Metal Atom Routes to Metal-Based Clusters in Polymers

1988 ◽  
Vol 131 ◽  
Author(s):  
Mark P. Andrews ◽  
Mary E. Galvin ◽  
Sharon A. Heffner
Keyword(s):  
Polymer Composites ◽  
Metal Atom ◽  
Chemical Reduction ◽  
Incident Light ◽  
High Energy ◽  
Plasmon Mode ◽  
Ambient Temperatures ◽  
Metal Vapors ◽  
Precursor Molecules

ABSTRACTPast syntheses of polymer composites have largely evolved from chemical reduction or thermal decomposition of organometallic or inorganic precursor molecules in polymers, or plasma and thermal co-deposition of metal vapors and carbonaceous free radicals. Our approach involves the site-specific capture of metal atoms deposited in vacuum to give isolated, high energy mononuclear organometallic centers within a polymer film. These centers can be converted at ambient or sub-ambient temperatures (ie, below the polymer glass transition temperature) to, for example, metal oxide microclusters.We describe the results of our studies of a prototypical system involving chromium atoms and their conversion to corundum-type oxide microclusters in arene-functionalized polymer films. Thus Cr was deposited into 150 K liquid tetrahydrofuran solutions of polystyrene or poly(styrene-isoprene-styrene) triblock, spun in vacuo as thin films on the surface of a rotating glass cryostat. Evidence from epr spectrscopy shows that the resulting polymer-anchored (inter/intra-chain) bis(arene)Cr sandwich complex is locally mobile in the macroscopically rigid film at room temperature. The Cr atom is discharged from the rings by subsequent reaction with oxygen diffused into the film. Although α Cr2 O3 is a classic twosublevel antiferromagnet that is not epr active above 308 K, we observe an intense signal even at 77 K in these films. Cr2O3 microclusters are indicated, and these are confirmed by in situ measurements of the oxidation and aggregation process.The metal atom methodology has also been used to synthesize silver microsphere/polymer composites. With quadratic electrooptic phase modulation, these composites were found to show a third order susceptibility enhanced by coupling the dipolar surface plasmon mode of the particles with incident light.

In situ TEM studies of irradiation effects for materials improvement

1991 ◽  
Vol 49 ◽  
pp. 452-453
Author(s):  
Charles W. Allen
Keyword(s):  
Nuclear Reactor ◽  
Austenitic Stainless Steels ◽  
High Energy ◽  
Point Of View ◽  
In Situ Tem ◽  
Irradiation Effects ◽  
Tem Analysis ◽  
Radiation Induced ◽  
Analytical Tools

Irradiation effects studies employing TEMs as analytical tools have been conducted for almost as many years as materials people have done TEM, motivated largely by materials needs for nuclear reactor development. Such studies have focussed on the behavior both of nuclear fuels and of materials for other reactor components which are subjected to radiation-induced degradation. Especially in the 1950s and 60s, post-irradiation TEM analysis may have been coupled to in situ (in reactor or in pile) experiments (e.g., irradiation-induced creep experiments of austenitic stainless steels). Although necessary from a technological point of view, such experiments are difficult to instrument (measure strain dynamically, e.g.) and control (temperature, e.g.) and require months or even years to perform in a nuclear reactor or in a spallation neutron source. Consequently, methods were sought for simulation of neutroninduced radiation damage of materials, the simulations employing other forms of radiation; in the case of metals and alloys, high energy electrons and high energy ions.

In situ irradiation effects studies in medium- and high-voltage TEM

1995 ◽  
Vol 53 ◽  
pp. 234-235
Author(s):  
Charles W. Allen
Keyword(s):  
Cross Section ◽  
Particle Flux ◽  
Threshold Value ◽  
High Energy ◽  
Irradiation Damage ◽  
Defect Complexes ◽  
Lattice Position ◽  
Electrons And Ions ◽  
The Masses

With respect to structural consequences within a material, energetic electrons, above a threshold value of energy characteristic of a particular material, produce vacancy-interstial pairs (Frenkel pairs) by displacement of individual atoms, as illustrated for several materials in Table 1. Ion projectiles produce cascades of Frenkel pairs. Such displacement cascades result from high energy primary knock-on atoms which produce many secondary defects. These defects rearrange to form a variety of defect complexes on the time scale of tens of picoseconds following the primary displacement. A convenient measure of the extent of irradiation damage, both for electrons and ions, is the number of displacements per atom (dpa). 1 dpa means, on average, each atom in the irradiated region of material has been displaced once from its original lattice position. Displacement rate (dpa/s) is proportional to particle flux (cm-2s-1), the proportionality factor being the “displacement cross-section” σD (cm2). The cross-section σD depends mainly on the masses of target and projectile and on the kinetic energy of the projectile particle.

In situ TEM Studies of agglomeration of sub-nanometer Ru layers in Ru/C multilayers

1992 ◽  
Vol 50 (1) ◽  
pp. 256-257
Author(s):  
Tai D. Nguyen ◽  
Ronald Gronsky ◽  
Jeffrey B. Kortright
Keyword(s):  
Layered Structure ◽  
Driving Force ◽  
High Energy ◽  
Superior Performance ◽  
In Situ Tem ◽  
Rayleigh Instability ◽  
Practical Applications ◽  
Transmission Electron ◽  
Diffraction Patterns

Nanometer period Ru/C multilayers are one of the prime candidates for normal incident reflecting mirrors at wavelengths < 10 nm. Superior performance, which requires uniform layers and smooth interfaces, and high stability of the layered structure under thermal loadings are some of the demands in practical applications. Previous studies however show that the Ru layers in the 2 nm period Ru/C multilayer agglomerate upon moderate annealing, and the layered structure is no longer retained. This agglomeration and crystallization of the Ru layers upon annealing to form almost spherical crystallites is a result of the reduction of surface or interfacial energy from die amorphous high energy non-equilibrium state of the as-prepared sample dirough diffusive arrangements of the atoms. Proposed models for mechanism of thin film agglomeration include one analogous to Rayleigh instability, and grain boundary grooving in polycrystalline films. These models however are not necessarily appropriate to explain for the agglomeration in the sub-nanometer amorphous Ru layers in Ru/C multilayers. The Ru-C phase diagram shows a wide miscible gap, which indicates the preference of phase separation between these two materials and provides an additional driving force for agglomeration. In this paper, we study the evolution of the microstructures and layered structure via in-situ Transmission Electron Microscopy (TEM), and attempt to determine the order of occurence of agglomeration and crystallization in the Ru layers by observing the diffraction patterns.

Epitaxial growth manner and structure of superconducting oxide films

1990 ◽  
Vol 48 (4) ◽  
pp. 2-3
Author(s):  
Yoshichika Bando ◽  
Takahito Terashima ◽  
Kenji Iijima ◽  
Kazunuki Yamamoto ◽  
Kazuto Hirata ◽  
...  
Keyword(s):  
Ultrathin Films ◽  
Film Surface ◽  
High Energy ◽  
Epitaxial Films ◽  
Layer By Layer ◽  
Initial Growth ◽  
In Situ Growth ◽  
High Quality ◽  
Activated Reactive Evaporation

The high quality thin films of high-Tc superconducting oxide are necessary for elucidating the superconducting mechanism and for device application. The recent trend in the preparation of high-Tc films has been toward “in-situ” growth of the superconducting phase at relatively low temperatures. The purpose of “in-situ” growth is to attain surface smoothness suitable for fabricating film devices but also to obtain high quality film. We present the investigation on the initial growth manner of YBCO by in-situ reflective high energy electron diffraction (RHEED) technique and on the structural and superconducting properties of the resulting ultrathin films below 100Å. The epitaxial films have been grown on (100) plane of MgO and SrTiO, heated below 650°C by activated reactive evaporation. The in-situ RHEED observation and the intensity measurement was carried out during deposition of YBCO on the substrate at 650°C. The deposition rate was 0.8Å/s. Fig. 1 shows the RHEED patterns at every stage of deposition of YBCO on MgO(100). All the patterns exhibit the sharp streaks, indicating that the film surface is atomically smooth and the growth manner is layer-by-layer.

Transmission Electron Microscopy of Epitaxial silicides grown by ultra high vacuum deposition

1989 ◽  
Vol 47 ◽  
pp. 462-463
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Transmission Electron

The silicides CoSi2 and NiSi2 are both metallic with the fee flourite structure and lattice constants which are close to silicon (1.2% and 0.6% smaller at room temperature respectively) Consequently epitaxial cobalt and nickel disilicide can be grown on silicon. If these layers are formed by ultra high vacuum (UHV) deposition (also known as molecular beam epitaxy or MBE) their thickness can be controlled to within a few monolayers. Such ultrathin metal/silicon systems have many potential applications: for example electronic devices based on ballistic transport. They also provide a model system to study the properties of heterointerfaces. In this work we will discuss results obtained using in situ and ex situ transmission electron microscopy (TEM).In situ TEM is suited to the study of MBE growth for several reasons. It offers high spatial resolution and the ability to penetrate many monolayers of material. This is in contrast to the techniques which are usually employed for in situ measurements in MBE, for example low energy electron diffraction (LEED) and reflection high energy electron diffraction (RHEED), which are both sensitive to only a few monolayers at the surface.

Electron and ion irradiation-induced dissolution of mechanical twins in the intermetalic U3Si: An in situ HVEM study

1989 ◽  
Vol 47 ◽  
pp. 652-653
Author(s):  
Charles W. Allen ◽  
Robert C. Birtcher
Keyword(s):  
Elevated Temperatures ◽  
Ion Irradiation ◽  
Ion Beam ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Heavy Ion ◽  
High Energy ◽  
Mechanical Twinning ◽  
In Situ Experiments

The uranium silicides, including U3Si, are under study as candidate low enrichment nuclear fuels. Ion beam simulations of the in-reactor behavior of such materials are performed because a similar damage structure can be produced in hours by energetic heavy ions which requires years in actual reactor tests. This contribution treats one aspect of the microstructural behavior of U3Si under high energy electron irradiation and low dose energetic heavy ion irradiation and is based on in situ experiments, performed at the HVEM-Tandem User Facility at Argonne National Laboratory. This Facility interfaces a 2 MV Tandem ion accelerator and a 0.6 MV ion implanter to a 1.2 MeV AEI high voltage electron microscope, which allows a wide variety of in situ ion beam experiments to be performed with simultaneous irradiation and electron microscopy or diffraction.At elevated temperatures, U3Si exhibits the ordered AuCu3 structure. On cooling below 1058 K, the intermetallic transforms, evidently martensitically, to a body-centered tetragonal structure (alternatively, the structure may be described as face-centered tetragonal, which would be fcc except for a 1 pet tetragonal distortion). Mechanical twinning accompanies the transformation; however, diferences between electron diffraction patterns from twinned and non-twinned martensite plates could not be distinguished.

Modifications of a JEOL 2000EX TEM for insSitu surface studies

1993 ◽  
Vol 51 ◽  
pp. 640-641
Author(s):  
Michael T. Marshall ◽  
Xianghong Tong ◽  
J. Murray Gibson
Keyword(s):  
Electron Diffraction ◽  
Surface Science ◽  
Film Growth ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Transmission Electron ◽  
Fundamental Insight

We have modified a JEOL 2000EX Transmission Electron Microscope (TEM) to allow in-situ ultra-high vacuum (UHV) surface science experiments as well as transmission electron diffraction and imaging. Our goal is to support research in the areas of in-situ film growth, oxidation, and etching on semiconducter surfaces and, hence, gain fundamental insight of the structural components involved with these processes. The large volume chamber needed for such experiments limits the resolution to about 30 Å, primarily due to electron optics. Figure 1 shows the standard JEOL 2000EX TEM. The UHV chamber in figure 2 replaces the specimen area of the TEM, as shown in figure 3. The chamber is outfitted with Low Energy Electron Diffraction (LEED), Auger Electron Spectroscopy (AES), Residual Gas Analyzer (RGA), gas dosing, and evaporation sources. Reflection Electron Microscopy (REM) is also possible. This instrument is referred to as SHEBA (Surface High-energy Electron Beam Apparatus).The UHV chamber measures 800 mm in diameter and 400 mm in height. JEOL provided adapter flanges for the column.

Functional Poly(p-Xylylene)s via Chemical Reduction of Poly(p-Phenylene Vinylene)s

2019 ◽  
Author(s):  
Ain Uddin ◽  
Weifan Sang ◽  
Yong Gao ◽  
Kyle Plunkett
Keyword(s):  
Film Formation ◽  
Chemical Reduction ◽  
Water Soluble ◽  
Phenylene Vinylene ◽  
Polymer Modification ◽  
Polymer Backbone ◽  
Crosslinking Process ◽  
Conducting Membranes ◽  
In Situ Crosslinking

The synthesis of poly(p-xylylene)s (PPXs) with sidechains containing alkyl bromide functionality, and their post-polymer modification, is described. The PPXs were prepared by a diimide hydrogenation of poly(p-phenylene vinylene)s (PPVs) that were originally synthesized by a Gilch polymerization. The polymer backbone reduction was carried out with hydrazine hydrate in toluene at 80 °C to provide polymers with the sidechain-containing bromide functionality intact. To demonstrate post-polymer modification of the sidechains, the resulting PPX polymers were modified with trimethylamine to form tetraalkylammonium ion functionality and were evaluated as anion conducting membranes. While PPX homopolymers containing tetralkylammonium ions were completely water soluble and not able to form valuable films, PPX copolymers containing mixed tetraalkylammonium ions and hydrophobic chains were capable of film formation and alkaline stability. In addition, an in situ crosslinking process that used N,N,N',N'-tetramethyl-1,6-hexanediamine during the tetraalkylammonium formation of brominated PPX polymers was also evaluated and gave reasonable films with conductivities of ~10 mS-cm-1.

Functional Poly(p-Xylylene)s via Chemical Reduction of Poly(p-Phenylene Vinylene)s

2019 ◽  
Author(s):  
Ain Uddin ◽  
Weifan Sang ◽  
Yong Gao ◽  
Kyle Plunkett
Keyword(s):  
Film Formation ◽  
Chemical Reduction ◽  
Water Soluble ◽  
Phenylene Vinylene ◽  
Polymer Modification ◽  
Polymer Backbone ◽  
Crosslinking Process ◽  
Conducting Membranes ◽  
In Situ Crosslinking

The synthesis of poly(p-xylylene)s (PPXs) with sidechains containing alkyl bromide functionality, and their post-polymer modification, is described. The PPXs were prepared by a diimide hydrogenation of poly(p-phenylene vinylene)s (PPVs) that were originally synthesized by a Gilch polymerization. The polymer backbone reduction was carried out with hydrazine hydrate in toluene at 80 °C to provide polymers with the sidechain-containing bromide functionality intact. To demonstrate post-polymer modification of the sidechains, the resulting PPX polymers were modified with trimethylamine to form tetraalkylammonium ion functionality and were evaluated as anion conducting membranes. While PPX homopolymers containing tetralkylammonium ions were completely water soluble and not able to form valuable films, PPX copolymers containing mixed tetraalkylammonium ions and hydrophobic chains were capable of film formation and alkaline stability. In addition, an in situ crosslinking process that used N,N,N',N'-tetramethyl-1,6-hexanediamine during the tetraalkylammonium formation of brominated PPX polymers was also evaluated and gave reasonable films with conductivities of ~10 mS-cm-1.

scholarly journals B0AT1 amino acid transporter complexed with SARS-CoV-2 receptor ACE2 forms a heterodimer functional unit: in situ conformation using radiation inactivation analysis

Function ◽  
2021 ◽  
Author(s):  
Bruce R Stevens ◽  
J Clive Ellory ◽  
Robert L Preston
Keyword(s):  
Amino Acid ◽  
Membrane Trafficking ◽  
Functional Unit ◽  
Membrane Vesicles ◽  
High Energy ◽  
Amino Acid Transporter ◽  
Neutral Amino Acid ◽  
Transport Activity ◽  
Acid Transporter

Abstract The SARS-CoV-2 receptor, Angiotensin Converting Enzyme-2 (ACE2), is expressed at levels of greatest magnitude in the small intestine as compared to all other human tissues. Enterocyte ACE2 is co-expressed as the apical membrane trafficking partner obligatory for expression and activity of the B0AT1 sodium-dependent neutral amino acid transporter. These components are assembled as an [ACE2: B0AT1]2 dimer-of-heterodimers quaternary complex that putatively steers SARS-CoV-2 tropism in the gastrointestinal (GI) tract. GI clinical symptomology is reported in about half of COVID-19 patients, and can be accompanied by gut shedding of virion particles. We hypothesized that within this 4-mer structural complex, each [ACE2: B0AT1] heterodimer pair constitutes a physiological “functional unit.” This was confirmed experimentally by employing purified lyophilized enterocyte brush border membrane vesicles that were exposed to increasing doses of high-energy electron radiation from a 16 MeV linear accelerator. Based on established target theory, the results indicated the presence of Na+-dependent neutral amino acid influx transport activity functional unit with target size mw = 183.7 ± 16.8 kDa in situ in intact apical membranes. Each thermodynamically stabilized [ACE2: B0AT1] heterodimer functional unit manifests the transport activity within the whole ∼345 kDa [ACE2: B0AT1]2 dimer-of-heterodimers quaternary structural complex. The results are consistent with our prior molecular docking modeling and gut-lung axis approaches to understanding COVID-19. These findings advance the understanding of the physiology of B0AT1 interaction with ACE2 in the gut, and thereby potentially contribute to translational developments designed to treat or mitigate COVID-19 variant outbreaks and/or GI symptom persistence in long-haul Post-Acute Sequelae of SARS-CoV-2 (PASC).

Sign in / Sign up

Export Citation Format

Share Document