aqueous solutions. The optimum conditions were as follows: [Pb2 + ] = 500 mg L−1, [XBent] = 2 g L−1, pH = 5.0; oscillating 60 min under 200 rpm at 25°C. The removal rate of lead was up to 99.9%. It was found that the lead(II) ions—XBent adsorption isotherm model fitted well to the Freundlich isotherm. The adsorption mechanism was also investigated by SEM and XRD, which concluded that lead ions were complexed or chelated with XBent. XBent appears to have potential to be used later in water treatment as a type of inorganic polymer reagent.

Preparation of Visible-Light-Responsive TiO2-xNx Photocatalyst by a Very Simple Method

2011 ◽  
Vol 383-390 ◽  
pp. 3188-3191
Author(s):  
Han Jie Huang ◽  
Wen Long She ◽  
Ling Wen Yang ◽  
Hai Peng Huang
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflection ◽  
Ammonia Solution ◽  
Reflection Spectra ◽  
X Ray Diffraction ◽  
Simple Method ◽  
X Ray ◽  
Light Excitation

A visible-light-responsive TiO2-xNx photocatalyst was prepared by a very simple method. Ammonia solution was used as nitrogen resource in this paper. The TiO2-xNx photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), UV-Vis diffuse reflection spectra (DRS), and X-ray photoelectron spectroscopy (XPS). The ethylene was selected as a target pollutant under visible light excitation to evaluate the activity of this photocatalyst. The new prepared TiO2-xNx photocatalyst with strong photocatalytic activity under visible light irradiation was demonstrated in the experiment.

Synthesis of Alpha-Tricalcium Phosphate by Wet Reaction and Evaluation of Mechanical Properties

2012 ◽  
Vol 727-728 ◽  
pp. 1164-1169 ◽  
Author(s):  
Mônica Beatriz Thürmer ◽  
Rafaela Silveira Vieira ◽  
Juliana Machado Fernandes ◽  
Wilbur Trajano Guerin Coelho ◽  
Luis Alberto Santos
Keyword(s):  
Mechanical Properties ◽  
Calcium Phosphate ◽  
Tricalcium Phosphate ◽  
Calcium Nitrate ◽  
Chemical Precipitation ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcium Phosphate Cements

Calcium phosphate cements have bioactivity and osteoconductivity and can be molded and replace portions of bone tissue. The aim of this work was to study the obtainment of α-tricalcium phosphate, the main phase of calcium phosphate cement, by wet reaction from calcium nitrate and phosphoric acid. There are no reports about α-tricalcium phosphate obtained by this method. Two routes of chemical precipitation were evaluated and the use of two calcinations temperatures to obtain the phase of cement. The influence of calcination temperature on the mechanical properties of cement was evaluated. Cement samples were characterized by particle size analysis, X-ray diffraction, mechanical strength and scanning electron microscopy. The results demonstrate the strong influence of synthesis route on the crystalline phases of cement and the influence of concentration of reactants on the product of the reaction, as well as, on the mechanical properties of cement.

Growth mechanism and characterization of ZnO nano-tubes synthesized using the hydrothermal-etching method

2009 ◽  
Vol 63 (6) ◽  
Author(s):  
Yan Li ◽  
Chuan-Sheng Liu ◽  
Yun-Ling Zou
Keyword(s):  
Room Temperature ◽  
Morphological Analysis ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Etching Method ◽  
Nano Rods ◽  
Two Stages

AbstractZnO nano-tubes (ZNTs) have been successfully synthesized via a simple hydrothermal-etching method, and characterized by X-ray diffraction, field emission scanning electron microscopy and room temperature photoluminescence measurement. The as-synthesized ZNTs have a diameter of 500 nm, wall thickness of 20–30 nm, and length of 5 µm. Intensity of the plane (0002) diffraction peak, compared with that of plane (10$$ \bar 1 $$0) of ZNTs, is obviously lower than that of ZnO nano-rods. This phenomenon can be caused by the smaller cross section of plane (0002) of the nano-tubes compared with that of other morphologies. On basis of the morphological analysis, the formation process of nano-tubes can be proposed in two stages: hydrothermal growth and reaction etching process.

scholarly journals Synthesis of SnO2 Nanoparticles by High Potential Electrolysis

2017 ◽  
Vol 12 (2) ◽  
pp. 281 ◽  
Author(s):  
Fredy Kurniawan ◽  
Rahmi Rahmi
Keyword(s):  
Particle Size ◽  
Sno2 Nanoparticles ◽  
Particle Size Analysis ◽  
Reaction Engineering ◽  
High Potential ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanoparticles Synthesis ◽  
The Fourier Transform

SnO2 nanoparticles have been synthesized by high voltage electrolysis. Tin bare was used for anode and cathode. The effect of potentials and electrolyte were studied. The particles obtained after electrolysis was characterized using X-ray Diffraction (XRD). The diffractogram is in agreement with the standard diffraction pattern of SnO2 which is identified as tetragonal structure. The Fourier Transform Infrared (FTIR) spectrum indicates that there is a vibration of Sn–O asymmetric at 580 cm-1. The optimum potential for SnO2 nanoparticles synthesis is 60 V at 0.06 M HCl which shows the highest UV-Vis spectrum. The absorption peak of SnO2 nanoparticles by UV-Vis spectrophotometer appears at about 207 nm. The particle size analysis shows that the SnO2 nanoparticles obtained have the size distribution in a range of 25-150 nm with the highest volume at 83.11 nm. Copyright © 2017 BCREC Group. All rights reservedReceived: 15th November 2016; Revised: 26th February 2017; Accepted: 27th February 2017How to Cite: Rahmi, R., Kurniawan, F. (2017). Synthesis of SnO2 Nanoparticles by High Potential Electrolysis. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2): 281-286 (doi:10.9767/bcrec.12.2.773.281-286)Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.773.281-286 

The Evaporative Decomposition of Solutions Method (Eds) for the Production of Ultrafine Y1Ba2Cu3O7 from Nitrate and Mixed Anion Precursor Solutions

1989 ◽  
Vol 169 ◽  
Author(s):  
Rollin E. Lakis ◽  
Sidney R. Butler
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Barium Carbonate ◽  
Hollow Spheres ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

AbstractY1Ba2Cu3O7 has been prepared by the evaporative decomposition of solutions method. Nitrate and mixed anion solutions were atomized and decomposed at temperatures ranging from 300°C to 950°C. The resulting materials have been characterized using x-ray powder diffraction, Thermal Gravimetric Analysis (TGA), particle size analysis, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The powder consists of 0.3 micron agglomerated hollow spheres with a primary particle size of 0.06 micron. TGA and x-ray diffraction indicate the presence of barium nitrate and barium carbonate due to incomplete decomposition and/or product contamination by the process environment.

Sign in / Sign up

Export Citation Format

Share Document