scholarly journals Influence of the Hardener Proportion on Mechanical Properties of Adhesive Bonds Used in Agriculture

2015 ◽  
Vol 45 (4) ◽  
pp. 265-270 ◽  
Author(s):  
P. Valášek ◽  
M. Müller ◽  
J. Maleček
Keyword(s):  
Mechanical Properties ◽  
Production Process ◽  
Epoxy Resins ◽  
Adhesive Bonding ◽  
Variable Amount ◽  
Adhesive Bonds ◽  
Two Component ◽  
Agricultural Machines

Abstract Joining materials by adhesive bonding is used across all industrial branches. The occurrence of adhesive bonds in machine constructions is still more frequent because of the development of adhesives which are able to meet various requirements of designers. This trend is observable also in agriculture - in the construction of agricultural machines. There even exists a cooperation between the companies developing the adhesives and the agricultural machines producers. The production process of machines and equipment must consider a required production tact. Adhesives and the process of their hardening have to meet these requirements. In the sphere of agriculture, epoxy resins hardening based either on hardeners or heating are used. Mechanical properties of two-component epoxy resins depending on variable amount of the hardener starting crosslinking of these reactoplastics are described.

scholarly journals Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

10.14311/1835 ◽  
2013 ◽  
Vol 53 (4) ◽  
Author(s):  
Ivan Michalec ◽  
Milan Marônek
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Aluminium Alloy ◽  
Epoxy Resins ◽  
Adhesive Bonding ◽  
Thin Sheets ◽  
Two Component ◽  
Promising Area

Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals Study on mechanical properties of a new type of prefabricated GRC mold shell

2019 ◽  
Vol 136 ◽  
pp. 02030
Author(s):  
Chen Dong ◽  
Chen Ming ◽  
Cai Ouyang ◽  
Li Pengkun
Keyword(s):  
Mechanical Properties ◽  
Production Process ◽  
Cross Section ◽  
Stress System ◽  
Research Results ◽  
Floor Space ◽  
Section Size ◽  
Speed Up ◽  
New Type ◽  
Prefabricated Building

The GRC formwork structural column adopts the factory-based vertical prefabrication production process, which can reduce the floor space, reduce the formwork loss, speed up the construction progress, promote the full decoration of the prefabricated building, and improve the efficiency of the assembly construction. major. In order to optimize the production process of prefabricated GRC formwork column, the overall stress system of GRC formwork structure is analyzed in the concrete pouring process, and the thickness of GRC formwork, the number of steel hoops and the GRC mode are considered. The influence of the shell cross-section size on the mechanical properties. The research results can provide reference for the optimization and design of prefabricated GRC formwork column production process.

Experimental Assessment of Roughness Changes in the Cutting Surface and Microhardness Changes of the Material S 355 J2 G3 after Being Cut by Non-Conventional Technologies

2011 ◽  
Vol 314-316 ◽  
pp. 1944-1947 ◽  
Author(s):  
Jozef Maščeník ◽  
Stefan Gaspar
Keyword(s):  
Mechanical Properties ◽  
Production Process ◽  
Laser Plasma ◽  
Manufacturing Process ◽  
Production Quality ◽  
Water Jet ◽  
Cutting Edge ◽  
Experimental Assessment ◽  
Cutting Surface ◽  
The Impact

Production of components, necessary for the construction of the machine resp. or device is a demanding manufacturing process. One of the possibilities of increasing efficiency and production quality is the introduction of unconventional technologies to the production process. Knowing the dependence of the impact of non-conventional technologies on the mechanical properties of products and their subsequent verification is an important aspect when designing and manufacturing them. The article deals with the impact of used unconventional technology, that means laser, plasma and water jet on the roughness of a cutting edge and microhardness of material S 355 J2 G3.

scholarly journals Impact Modifiers and Compatibilizers for Versatile Epoxy-Based Adhesive Films with Curing and Deoxidizing Capabilities

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1129
Author(s):  
Bo-Young Lee ◽  
Dae-Hyeon Lee ◽  
Keon-Soo Jang
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resins ◽  
Film Formation ◽  
Electronic Devices ◽  
Amorphous Polymers ◽  
Acidic Group ◽  
Adhesive Film ◽  
Acidic Compounds ◽  
Semiconductor Packaging ◽  
Compatibilizing Agent

Epoxy resins with acidic compounds feature adhesion, robustness, and deoxidizing ability. In this study, hybrid adhesive films with deoxidizing and curing capabilities for semiconductor packaging were fabricated. The compatibilizing effects and mechanical properties were chiefly investigated by using various additive binders (thermoplastic amorphous polymers) and compatibilizing agents. The curing, deoxidizing, thermal, and rheological properties were systematically investigated. For uniform film formation and maximizing deoxidizing curable abilities, a thermoplastic--thermoset mixture containing a phenyl and carboxylic acid-based additive (benzoic acid), and a polycarbonate was chosen as the model adhesive film. Without either a phenyl or an acidic group in the compatibilizing agent, deoxidizing and compatibilizing effects were not achieved. The manufactured hybrid adhesive film can be effectively used, especially for electronic devices that require deoxidization and adhesion.

Development of technology for processing of chip wastes made of Al—Mg—Sc system alloy using hot extrusion method

2021 ◽  
pp. 123-129
Author(s):  
N.N. Zagirov ◽  
Yu.N. Loginov ◽  
E.V. Ivanov ◽  
V.G. Kuz’min
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Production Process ◽  
Liquid State ◽  
Hot Extrusion ◽  
Technological Scheme ◽  
System Alloy ◽  
Chip Processing ◽  
Extrusion Method

The problem of chip processing of aluminum alloy containing scandium is considered. The difficulty of remelting due to easy oxidation of the alloy components is noted. It is proposed to dispose of the shavings without transferring the metal to liquid state. The aim of the work is to construct technological scheme for the processing of waste chips of the Al—Mg—Sc alloy formed as result of machining cast billets by cutting. Results of experiments including cold briquetting, hot extrusion and drawing are presented. The mechanical properties of the product obtained according to several variants of the technological scheme are measured. The possibility of continuous drawing of semi-finished product is shown. The conclusion is made about the possibility of using the scheme in the production process.

Sign in / Sign up

Export Citation Format

Share Document