EFFECT OF JET SHAPE ON THE HEAT TRANSFER IN TRAILING EDGE MODEL

2016 ◽  
Author(s):  
Unal Uysal ◽  
Yuksel Korkmaz ◽  
MinKing K. Chyu
Keyword(s):  
Heat Transfer ◽  
Trailing Edge

Influence of tip clearance and cavity depth on heat transfer in a cutback squealer tip

2020 ◽  
pp. 095441002096469
Author(s):  
Weijie Wang ◽  
Shaopeng Lu ◽  
Hongmei Jiang ◽  
Qiusheng Deng ◽  
Jinfang Teng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
High Heat ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Cavity Depth ◽  
High Heat Transfer ◽  
Blade Tip ◽  
High Heat Transfer Coefficient

Numerical simulations are conducted to present the aerothermal performance of a turbine blade tip with cutback squealer rim. Two different tip clearance heights (0.5%, 1.0% of the blade span) and three different cavity depths (2.0%, 3.0%, and 6.0% of the blade span) are investigated. The results show that a high heat transfer coefficient (HTC) strip on the cavity floor appears near the suction side. It extends with the increase of tip clearance height and moves towards the suction side with the increase of cavity depth. The cutback region near the trailing edge has a high HTC value due to the flush of over-tip leakage flow. High HTC region shrinks to the trailing edge with the increase of cavity depth since there is more accumulated flow in the cavity for larger cavity depth. For small tip clearance cases, high HTC distribution appears on the pressure side rim. However, high HTC distribution is observed on suction side rim for large tip clearance height. This is mainly caused by the flow separation and reattachment on the squealer rims.

scholarly journals Influence of Active Cooling at the Trailing Edge on the Thermal Behavior of a Tilting-Pad Journal Bearing

Lubricants ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 26
Author(s):  
Nico Buchhorn ◽  
Michael Stottrop ◽  
Beate Bender
Keyword(s):  
Heat Transfer ◽  
Thermal Behavior ◽  
Experimental Results ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Active Cooling ◽  
Oil Supply ◽  
Tilting Pad ◽  
Carry Over ◽  
Lower Temperature

In tilting-pad journal bearings (TPJB) with a non-flooded lubrication concept, higher maximum pad temperatures occur than with a flooded bearing design due to the lower convective heat transfer at the pad edges. In this paper, we present an approach to influence the thermal behavior of a five-pad TPJB by active cooling. The aim of this research is to investigate the influence of additional oil supply grooves at the trailing edge of the two loaded pads on the maximum pad temperature of a large TPJB in non-flooded design. We carry out experimental and numerical investigations for a redesigned test bearing. Within the experimental analysis, the reduction in pad temperature is quantified. A simulation model of the bearing is synthesized with respect to the additional oil supply grooves. The simulation results are compared with the experimental data to derive heat transfer coefficients for the pad surfaces. The experimental results indicate a considerable reduction of the maximum pad temperatures. An overall lower temperature level is observed for the rear pad in circumferential direction (pad 4). The authors attribute this effect by a cooling oil carry-over from the previous pad (3). Within the model limits, a good agreement of the simulation and experimental results can be found.

Heat Transfer and Pressure Drop in a Converging Pedestal Array With Exit Area Variation

2018 ◽  
Author(s):  
L. W. Soma ◽  
F. E. Ames ◽  
S. Acharya
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Flow Path ◽  
Internal Cooling ◽  
Channel Measurements ◽  
Trailing Edge ◽  
Cooling Air

The trailing edge of a vane is one of the most difficult areas to cool due to a narrowing flow path, high external heat transfer rates, and deteriorating external film cooling protection. Converging pedestal arrays are often used as a means to provide internal cooling in this region. The thermally induced stresses in the trailing edge region of these converging arrays have been known to cause failure in the pedestals of conventional solidity arrays. The present paper documents the heat transfer and pressure drop through two high solidity converging rounded diamond pedestal arrays. These arrays have a 45 percent pedestal solidity. One array which was tested has nine rows of pedestals with an exit area in the last row consistent with the convergence. The other array has eight rows with an expanded exit in the last row to enable a higher cooling air flow rate. The expanded exit of the eight row array allows a 30% increase in the coolant flow rate compared with the nine row array for the same pressure drop. Heat transfer levels correlate well based on local Reynolds numbers but fall slightly below non converging arrays. The pressure drop across the array naturally increases toward the trailing edge with the convergence of the flow passage. A portion of the cooling air pressure drop can be attributed to acceleration while a portion can be attributed to flow path losses. Detailed array static pressure measurements provide a means to develop a correlation for the prediction of pressure drop across the cooling channel. Measurements have been acquired over Reynolds numbers based on exit flow conditions and the characteristic pedestal length scale ranging from 5000 to over 70,000.

The solution of heat-transfer problems by the Wiener—Hopf technique II. Trailing edge of a hot film

1974 ◽  
Vol 337 (1610) ◽  
pp. 395-412 ◽  
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Half Plane ◽  
Dimensionless Temperature ◽  
Fluid Temperature ◽  
Trailing Edge ◽  
Boundary Layer Solution ◽  
Leading Term ◽  
Hot Film ◽  
Layer Solution

An incompressible fluid of constant thermal diffusivity k , flows with velocity u = Sy in the x -direction, where S is a scaling factor for the velocity gradient at the wall y = 0. The region — L ≤ x ≤ 0 is occupied by a heated film of temperature T 1 , the rest of the wall being insulated. Far from the film the fluid temperature is T 0 < T 1 . The finite heated film is approximated by a semi-infinite half-plane x < 0 by assuming that the boundary-layer solution is valid somewhere on the finite region upstream of the trailing edge. Exact solutions in terms of Fourier inverse integrals are obtained by using the Wiener-Hopf technique for the dimensionless temperature distribution on the half-plane x > 0 and the heat transfer from the heated film. An asymptotic expansion is made in inverse powers of x and the coefficient of the leading term is used to calculate the exact value of the total heat-transfer as a function of the length L . It is shown that the boundary layer solution differs from the exact solution by a term of order L -1/3 for large L . An expansion in powers of x for the heat transfer upstream of the trailing edge is also found. Application of the theory, together with that of Springer & Pedley (1973), to hot films used in experiments are discussed for the range of values of L(S/K) ½ , up to 20.

A Conjugate 3-D Flow and Heat Transfer Analysis of a Thermal Barrier Cooled Turbine Guide Vane

1998 ◽  
Author(s):  
Dieter E. Bohn ◽  
Volker J. Becker
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Guide Vane ◽  
Suction Side ◽  
Heat Transfer Analysis ◽  
Thermal Barrier ◽  
Trailing Edge ◽  
Flow And Heat Transfer ◽  
Turbine Guide Vane ◽  
Basic Configuration

This paper presents the numerical investigations of the flow and heat transfer of two configurations of a transonic turbine guide vane. The basic configuration is a vane with convection cooling. The second configuration is additionally coated with a thermal barrier consisting of ZrO2. The results are obtained with a conjugate heat transfer and flow computer code that has been developed at the Institute of Steam and Gas Turbines. Measurement data is available for the basic configuration and the computational results are compared to the experimental results. The results show very good agreement between calculated and measured vane surface temperatures. The trailing edge turns out to be subjected to high thermal loads as it is too thin to be cooled effectively. Secondary flow phenomena like the passage vortex and the corner vortex and their impact on the temperature distribution are discussed. The ZrO2 coating is calculated for a thickness of 300μm. The substrate material temperatures are lowered by about 20 K–29 K in the stagnation point area and by about 27 K–43 K in the shock area on the suction side. At the trailing edge, the coating on the suction side and on the pressure side hardly influences the metal temperature.

LES and Hybrid RANS/LES of a Fundamental Trailing Edge Slot

2014 ◽  
Author(s):  
Elizaveta Ivanova ◽  
Gregory M. Laskowski
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Numerical Study ◽  
Mixing Layer ◽  
Detached Eddy Simulation ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This paper presents the results of a numerical study on the predictive capabilities of Large Eddy Simulation (LES) and hybrid RANS/LES methods for heat transfer, mean velocity, and turbulence in a fundamental trailing edge slot. The geometry represents a landless slot (two-dimensional wall jet) with adjustable slot lip thickness. The reference experimental data taken from the publications of Kacker and Whitelaw [1] [2] [3] [4] contains the adiabatic wall effectiveness together with the velocity and the Reynolds-stress profiles for various blowing ratios and slot lip thicknesses. The simulations were conducted at three different lip thickness and several blowing ratio values. The comparison with the experimental data shows a general advantage of LES and hybrid RANS/LES methods against unsteady RANS. The predictive capability of the tested LES models (dynamic ksgs-equation [5] and WALE [6]) was comparable. The Improved Delayed Detached Eddy Simulation (IDDES) hybrid method [7] also shows satisfactory agreement with the experimental data. In addition to the described baseline investigations, the influence of the inlet turbulence boundary conditions and their implication for the initial mixing layer and heat transfer development were studied for both LES and IDDES.

Letterbox Trailing Edge Heat Transfer: Effects of Blowing Rate, Reynolds Number, and External Turbulence on Heat Transfer and Film Cooling Effectiveness

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
N. J. Fiala ◽  
I. Jaswal ◽  
F. E. Ames
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Suction Surface ◽  
Trailing Edge ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Adiabatic Effectiveness

Heat transfer and film cooling distributions have been acquired for a vane trailing edge with letterbox partitions. Additionally, pressure drop data have been experimentally determined across a pin fin array and a trailing edge slot with letterbox partitions. The pressure drop across the array and letterbox trailing edge arrangement was measurably higher than for the gill slot geometry. Experimental data for the partitions and the inner suction surface region downstream from the slot have been acquired over a four-to-one range in vane exit condition Reynolds number (500,000, 1,000,000, and 2,000,000), with low (0.7%), grid (8.5%), and aerocombustor (13.5%) turbulence conditions. At these conditions, both heat transfer and adiabatic film cooling distributions have been documented over a range of blowing ratios (0.47≤M≤1.9). Heat transfer distributions on the inner suction surface downstream from the slot ejection were found to be dependent on both ejection flow rate and external conditions. Heat transfer on the partition side surfaces correlated with both exit Reynolds number and blowing ratio. Heat transfer on partition top surfaces largely correlated with exit Reynolds number but blowing ratio had a small effect at higher values. Generally, adiabatic film cooling levels on the inner suction surface are high but decrease near the trailing edge and provide some protection for the trailing edge. Adiabatic effectiveness levels on the partitions correlate with blowing ratio. On the partition sides adiabatic effectiveness is highest at low blowing ratios and decreases with increasing flow rate. On the partition tops adiabatic effectiveness increases with increasing blowing ratio but never exceeds the level on the sides. The present paper, together with a companion paper that documents letterbox trailing edge aerodynamics, is intended to provide engineers with the heat transfer and aerodynamic loss information needed to develop and compare competing trailing edge designs.

The effect of single-sided ribs on heat transfer and pressure drop within a trailing edge internal channel of a gas turbine blade

2021 ◽  
pp. 1-43
Author(s):  
Suhyun Kim ◽  
Seungwon Suh ◽  
Seungchan Baek ◽  
Wontae Hwang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Secondary Flow ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Sharp Corner ◽  
Trailing Edge ◽  
Edge Channel ◽  
Ribbed Channel

Abstract Convective cooling in a gas turbine blade internal trailing edge channel is often insufficient at the sharp trailing edge. This study examines convective heat transfer and pressure drop within a simplified trailing edge channel. The internal passage has been modeled as a right triangular channel with a 9&amp;#176; angle sharp corner. Smooth baseline and ribbed copper plates were heated from underneath via a uniform heat flux heater and examined via infrared thermography. Non-uniformity in the heat flux due to conduction is corrected by a RANS conjugate heat transfer calculation, which was validated by the mean velocity, friction factor, and temperature fields from experiments and LES simulations. Nusselt number distributions illustrate that surface heat transfer is increased considerably with ribs, and coupled with the vortices in the flow. Heat transfer at the sharp corner is increased by more than twofold due to ribs placed at the center of the channel, due to secondary flow. The present partially ribbed channel utilizes secondary flow toward the corner, and is presumed to have better thermal performance than a fully ribbed channel. Thus, it is important to set the appropriate rib length within the channel.

scholarly journals Effects of Channel Outlet Configuration and Dimple/Protrusion Arrangement on the Blade Trailing Edge Cooling Performance

2019 ◽  
Vol 9 (14) ◽  
pp. 2900
Author(s):  
Qi Jing ◽  
Yonghui Xie ◽  
Di Zhang
Keyword(s):  
Heat Transfer ◽  
Turbine Blades ◽  
High Heat ◽  
Wake Flow ◽  
Internal Cooling ◽  
Trailing Edge ◽  
Cooling Channels ◽  
High Heat Transfer ◽  
Channel Outlet ◽  
Staggered Arrangement

The trailing edge regions of high-temperature gas turbine blades are subjected to extremely high thermal loads and are affected by the external wake flow during operation, thus creating great challenges in internal cooling design. With the development of cooling technology, the dimple and protrusion have attracted wide attention for its excellent performance in heat transfer enhancement and flow resistance reduction. Based on the typical internal cooling structure of the turbine blade trailing edge, trapezoidal cooling channels with lateral extraction slots are modeled in this paper. Five channel outlet configurations, i.e., no second passage (OC1), radially inward flow second passage (OC2), radially outward flow second passage (OC3), top region outflow (OC4), both sides extractions (OC5), and three dimple/protrusion arrangements (all dimple, all protrusion, dimple–protrusion staggered arrangement) are considered. Numerical investigations are carried out, within the Re range of 10,000–100,000, to analyze the flow structures, heat transfer distributions, average heat transfer and friction characteristics and overall thermal performances in detail. The results show that the OC4 and OC5 cases have high heat transfer levels in general, while the heat transfer deterioration occurs in the OC1, OC2, and OC3 cases. For different dimple/protrusion arrangements, the protrusion case produces the best overall thermal performance. In conclusion, for the design of trailing edge cooling structures with lateral slots, the outlet configurations of top region outflow and both sides extractions, and the all protrusion arrangement, are recommended.

Sign in / Sign up

Export Citation Format

Share Document