Formation and Properties of Porous Si Superlattices

1994 ◽  
Vol 358 ◽  
Author(s):  
M.G. Berger ◽  
R. Arens-Fischer ◽  
St. Frohnhoff ◽  
C. Dieker ◽  
K. Winz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Doping Level ◽  
Layer Structure ◽  
Optical Data ◽  
Type I ◽  
Optical Components ◽  
Porous Layers ◽  
Long Term Stability ◽  
Transmission Electron

ABSTRACTPorous silicon superlattices (PS-SL) were investigated by transmission electron microscopy (TEM), scanning electron microscopy (SEM), spectroscopic ellipsometry and reflectance spectroscopy. Type I superlattices were formed by periodically changing the current density during the etch process. The quality of the interface between layers of different porosity depends on the quality of the silicon substrate. Optical components such as Bragg reflectors or Fabry-Perot filters were designed using the optical data of single porous layers. A good long term stability of the layers is achieved by using thermal oxidation steps. Type II superlattices were formed on substrates with layers of alternating doping level. The more complex layer structure of these superlattices is explained by the selectivity of the etch process on the doping level.

The annealed (0001) α-alumina surface and its influence on thin-film growth

1995 ◽  
Vol 53 ◽  
pp. 336-337
Author(s):  
Michael W. Bench ◽  
Paul G. Kotula ◽  
C. Barry Carter
Keyword(s):  
Electron Microscopy ◽  
Surface Energy ◽  
Film Growth ◽  
Thin Film Growth ◽  
Energy Calculations ◽  
Transmission Electron ◽  
Reflection Electron Microscopy ◽  
Low Energy Electron ◽  
Surface Nature

The growth of semiconductors, superconductors, metals, and other insulators has been investigated using alumina substrates in a variety of orientations. The surface state of the alumina (for example surface reconstruction and step nature) can be expected to affect the growth nature and quality of the epilayers. As such, the surface nature has been studied using a number of techniques including low energy electron diffraction (LEED), reflection electron microscopy (REM), transmission electron microscopy (TEM), molecular dynamics computer simulations, and also by theoretical surface energy calculations. In the (0001) orientation, the bulk alumina lattice can be thought of as a layered structure with A1-A1-O stacking. This gives three possible terminations of the bulk alumina lattice, with theoretical surface energy calculations suggesting that termination should occur between the Al layers. Thus, the lattice often has been described as being made up of layers of (Al-O-Al) unit stacking sequences. There is a 180° rotation in the surface symmetry of successive layers and a total of six layers are required to form the alumina unit cell.

Methods to Monitor and Improve the Performance of Specimen Holders for Transmission Electron Cryomicroscopy

1996 ◽  
Vol 54 ◽  
pp. 454-455
Author(s):  
B. L. Armbruster ◽  
B. Kraus ◽  
M. Pan
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Electron Beam Irradiation ◽  
Beam Irradiation ◽  
Quality Of Data ◽  
Electron Cryomicroscopy ◽  
Thermal Equilibration ◽  
Transmission Electron ◽  
Electron Microscopes

One goal in electron microscopy of biological specimens is to improve the quality of data to equal the resolution capabilities of modem transmission electron microscopes. Radiation damage and beam- induced movement caused by charging of the sample, low image contrast at high resolution, and sensitivity to external vibration and drift in side entry specimen holders limit the effective resolution one can achieve. Several methods have been developed to address these limitations: cryomethods are widely employed to preserve and stabilize specimens against some of the adverse effects of the vacuum and electron beam irradiation, spot-scan imaging reduces charging and associated beam-induced movement, and energy-filtered imaging removes the “fog” caused by inelastic scattering of electrons which is particularly pronounced in thick specimens.Although most cryoholders can easily achieve a 3.4Å resolution specification, information perpendicular to the goniometer axis may be degraded due to vibration. Absolute drift after mechanical and thermal equilibration as well as drift after movement of a holder may cause loss of resolution in any direction.

scholarly journals Epitaxial Growth of Ordered In-Plane Si and Ge Nanowires on Si (001)

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 788
Author(s):  
Jian-Huan Wang ◽  
Ting Wang ◽  
Jian-Jun Zhang
Keyword(s):  
Electron Microscopy ◽  
Epitaxial Growth ◽  
Molecular Beam ◽  
Core Shell ◽  
High Quality ◽  
Quantum Devices ◽  
Wafer Scale ◽  
Transmission Electron ◽  
Controllable Growth

Controllable growth of wafer-scale in-plane nanowires (NWs) is a prerequisite for achieving addressable and scalable NW-based quantum devices. Here, by introducing molecular beam epitaxy on patterned Si structures, we demonstrate the wafer-scale epitaxial growth of site-controlled in-plane Si, SiGe, and Ge/Si core/shell NW arrays on Si (001) substrate. The epitaxially grown Si, SiGe, and Ge/Si core/shell NW are highly homogeneous with well-defined facets. Suspended Si NWs with four {111} facets and a side width of about 25 nm are observed. Characterizations including high resolution transmission electron microscopy (HRTEM) confirm the high quality of these epitaxial NWs.

CHARACTERIZATION AND ELECTRICAL PROPERTIES OF ALIGNED CARBON NANOTUBES WITH HIGH ASPECT RATIO

2011 ◽  
Vol 10 (01n02) ◽  
pp. 23-28
Author(s):  
RAVI BHATIA ◽  
V. PRASAD ◽  
M. REGHU
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Aspect Ratio ◽  
Multiwall Carbon Nanotubes ◽  
High Quality ◽  
Transmission Electron Microscopy Analysis ◽  
Transmission Electron ◽  
Electron Microscopy Analysis ◽  
High Degree

High-quality multiwall carbon nanotubes (MWNTs) were produced by a simple one-step technique. The production of MWNTs was based on thermal decomposition of the mixture of a liquid phase organic compound and ferrocene. High degree of alignment was noticed by scanning electron microscopy. The aspect ratio of as-synthesized MWNTs was quite high (more than 4500). Transmission electron microscopy analysis showed the presence of the catalytic iron nanorods at various lengths of MWNTs. Raman spectroscopy was used to know the quality of MWNTs. The ratio of intensity of the G-peak to the D-peak was very high which revealed high quality of MWNTs. Magnetotransport studies were carried out at low temperature and a negative MR was noticed.

scholarly journals Solvothermal Synthesis of Mn3O4Nanoparticle/Graphene Sheet Composites and Their Supercapacitive Properties

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Y. F. Liu ◽  
G. H. Yuan ◽  
Z. H. Jiang ◽  
Z. P. Yao
Keyword(s):  
Electron Microscopy ◽  
Graphene Sheet ◽  
Low Cost ◽  
High Specific Capacitance ◽  
Ethanol Solution ◽  
Diffraction Field ◽  
Electrochemical Performances ◽  
One Pot ◽  
Long Term Stability ◽  
Transmission Electron

Mn3O4nanoparticle/graphene sheet (GM) composites were synthesized via a one-pot and low-cost solvothermal process in an ethanol solution. The as-prepared materials were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Results showed that the nanosized Mn3O4particles had tetragonal hausmannite structure and were successfully loaded on the graphene sheets. Moreover, the electrochemical performances of GM composites produced by different mass percents of Mn2+/graphite oxide (GO) were evaluated by means of cyclic voltammetry and galvanostatic charge-discharge studies. The composite prepared with Mn2+/GO mass percent of 10 : 90 showed a high specific capacitance of 245 F/g at 5 mV/s in the 6 M KOH solution and better long-term stability along with 81% of its initial capacitance after 1200 cycles at 0.5 A/g.

Application and Study of Reactive Polyacrylate Microgel in Pigment Paint of Printed Fabric

2011 ◽  
Vol 311-313 ◽  
pp. 1044-1048
Author(s):  
Hong Long Xing ◽  
Shui Lin Chen
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Sodium Dodecyl ◽  
Ammonium Persulfate ◽  
Color Fastness ◽  
Adhesive Film ◽  
Transmission Electron ◽  
Divinyl Benzene

Polyacrylate microgel emulsion was prepared by emulsion polymerization using styrene, α-n-butyl acrylate and methyl methacrylate as monomer, polyoxyethylene octylphenol ether (TX-30) and sodium dodecyl sulfate(SDS) as combine emulsifier, divinyl benzene and ammonium persulfate (APS) as initiator，respectively. The prepared microgel was analyzed by a variety of measurment methods, such as Fourier transform infrared spectroscopy and transmission electron microscopy. The effect of microgel on the rheological properties of adhesives, leveling, mechanical properties and pigment printing performance was studied. The rhelogy and the color fastness of the pigment printing binder of printed fabrics were measured by rheometer and friction color fastness test instruments, respectively. At the same time, the mechanical properties of the adhesive film was measured by strength tester. The results show that the thixotropy, leveling and mechanical properties of adhesive printing binder and pringting quality of coating fabrics were improved when the microgel was added.

Cleaning Treatment to Advance the Quality of FIB Samples for Transmission Electron Microscopy

2004 ◽  
Vol 10 (S02) ◽  
pp. 1166-1167
Author(s):  
Wolfgang Gruenewald ◽  
Hans-Juergen Engelmann ◽  
Beate Volkmann
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Transmission Electron ◽  
Cleaning Treatment

Extended abstract of a paper presented at Microscopy and Microanalysis 2004 in Savannah, Georgia, USA, August 1–5, 2004.

Structure of InAs Quantum Dots in Si Matrix Investigated by High Resolution Electron Microscopy

1999 ◽  
Vol 571 ◽  
Author(s):  
N. D. Zakharov ◽  
P. Werner ◽  
V. M. Ustinov ◽  
A.R. Kovsh ◽  
G. E. Cirlin ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Critical Thickness ◽  
High Resolution Electron Microscopy ◽  
Geometrical Parameters ◽  
Inas Quantum Dots ◽  
Temperature Growth ◽  
Transmission Electron ◽  
Resolution Electron

ABSTRACTQuantum dot structures containing 2 and 7 layers of small coherent InAs clusters embedded into a Si single crystal matrix were grown by MBE. The structure of these clusters was investigated by high resolution transmission electron microscopy. The crystallographic quality of the structure severely depends on the substrate temperature, growth sequence, and the geometrical parameters of the sample. The investigation demonstrates that Si can incorporate a limited volume of InAs in a form of small coherent clusters about 3 nm in diameter. If the deposited InAs layer exceeds a critical thickness, large dislocated InAs precipitates are formed during Si overgrowth accumulating the excess of InAs.

Collagen Expression in Tissue Engineered Cartilage of Aged Human Articular Chondrocytes in a Rotating Bioreactor

2003 ◽  
Vol 26 (4) ◽  
pp. 319-330 ◽  
Author(s):  
S. Marlovits ◽  
B. Tichy ◽  
M. Truppe ◽  
D. Gruber ◽  
W. Schlegel
Keyword(s):  
Electron Microscopy ◽  
Collagen Type ◽  
Articular Chondrocytes ◽  
Three Dimensional ◽  
Collagen Type I ◽  
Human Articular Chondrocytes ◽  
Type I ◽  
Transmission Electron ◽  
Low Shear Stress ◽  
Engineered Cartilage

This study describes the culture and three-dimensional assembly of aged human articular chondrocytes under controlled oxygenation and low shear stress in a rotating-wall vessel. Chondrocytes cultured in monolayer were released and placed without any scaffold as a single cell suspension in a rotating bioreactor for 12 weeks. Samples were analyzed with immunohistochemistry, molecular biology and electron microscopy. During serial monolayer cultures chondrocytes dedifferentiated to a “fibroblast-like” structure and produced predominantly collagen type I. When these dedifferentiated cells were transferred to the rotating bioreactor, the cells showed a spontaneous aggregation and formation of solid tissue during the culture time. Expression of collagen type II and other components critical for the extracellular cartilage matrix could be detected. Transmission electron microscopy revealed a fine network of randomly distributed collagen fibrils. This rotating bioreactor proves to be a useful tool for providing an environment that enables dedifferentiated chondrocytes to redifferentiate and produce a cartilage-specific extracellular matrix.

A method of precise misorientation determination

2003 ◽  
Vol 36 (6) ◽  
pp. 1319-1323 ◽  
Author(s):  
A. Morawiec
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Spatial Resolution ◽  
Standard Procedure ◽  
Good Spatial Resolution ◽  
Transmission Electron ◽  
Order Of Magnitude ◽  
Achievable Accuracy ◽  
Better Than

A method that improves the accuracy of misorientations determined from Kikuchi patterns is described. It is based on the fact that some parameters of a misorientation calculated from two orientations are more accurate than other parameters. A procedure which eliminates inaccurate elements is devised. It requires at least two foil inclinations. The quality of the approach relies on the possibility to set large sample-to-detector distances and the availability of good spatial resolution of transmission electron microscopy. Achievable accuracy is one order of magnitude better than the accuracy of the standard procedure.

Sign in / Sign up

Export Citation Format

Share Document