scholarly journals Potential use of PET and PP as partial replacement of sand in structural concrete

2021 ◽  
Vol 26 (3) ◽  
Author(s):  
Priscila Marques Correa ◽  
Diego Guimarães ◽  
Ruth Marlene Campomanes Santana ◽  
Ângela Gaio Graeff
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Elasticity Modulus ◽  
Chloride Ion ◽  
Morphological Properties ◽  
Partial Replacement ◽  
Chloride Ion Penetration ◽  
Mechanical Durability ◽  
Dsc Curves ◽  
Potential Use

ABSTRACT The use of polymeric residues in the civil construction has been the target of many studies aiming to reduce the volume of post-consumer plastics in the environment. This work focuses on the viability to use polyethylene terephthalate (PET) and polypropylene (PP) as partial replacement to sand in concrete. PET and PP flakes from post-consumer packings were used as light aggregate to partially replace, individually, 10% in volume of sand. The effect of adding these polymers was investigated in terms of physical, mechanical, durability and morphological properties of the concrete. Physical properties were measured in terms of water absorption, voids content and specific mass. Mechanical properties were measured in terms of compressive strength and elasticity modulus. Durability properties were measured in terms of capillarity water absorption and electrical indication of the concrete to resist to chloride ion penetration. MEV and EDS were used to carry out morphological analysis. DSC curves were carried out to evaluate thermal properties of the polymeric flakes. Contact anlge test was also performed. The partial addition of PET and PP polymers reduced the compressive strength by 20%, whilst the reduction of the elasticity modulus was 16% for PET samples, and almost insignificant for PP samples. The durability results show that the polymers contributed to increase the resistance of the samples to chloride penetration by 15% and 57%, for PET and PP samples, respectively; however, there was an increase in the voids content and water absorption. In the morphological test it is possible to observe a lower interfacial adhesion between PP and the cementions paste in comparison to PET.

Experimental Study on Sustainable Concrete with the Mixture of Low Calcium Fly Ash and Lime as a Partial Replacement of Cement

2011 ◽  
Vol 250-253 ◽  
pp. 307-312 ◽  
Author(s):  
Muthuramalingam Jayakumar ◽  
M. Salman Abdullahi
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Chloride Ion ◽  
Apparent Volume ◽  
Partial Replacement ◽  
Fly Ash Concrete ◽  
Low Calcium ◽  
Chloride Ion Penetration ◽  
Ion Penetration

Even though the use of fly ash in concrete is nowadays a common practice, its relatively slow pozzolanic reactivity hinders its greater utilization; hence efficient methods of activation are on demand. This study was carried out to evaluate the influence of lime as a chemical activator on the mechanical and durability properties of high strength fly ash concrete. Mixtures were made with 0, 30, 40, and 50% of cement replaced by low calcium fly ash. Corresponding mixtures were also made with the same amount of fly ash and addition of 10% of lime to each mixture. For each concrete mixture, slump, compressive strength, water absorption, sorptivity, apparent volume of permeable voids, and resistance to chloride-ion penetration were measured. The results obtained showed that addition of lime improved the compressive strength significantly at all ages. The strength of all the fly ash mixtures containing lime surpassed that of the corresponding Portland cement mix at 60 days. Addition of lime also improved the sorptivity and resistance to chloride-ion penetration of the fly ash concrete. It however increases the water absorption and the volume of permeable voids of the fly ash concrete.

scholarly journals Copper Slag of Pyroxene Composition as a Partial Replacement of Natural Aggregate for Concrete Production

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 439
Author(s):  
Sandra Filipović ◽  
Olivera Đokić ◽  
Aleksandar Radević ◽  
Dimitrije Zakić
Keyword(s):  
Chloride Ion ◽  
Copper Slag ◽  
Partial Replacement ◽  
Copper Ore ◽  
Silicon Iron ◽  
Low Resistance ◽  
Natural Aggregate ◽  
Chloride Ion Penetration ◽  
Concrete Production ◽  
Technical Properties

Copper slag, a by-product of the pyrometallurgical process used for obtaining copper from copper ore in Bor, Serbia, contains mainly silicon, iron, calcium, and aluminium oxides. Due to such properties, it is disposed of in landfills. Despite the favourable technical properties copper slag aggregates possess, such as low-water absorption (WA24 0.6%), low resistance to fragmentation (LA 10%), and low resistance to wear (MDE 4%), its use in the construction industry is still limited. The results of testing the technical properties of copper slag aggregates (CSAs) as a potential replacement for natural river aggregate (RA) are presented in this paper. The experiments included tests on three concrete mixtures with partial replacement of coarse natural aggregate with copper slag. The replacement of RA particle sizes of 8/16 mm and 16/31.5 mm with CSA in the amount of 20% + 50% and 50% + 50% resulted in an increase in the compressive strength of 12.4% and 10.5%, respectively. The increase of CSA content led to a decrease in water penetration resistance and salt-frost resistance of concrete, whereas the resistance to chloride ion penetration did not change significantly.

scholarly journals Partial Replacement of Cement with Waste Paper Sludge Ash

2021 ◽  
Vol 9 (11) ◽  
pp. 1975-1983
Author(s):  
Shahid Bashir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Cement Industry ◽  
Waste Paper ◽  
Partial Replacement ◽  
Dry Density ◽  
Paper Sludge ◽  
Paper Sludge Ash ◽  
Sludge Ash

Abstract: Cement production is one of the sources that emit carbon dioxide, in addition to deforestation and combustion of fossil fuels also leads to ill effects on environment. The global cement industry accounts for 7% of earth’s greenhouse gas emission. To enhance the environmental effects associated with cement manufacturing and to constantly deplore natural resources, we need to develop other binders to make the concrete industry sustainable. This work offers the option to use waste paper sludge ash as a partial replacement of cement for new concrete. In this study cement in partially replaced as 5%, 10%, 15% and 20% by waste paper sludge ash in concrete for M25 mix and tested for compressive strength, tensile strength, water absorption and dry density up to the age of 28days and compared it with conventional concrete, based on the results obtained, it is found that waste paper ash may be used as a cement replacement up to 5% by weight and the particle size is less the 90µm to prevent reduction in workability. Keywords: slump test, Compressive strength, split tensile strength, water absorption test, Waste Paper Sludge Ash Concrete, Workability.

scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

scholarly journals Use of Recycled Tyre Rubber in Non-structural Concrete

2018 ◽  
Vol 203 ◽  
pp. 06001
Author(s):  
Muhammad Bilal Waris ◽  
Hussain Najwani ◽  
Khalifa Al-Jabri ◽  
Abdullah Al-Saidy
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Structural Concrete ◽  
Cement Ratio ◽  
Mix Proportion ◽  
Water To Cement Ratio ◽  
Concrete Blocks

To manage tyre waste and conserve natural aggregate resource, this research investigates the use of waste tyre rubber as partial replacement of fine aggregates in non-structural concrete. The research used Taguchi method to study the influence of mix proportion, water-to-cement ratio and tyre rubber replacement percentage on concrete. Nine mixes were prepared with mix proportion of 1:2:4, 1:5:4 and 1:2.5:3; water-to-cement ratio of 0.25, 0.35 and 0.40 and rubber to fine aggregate replacement of 20%, 30% and 40%. Compressive strength and water absorption tests were carried out on 100 mm cubes. Compressive strength was directly proportional to the amount of coarse aggregate in the mix. Water-to-cement ratio increased the strength within the range used in the study. Strength was found to be more sensitive to the overall rubber content than the replacement ratio. Seven out of the nine mixes satisfied the minimum strength requirement for concrete blocks set by ASTM. Water absorption and density for all mixes satisfied the limits applicable for concrete blocks. The study indicates that mix proportions with fine to coarse aggregate ratio of less than 1.0 and w/c ratio around 0.40 can be used with tyre rubber replacements of up to 30 % to satisfy requirements for non-structural concrete.

Study of Coconut Charcoal Powder and Egg Shell Powder as Partial Replacement to Fine Aggregates and Cement in Load Bearing Concrete Bricks

2020 ◽  
Vol 853 ◽  
pp. 120-125
Author(s):  
Airvin John C. Palacio ◽  
Nioro G. Furiscal ◽  
Katrina Mae L. Abalos ◽  
Dioven Angelo A. Alferez ◽  
Edmer A. Bade ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Construction Materials ◽  
Control Sample ◽  
Agricultural Wastes ◽  
Partial Replacement ◽  
Agriculture Sector ◽  
Coconut Charcoal ◽  
Fine Aggregates ◽  
Egg Shell

Waste disposal is one of the issues that plague the society. Philippines is an agricultural country due to its strategic location in the tropics. Because of this nature, the agriculture sector tends to produce a huge amount of waste that if not disposed properly could pose a threat to the society and to the environment. With the advancement of technology, it has been a challenge for researchers to improve the quality of construction materials that is used in the industry. Studies have been performed on the possibilities of incorporating agricultural wastes to various construction materials as a form of waste diversion. In order to address the problem with agricultural wastes as well as to improve the property of construction materials, a study on coconut waste and eggshell waste was conducted as a constituent in concrete brick production. In this study, the density, compressive strength as well as the water absorption of concrete bricks with coconut charcoal powder (CCP) and eggshell powder (ESP) as replacement for fine aggregates and cement was conducted. Different mix ratios (0%, 2.5%, 5%, 10% CCP with a constant value of 5% ESP in each mix ratio) were carried out and the results were compared to a control sample. From the results of the density test, the concrete bricks with 5% CCP and 5% ESP was the lightest at a density of 1678.184 kg/m3, it also showed the least water absorption at 8.58% and exhibited the highest compressive strength at 17.5 MPa.

scholarly journals Durability Properties of concrete incorporating calcined Phyllite

2021 ◽  
Author(s):  
DALPAT CHUNDAWAT ◽  
DINESH SHARMA ◽  
Sandeep Tomar
Keyword(s):  
Ball Mill ◽  
Laboratory Tests ◽  
Metamorphic Rock ◽  
Underground Mining ◽  
Chloride Ion ◽  
Partial Replacement ◽  
Basic Medium ◽  
Chloride Ion Penetration ◽  
Strength And Durability ◽  
Maximum Content

The environmental and economic concern is the biggest challenge that concrete industry is facing today. Advancement in utilization of wastes in concrete as a mixture reduces usage of natural resources. Phyllite is a kind of foliated metamorphic rock generates during underground mining .Phyllite was calcined at 850 to 900oC in furnace and ground in ball mill. In this study, cement was partially replaced by weight with calcined phyllite to make M30 grade of concrete with 0% (Control mix), 2%, 4%, 6%, 8%, & 10%, (which are designated as M1, M2, M3, M4, M5 and M6). The laboratory tests such as slump value, compressive strength, flexural strength, water absorption, chloride ion penetration and durability in acidic and basic medium were conducted on the phyllite concrete and results are compared with the control mix. Through results it is concluded that cement can be replaced in concrete at the tune of 8% with Calcine Phyllite (CP) without affecting the strength and durability. The aim of the experiment is to find the maximum content of mines calcined Phyllite that can be used as a partial replacement of cement without compromising the quality on any of the characteristics of concrete.

scholarly journals Characteristics of Eco-Friendly Metakaolin Based Geopolymer Concrete Pavement Bricks

2020 ◽  
Vol 38 (11A) ◽  
pp. 1706-1716
Author(s):  
Wasan I. Khalil ◽  
Qias J. Frayyeh ◽  
Mahmood F. Ahmed
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Abrasion Resistance ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Geopolymer Concrete ◽  
Clay Brick ◽  
Waste Plastic ◽  
Wide Range ◽  
Geopolymer Binder

The purpose of this work is to investigate the possibility to recycled and reused of waste clay brick and waste plastic as constituents in the production of green Geopolymer concrete paving bricks. Powder of clay brick waste (WBP) was used as a partial replacement of Metakaolin (MK) in Geopolymer binder. Moreover, recycled clay brick waste aggregate (BA) and plastic waste aggregate (PL) were incorporated as coarse aggregate in mixtures of Metakaolin based Geopolymer concrete (MK-GPC) pavement bricks. Six types of mixtures were prepared and cast as pavement bricks with dimensions of 150×150×100 mm. All samples have been tested for compressive strength, water absorption and abrasion resistance at age of 28 days; and compared the results with the requirements of Iraqi specification No.1606-2006. The MK-GPC pavement bricks present a compressive strength of 31-47MPa, water absorption of 3.66% to5.32% and abrasion resistance with groove length between 21.78mm to 18.91 mm. These types of pavement bricks are classified as a medium to light capacity for weight loading, and it is possible to be used in wide range of paving applications, especially in aggressive wearing environment.

scholarly journals Evaluation of Cassava Effluent as Organic Admixture in Concrete Production for Farm Structures

2020 ◽  
pp. 271-282
Author(s):  
Ovie Isaac AKPOKODJE ◽  
Goodnews Goodman AGBI ◽  
Hilary UGURU
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Fresh Water ◽  
Absorption Rate ◽  
International Standards ◽  
Partial Replacement ◽  
Strength Development ◽  
Water Absorption Rate ◽  
Concrete Production ◽  
Farm Structures

This paper evaluated the influence of cassava effluent on the compressive strength of concrete for farm structures. Three sets of concrete cubes were produced with a concrete mix ratio of 1:2:4 (C 15) and a water to cement ratio (w c-1) of 0.5. The 1st set was produced with 100% fresh water (tap water). The 2nd set was produced with 75% partial replacement of the fresh water with fresh cassava effluent, while the 3rd set was produced with 75% partial replacement of the fresh water with old cassava effluent. The density, water absorption rate and compressive strength of the concrete cubes was tested in accordance with ASTM International standards, at the end of 7, 14, 21, 28 and 56 curing days. The results revealed that, the cassava effluent slightly increased the cubes density; but reduced their water absorption rate. The study further showed that, concrete produced with fresh cassava effluent, developed the highest compressive strength (29.57 MPa) at the end of the 56th curing day. In contrast, concrete produced with old cassava effluent developed the lowest compressive strength (24.43 MPa) at day 56, which was lower than the compressive strength of 27.18 MPa developed by the concrete produced with fresh water (also at day 56). In addition, the cassava effluent retarded the initial rate of strength development, as such, increasing its prospect as an organic concrete admixture. This study will be helpful in mitigating the harmful effects of cassava effluent in the environment, since it can be utilized in concrete production.

Sign in / Sign up

Export Citation Format

Share Document