Temperature Control and Temperature Uniformity During Rapid Thermal Processing

1991 ◽  
Vol 224 ◽  
Author(s):  
Peter Vandenabeele ◽  
Karen Maex
Keyword(s):  
Temperature Control ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Temperature Uniformity ◽  
Chamber Design

AbstractAn overview is given of the major problems in temperature control and uniformity control. For temperature control varying emissivity due to layers, roughness, doping and chamber design are discussed, together with problems due to lamp radiation. The main way to go seems to be in-situ emissivity correction. For uniformity control, the main problems are non-uniform reflector radiation and patteren induced non-uniformity. The solution seems to be the design of a reflective chamber with uniform reflected radiation.

Temperature Monitoring by Ripple Pyrometry in Rapid Thermal Processing

1996 ◽  
Vol 429 ◽  
Author(s):  
Binh Nguyenphu ◽  
Minseok Oh ◽  
Anthony T. Fiory
Keyword(s):  
Temperature Control ◽  
Integrated Circuit ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Back Side ◽  
Integrated Circuit Manufacturing ◽  
Current Trends ◽  
Processing Steps ◽  
Electrical Data

AbstractCurrent trends of silicon integrated circuit manufacturing demand better temperature control in various thermal processing steps. Rapid thermal processing (RTP) has become a key technique because its single wafer process can accommodate the reduced thermal budget requirements arising from shrinking the dimensions of devices and the trend to larger wafers. However, temperature control by conventional infrared pyrometry, which is highly dependent on wafer back side conditions, is insufficiently accurate for upcoming technologies. Lucent Technologies Inc., formerly known as AT&T Microelectronics and AT&T Bell Laboratories, has developed a powerful real-time pyrometry technique using the A/C ripple signal from heating lamps for in-situ temperature measurement. Temperature and electrical data from device wafers have been passively collected by ripple pyrometers in three RTP systems and analyzed. In this paper we report the statistical analysis of ripple temperature and electrical data from device wafers for a typical implant anneal process temperature range of 900 to 1000 °C.

In-Situ Temperature Control for Rtp Via Thermal Expansion Measurement

1993 ◽  
Vol 303 ◽  
Author(s):  
Bruce Peuse ◽  
Allan Rosekrans
Keyword(s):  
Thermal Expansion ◽  
Temperature Control ◽  
Measurement Technique ◽  
Preliminary Data ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Processing System ◽  
Wafer Temperature ◽  
Thermal Expansion Measurement

ABSTRACTA new method of temperature control for rapid thermal processing of silicon wafers is presented whereby in-situ wafer temperature is determined by measurement of wafer thermal expansion via an optical micrometer mechanism. The expansion measurement technique and its implementation into a rapid thermal processing system for temperature control are described. Preliminary data show the wafer to wafer temperature repeatability to be 1% (3-σ) using this technique.

Temperature Uniformity Optimization Using Three-Zone Lamp and Dynamic Control in Rapid Thermal Multiprocessor

1991 ◽  
Vol 224 ◽  
Author(s):  
Pushkar P. Apte ◽  
Samuel Wood ◽  
Len Booth ◽  
Krishna C. Saraswat ◽  
Mehrdad M. Moslehi
Keyword(s):  
Thermal Processing ◽  
Dynamic Control ◽  
Rapid Thermal Processing ◽  
Chemical Vapor ◽  
Processing Conditions ◽  
Temperature Uniformity ◽  
Throughput Rate ◽  
Precise Control ◽  
Lamp System

AbstractRapid thermal processing (RTP) can play an important role in in situ single-wafer thermal multiprocessing, since it allows for a rapid wafer throughput rate. Conventional dedicated RTP equipment, where temperature uniformity is achieved by optimized reflector and chamber geometries for a specific process, typically cannot provide uniformity for different processes, or for a range of processing conditions. In this work we present a new flexible lamp system, in which tungsten-halogen lamps are configured in three concentric rings that are independently and dynamically controlled. The resultant circularly symmetric flux, which can be varied and controlled both temporally and spatially, offers significantly improved temperature uniformity. This is demonstrated using thermocouples as well as actual processes such as implant annealing, thermal oxidation and chemical vapor deposition of silicon. Through added flexibility and more precise control, this approach offers a powerful tool for multiprocessing and rapid process prototyping.

Monte Carlo Thermal Model of an Integrating Light Pipe for Rapid Thermal Processing

1996 ◽  
Vol 429 ◽  
Author(s):  
J. C. Thomas ◽  
D. P. Dewitt
Keyword(s):  
Monte Carlo ◽  
Thermal Processing ◽  
Monte Carlo Model ◽  
Rapid Thermal Processing ◽  
Width Ratio ◽  
Temperature Uniformity ◽  
System Parameters ◽  
Light Pipe ◽  
End Wall ◽  
Cavity Width

AbstractA Monte Carlo model is developed to simulate transient wafer heating as a function of system parameters in a kaleidoscope- or integrating light-pipe type cavity with square cross-section. Trends in wafer temperature uniformity are examined as a function of length-to-width ratio, cavity width, and the number of heating lamps. The effect on temperature determination by a radiometer placed in the bottom end wall of the cavity is simulated.

Optimization of Process Parameter and Temperature Uniformity On Wafers For Rapid Thermal Processing

1995 ◽  
Vol 387 ◽  
Author(s):  
Andreas Tillmann
Keyword(s):  
Standard Deviation ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Oxide Thickness ◽  
Simulation Software ◽  
Process Parameter ◽  
Parameter Distribution ◽  
Temperature Uniformity ◽  
New Strategy ◽  
The Impact

AbstractA new strategy based algorithm to optimize process parameter uniformity (e.g.sheet resistance, oxide thickness) and temperature uniformity on wafers in a commercially available Rapid Thermal Processing (RTP) system with independent lamp control is described. The computational algorithm uses an effective strategy to minimize the standard deviation of the considered parameter distribution. It is based on simulation software which is able to calculate the temperature and resulting parameter distribution on the wafer for a given lamp correction table. A cyclical variation of the correction values of all lamps is done while minimizing the standard deviation of the considered process parameter. After the input of experimentally obtained wafer maps the optimization can be done within a few minutes. This technique is an effective tool for the process engineer to use to quickly optimize the homogeneity of the RTP tool for particular process requirements. The methodology will be shown on the basis of three typical RTP applications (Rapid Thermal Oxidation, Titanium Silicidation and Implant Annealing). The impact of variations of correction values for single lamps on the resulting process uniformity for different applications will be discussed.

Rapid Thermal Annealing and Oxidation of Silicon Wafers with Back-Side Films

1997 ◽  
Vol 470 ◽  
Author(s):  
A. T. Fiory
Keyword(s):  
Thermal Oxidation ◽  
Sheet Resistance ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Temperature Control ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Oxide Thickness ◽  
Back Side ◽  
Control Accuracy

ABSTRACTTemperatures for lamp-heated rapid thermal processing of wafers with various back-side films were controlled by a Lucent Technologies pyrometer which uses a/c lamp ripple to compensate for emissivity. Process temperatures for anneals of arsenic and boron implants were inferred from post-anneal sheet resistance, and for rapid thermal oxidation, from oxide thickness. Results imply temperature control accuracy of 12°C to 17°C at 3 standard deviations.

Polysilicon Emitter Transistors Manufactured using a Novel Limited Reaction Processing System

1989 ◽  
Vol 146 ◽  
Author(s):  
Fred Ruddell ◽  
Colin Parkes ◽  
B Mervyn Armstrong ◽  
Harold S Gamble
Keyword(s):  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Processing System ◽  
Bipolar Transistors ◽  
Native Oxide ◽  
Plasma Oxidation ◽  
Oxide Removal ◽  
Polysilicon Emitter ◽  
Reaction Processing

ABSTRACTThis paper describes a LPCVD reactor which was developed for multiple sequential in-situ processing. The system is capable of rapid thermal processing in the presence of plasma stimulation and has been used for native oxide removal, plasma oxidation and silicon deposition. Polysilicon layers produced by the system are incorporated into N-P-N polysilicon emitter bipolar transistors. These devices fabricated using a sequential in-situ plasma clean-polysilicon deposition schedule exhibited uniform gains limited to that of long single crystal emitters. Devices with either plasma grown or native oxide layers below the polysilicon exhibited much higher gains. The suitability of the system for sequential and limited reaction processing has been established.

Rapid thermal processing chamber for in-situ x-ray diffraction

2015 ◽  
Vol 86 (1) ◽  
pp. 013902 ◽  
Author(s):  
Md. Imteyaz Ahmad ◽  
Douglas G. Van Campen ◽  
Jeremy D. Fields ◽  
Jiafan Yu ◽  
Vanessa L. Pool ◽  
...  
Keyword(s):  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
X Ray Diffraction ◽  
X Ray
Sign in / Sign up

Export Citation Format

Share Document