Observation of Patterns by Magnetic Force Microcopy in Fe-alloys with Shape Memory Effect

2001 ◽  
Vol 674 ◽  
Author(s):  
M. I.N. da Silva ◽  
J. C. González ◽  
M. S. Andrade
Keyword(s):  
Magnetic Properties ◽  
Magnetic Moment ◽  
Magnetic Force ◽  
Stainless Steel Sample ◽  
X Ray Diffraction ◽  
Magnetic Microstructure ◽  
X Ray ◽  
Probe Surface ◽  
Surface Separation ◽  
Average Maximum

ABSTRACTIn this study, we investigated the magnetic domains of a FeMnSiNiCr stainless steel sample using Magnetic Force Microscope (MFM). We compared the magnetic patterns obtained by scanning the sample with three coated probes with different magnetic properties: Medium magnetic moment (MM), low magnetic moment (LM), and low coercivity (LC). The probe-surface separation was varied between 25 to 300 nm in order to quantify the magnetic microstructure of the sample. A simple model for the probe-sample interaction was used to interpret the contrast change as a function of the probe-surface separation. The experiment showed that the average maximum frequency decreases with the probe-surface separation and the intensity of the frequency is the strongest for the MM probe. X ray diffraction experiments were used to identify the different phases present in the sample. The X-ray diffraction experiments together with the MFM showed that α-phase islands surrounded by a γ-phase matrix are responsible for the magnetic properties of the sample.

Magnetic Force Microscopic Description of the Structure of Glow Discharge Nitrided Layers Produced on Ni27Ti2AlMoNb Steel

2011 ◽  
Vol 172-174 ◽  
pp. 851-856
Author(s):  
Tomasz Borowski ◽  
Jerzy Jeleńkowski ◽  
Tadeusz Wierzchoń
Keyword(s):  
Magnetic Properties ◽  
Glow Discharge ◽  
Magnetic Force ◽  
S Phase ◽  
Magnetic Force Microscope ◽  
Structural Components ◽  
X Ray Diffraction ◽  
Microscopic Description ◽  
X Ray ◽  
Lattice Constants

The paper analyzes the magnetic properties and stability of austenite, athermal martensite, and deformation martensite that form in Ni27Ti2AlMoNb steel subjected to glow discharge assisted nitriding, and also of nitrogen austenite (S phase with various lattice constants) which occurs when the nitriding process is conducted below the temperature As. The analysis of these structural components and their morphology was performed using a magnetic force microscope (MFM), whereas the phase composition of the nitrided layers produced on this steel was determined by X-ray diffraction.

Preparation and Magnetic Properties of Nanocrystalline (Fe,Cr)-N

2012 ◽  
Vol 625 ◽  
pp. 222-225
Author(s):  
Wen Jiang Feng ◽  
Chuan Yin Wang ◽  
Hao Hua Zhang
Keyword(s):  
Crystal Structure ◽  
Solid Solution ◽  
Magnetic Properties ◽  
Magnetic Moment ◽  
Single Phase ◽  
Nitrogen Atmosphere ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Crystalline ◽  
Intrinsic Magnetic Moment

The nano-crystalline (Fe,Cr)N was prepared as a single phase by milling Fe80Cr20 in a nitrogen atmosphere. Its crystal structure is determined to be the cubic rock salt-type CrN by X-ray diffraction measurements. The nano-crystalline is stable up to above 773 K and decomposes into (Fe,Cr)N and Fe-Cr solid solution. Due to the combination of Fe atoms and N ones, the intrinsic magnetic moment of Fe atoms is reduced, which is confirmed by our measurements.

scholarly journals SYNTHESIS AND MAGNETIC PROPERTIES OF BINUCLEAR COMPLEX [N(n-C4H9)4][MnIIFeIII(ox)3]

2012 ◽  
Vol 12 (1) ◽  
pp. 89-93
Author(s):  
Fahimah Martak ◽  
Hamzah Fansuri ◽  
Sekarayu Dianing Putri
Keyword(s):  
Magnetic Properties ◽  
Magnetic Moment ◽  
Binuclear Complex ◽  
Organic Cation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tetrabutyl Ammonium ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Binuclear complex, [N(n-C4H9)4][MnIIFeIII(ox)3] (ox=oxalate), has been synthesized and characterized. Binuclear complex with formula of [N(n-C4H9)4][MnIIFeIII(ox)3] was synthesized by forming precursor K3[Fe(ox)3] which was followed by adding manganese chloride and tetrabutyl ammonium chloride. Characterization of the complex was made by microanalysis, FT-IR spectroscopy, x-ray diffraction and Magnetic Susceptibility Balance. Magnetic moment of binuclear complex [N(n-C4H9)4][MnIIFeIII(ox)3] is 7.81 BM. The compound has higher magnetic moment than the previously reported compound with different organic cation, [N(n-C5H11)4][MnIIFeIII(ox)3]. This behavior might be associated with the decreasing range among layers on polymeric network.

Effect of Chemical Reaction Temperature on Magnetic Properties of Cu2+ Substituted NiZn Ferrites

2013 ◽  
Vol 547 ◽  
pp. 181-193 ◽  
Author(s):  
Neelam S. Shinde ◽  
Sujata. S. Khot ◽  
R.M. More ◽  
Shrikant C. Watawe
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Structural Analysis ◽  
Reaction Temperature ◽  
Magnetic Moment ◽  
Magnetic Losses ◽  
X Ray Diffraction ◽  
Precursor Method ◽  
Oxalate Precursor ◽  
X Ray

Ni-Cu-Zn ferrites with general formula Ni0.5Cux/2Zn0.5-x/2Fe2O4 (with x = 0.3, 0.4, 0.5 and 0.6) have been synthesized using oxalate precursor method with different precursor reaction temperatures in the range 100C to 700C. The structural analysis has been carried out using X-ray diffraction studies which reveal the formation of ferrites structure. The lattice parameters obtained using the most intense 311 peak are found to be in the range 8.37 to 8.42 Å for all the samples. The saturation magnetization is found to be in the range 20 to 51 emu/g, while the magnetic moment is found to be in the range 0.63 to 1.5 µB. The magnetic losses were found to be maximum for the samples obtained at precursor reaction temperature of 350C. The grain size is found to be in the range 0.4 to 2.0 µm. There is variation in the magnetic properties for different precursor temperatures indicating the effect of reaction history on the various parameters studied.

scholarly journals Green synthesis and characterization of hexaferrite strontium-perovskite strontium photocatalyst nanocomposites

2020 ◽  
Vol 43 (1) ◽  
pp. 26-42 ◽  
Author(s):  
Zahra Hajian Karahroudi ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Magnetic Properties ◽  
Green Synthesis ◽  
Sol Gel ◽  
Synthesis Method ◽  
Combustion Method ◽  
Lemon Juice ◽  
X Ray Diffraction ◽  
X Ray ◽  
Auto Combustion

AbstractThis study presents a preparation of SrFe12O19– SrTiO3 nanocomposite synthesis via the green auto-combustion method. At first, SrFe12O19 nanoparticles were synthesized as a core and then, SrTiO3 nanoparticles were prepared as a shell for it to manufacture SrFe12O19–SrTiO3 nanocomposite. A novel sol-gel auto-combustion green synthesis method has been used with lemon juice as a capping agent. The prepared SrFe12O19–SrTiO3 nanocomposites were characterized by using several techniques to characterize their structural, morphological and magnetic properties. The crystal structures of the nanocomposite were investigated via X-ray diffraction (XRD). The morphology of SrFe12O19– SrTiO3 nanocomposite was studied by using a scanning electron microscope (SEM). The elemental composition of the materials was analyzed by an energy-dispersive X-ray (EDX). Magnetic properties and hysteresis loop of nanopowder were characterized via vibrating sample magnetometer (VSM) in the room temperature. Fourier transform infrared spectroscopy (FTIR) spectra of the samples showed the molecular bands of nanoparticles. Also, the photocatalytic behavior of nanocomposites has been checked by the degradation of azo dyes under irradiation of ultraviolet light.

scholarly journals Influence of Li2CO3 addition on electrical and magnetic properties of Ni0.6Mg0.4Fe2O4

2020 ◽  
Vol 10 (03) ◽  
pp. 2050003
Author(s):  
M. R. Hassan ◽  
M. T. Islam ◽  
M. N. I. Khan
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Low Frequency ◽  
Solid State Reaction Method ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Frequency Regime ◽  
Xrd Patterns

In this research, influence of adding Li2CO3 (at 0%, 2%, 4%, 6%) on electrical and magnetic properties of [Formula: see text][Formula: see text]Fe2O4 (with 60% Ni and 40% Mg) ferrite has been studied. The samples are prepared by solid state reaction method and sintered at 1300∘C for 6[Formula: see text]h. X-ray diffraction (XRD) patterns show the samples belong to single-phase cubic structure without any impurity phase. The magnetic properties (saturation magnetization and coercivity) of the samples have been investigated by VSM and found that the higher concentration of Li2CO3 reduces the hysteresis loss. DC resistivity increases with Li2CO3 contents whereas it decreases initially and then becomes constant at lower value with temperature which indicates that the studied samples are semiconductor. The dielectric dispersion occurs at a low-frequency regime and the loss peaks are formed in a higher frequency regime, which are due to the presence of resonance between applied frequency and hopping frequency of charge carriers. Notably, the loss peaks are shifted to the lower frequency with Li2CO3 additions.

Ternary Antimonides RE4T7Sb6 (RE=Gd–Lu; T =Ru, Rh) with Cubic U4Re7Si6-type Structure

2013 ◽  
Vol 68 (9) ◽  
pp. 971-978 ◽  
Author(s):  
Inga Schellenberg ◽  
Ute Ch. Rodewald ◽  
Christian Schwickert ◽  
Matthias Eul ◽  
Rainer Pöttgen
Keyword(s):  
Magnetic Susceptibility ◽  
Single Crystal ◽  
Magnetic Moment ◽  
Induction Furnace ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
X Ray ◽  
Antiferromagnetic Ordering ◽  
Arc Melting ◽  
Intermediate Valent

The ternary antimonides RE4T7Sb6 (RE=Gd-Lu; T =Ru, Rh) have been synthesized from the elements by arc-melting and subsequent annealing in an induction furnace. The samples have been characterized by powder X-ray diffraction. Four structures were refined on the basis of single-crystal X-ray diffractometer data: U4Re7Si6 type, space group Im3m with a=862.9(2) pm, wR2=0.0296, 163 F2 values for Er4Ru7Sb6; a=864.1(1) pm, wR2=0.1423, 153 F2 values for Yb4Ru7Sb6; a=872.0(2) pm, wR2=0.0427, 172 F2 values for Tb4Rh7Sb6; and a=868.0(2) pm, wR2=0.0529, 154 F2 values for Er4Rh7Sb6, with 10 variables per refinement. The structures have T1@Sb6 octahedra and slightly distorted RE@T26Sb6 cuboctahedra as building units. The distorted cuboctahedra are condensed via all trapezoidal faces, and this network leaves octahedral voids for the T1 atoms. The ruthenium-based series of compounds was studied by temperature-dependent magnetic susceptibility measurements. Lu4Ru7Sb6 is Pauli-paramagnetic. The antimonides RE4Ru7Sb6 with RE=Dy, Ho, Er, and Tm show Curie-Weiss paramagnetism. Antiferromagnetic ordering occurs at 10.0(5), 5.1(5) and 4.0(5) K for Dy4Ru7Sb6, Ho4Ru7Sb6 and Er4Ru7Sb6, respectively, while Tm4Ru7Sb6 remains paramagnetic. Yb4Ru7Sb6 is an intermediate-valent compound with a reduced magnetic moment of 3.71(1) μB per Yb as compared to 4.54 μB for a free Yb3+ ion

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Magnetic Properties of Bulk Zn0.95-XMnXFe0.05O2 Prepared by Sol-Gel Method and Subsequent Hot Pressing

2011 ◽  
Vol 268-270 ◽  
pp. 356-359 ◽  
Author(s):  
Wen Song Lin ◽  
C. H. Wen ◽  
Liang He
Keyword(s):  
Magnetic Properties ◽  
Photoelectron Spectroscopy ◽  
Raw Materials ◽  
Sol Gel ◽  
Secondary Phase ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Doped Zno

Mn, Fe doped ZnO powders (Zn0.95-xMnxFe0.05O2, x≤0.05) were synthesized by an ameliorated sol-gel method, using Zn(CH3COO)2, Mn(CH3COO)2and FeCl2as the raw materials, with the addition of vitamin C as a kind of chemical reducer. The resulting powder was subsequently compacted under pressure of 10 MPa at the temperature of 873K in vacuum. The crystal structure and magnetic properties of Zn0.95-xMnxFe0.05O2powder and bulk samples have been investigated by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). X-ray photoelectron spectroscopy (XPS) was used to study chemical valence of manganese, iron and zinc in the samples. The x-ray diffraction (XRD) results showed that Zn0.95-xMnxFe0.05O (x≤0.05) samples were single phase with the ZnO-like wurtzite structure. No secondary phase was found in the XRD spectrum. X-ray photoelectron spectroscopy (XPS) showed that Fe and Mn existed in Zn0.95-xMnxFe0.05O2samples in Fe2+and Mn2+states. The results of VSM experiment proved the room temperature ferromagnetic properties (RTFP) of Mn, Fe co-doped ZnO samples.

Sign in / Sign up

Export Citation Format

Share Document