scholarly journals Physico-Chemical and Microbiological Qualities of Water From Wells, Drillings and Tanks Used as Drinking Water in the Municipality of Allada (Benin, West Africa)

2017 ◽  
Vol 13 (15) ◽  
pp. 69
Author(s):  
Sohounou Marc ◽  
Vissin Expédit Wilfrid ◽  
Sintondji Luc Olivier ◽  
Houssou Christophe S. ◽  
Agbossou K. Euloge ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Drinking Water ◽  
Water Source ◽  
Total Dissolved Solids ◽  
Physicochemical Analysis ◽  
High Concentration ◽  
Dissolved Solids ◽  
Physico Chemical ◽  
High Turbidity

Water, source of life, is also a source of disease when it is polluted. The aim of this study is to analyze the physicochemical quality and the bacteriological quality of the wells, boreholes and tank for drinking water in the Commune of Allada. The methodology is based on the collection of data, data processing and analysis carried out at the Laboratory for Quality Control of Water and Food (LCQEA) of the Ministry of Health. From the water sampling carried out at three (03) traditional wells, two (02) boreholes, two (02) tanks and water of river (02), bacteriological and physicochemical analysis were performed. The results showed that pH is higher at the tank than other water sources. Well 3 (P3) has a very high electrical conductivity (EC) which was 384.95 μS / cm and 192.47 mg / L for total dissolved solids (TDS). The tank 2 exhibited high value in pH 9.14; 71.72 (μS / cm) for the electrical conductivity (CE) and 35.86 mg / L, in total dissolved solids (TDS). Well 2 (P2) has a high turbidity of 4.53 (NTU) at all analyzed water points. The concentration of iron, copper nickel and cobalt remains low(less than 0.4 mg / L).Wells 2 and tank 1 are concentrated in lead, respectively 20.75mg / L and 13.71mg / L. Tank 1 and 2 have a high concentration of cadmium compared to other water points. The presence of Escherichia coli with a high concentration at home SONEB (39 CFU) and at well 2 (7.10 2 ) was found. In view of these results some recommendations were made.

The Prediction and Evaluation of the Groundwater Quality of Taikang Formation in Tertiary in West of Daqing Oilfield by Using Resistivity Logging Data

2013 ◽  
Vol 726-731 ◽  
pp. 3538-3541
Author(s):  
Kun Xiao ◽  
Chang Chun Zou ◽  
Biao Xiang
Keyword(s):  
Drinking Water ◽  
Groundwater Quality ◽  
Total Dissolved Solids ◽  
Formation Water ◽  
The South ◽  
High Quality ◽  
Dissolved Solids ◽  
Well Location ◽  
Resistivity Logging

In order to research the groundwater quality of the Taikang Formation in Tertiary in west of Daqing Oilfield, resistivity logging data of 140 wells in the study area were analyzed to forecast the groundwater total dissolved solids (TDS) distribution of the plane. When the resistivity logging value (Rt) of the Taikang Formation in Tertiary is above 45Ω.m and its corresponding value of Formation water TDS is below 1000 mg/L, the quality of groundwater accords with life standards for drinking. The south area of Hongweixing well area and the east of Xishuiyuan well area, including Ranghulu, Qianjincun, Dulitun and Nanshuiyuan well area are favorable for high quality groundwater. The research provides the evidences to evaluate the groundwater quality in west Daqing Oilfield and determine specific well location, improving the efficiency of exploring the underground drinking water.

scholarly journals RESPONSE SURFACE METHODOLOGY VIA DESIRABILITY FUNCTION TECHNIQUES FOR OPTIMIZING CORRELATED RESPONSES OF ELECTRICAL CONDUCTIVITY AND TOTAL DISSOLVED SOLIDS OF SELECTED BOREHOLE WATER

2020 ◽  
Vol 4 (3) ◽  
pp. 333-342
Author(s):  
KEHINDE MONSURU YUSUFF ◽  
M. Lawal ◽  
A. T. Audu ◽  
O. A. Wale-Orojo
Keyword(s):  
Water Quality ◽  
Electrical Conductivity ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Water Source ◽  
Total Dissolved Solids ◽  
Quality Parameters ◽  
Water Quality Parameters ◽  
Physical Parameters ◽  
Dissolved Solids

The health benefits in the description and observation of quantitative contents of quality parameters present or contained in any water source cannot be underestimated as they determine selection of best choice from available water sources for different intended uses as well as resource consumption. It also helps to compare the observed quantity of the quality with the acceptable standards or limits to get desired results. Physical parameters like pH, temperature, electrical conductivity (EC) and total dissolved solids (TDS) among others are determined by present of other chemical properties like Cations (Mg2+, Ca2+, Na+, etc), Anions (Cl-, NO3-, SO42+, etc), heavy metals and other dissolved materials during the course of its formation in different proportions and amounts. This study observed EC and TDS of 20 selected boreholes as two close and correlated water quality parameters as well as two of the major water quality parameters that account for overall quality of any water source, despite their different quantitative contents and physical features, they are likely determined by the same set of cations and anions with similar constraint equations. In contrast to linear programming, multiple criteria optimization models were fitted for EC and TDS using Response Surface Methodology via desirability techniques, optimal values obtained in this case measured against several criteria are found to lie between acceptable standards limits for drinking water, other numerical values and descriptive features in the final results reflect that the response equations obtained were well fitted.

scholarly journals Bacteriological and physical quality of fiche drinking water from households and reservoirs, Oromia, Ethiopia

2021 ◽  
Author(s):  
Israel Sebsibe ◽  
Birhanu Degaga ◽  
Gezahegn Feye ◽  
Tsige Tekle
Keyword(s):  
Electrical Conductivity ◽  
Drinking Water ◽  
Experimental Analysis ◽  
Total Dissolved Solids ◽  
Fecal Coliforms ◽  
World Health ◽  
Wet Season ◽  
Dissolved Solids ◽  
Total Coliforms ◽  
Water Handling

Abstract Drinking water is the major source of bacteria pathogens in developing countries along with poor sanitation and contamination of food with a pathogen. More than half of the population of the country uses unimproved sanitation facilities while 36% of them practiced open defecation. The aim of the study was to investigate the suitability of public water for drinking. The study is designed to include a survey of 90 respondents and experimental analysis of 170 water samples from households and reservoirs. Water quality parameters, such as temperature, electrical conductivity, turbidity, total dissolved solids, and bacteriological parameters like total coliforms (TC) and fecal coliforms (FC) were determined. Many of the respondents (88.8%) remarked that the water has no smells, tastes, and color. The experimental analysis confirmed that temperature (19.7 °C), electrical conductivity (269.63 μS/cm), turbidity (1.17 NTU), and total dissolved solids (134.3 mg/L) were found below the prescribed limit of World Health Organization guidelines for drinking water. Total coliforms (9.29 CFU/100 mL) and fecal coliforms (5.07 CFU/100 mL) were detected from pipe water sources during the wet season showing non-compliance with the guidelines. The reservoir samples were free from bacterial contamination. The main point of drinking water contamination was the household where unsafe water handling practice was a common habit in the study area. Hence, awareness conception training on safe water handling practices is highly recommended for the communities.

scholarly journals Comparative Analysis of Physico-Chemical Parameters of Borehole, Pond and Well Water in Kashere Metropolis

2017 ◽  
Vol 2 (6) ◽  
pp. 42
Author(s):  
Abdulkadir A. Gidado ◽  
Ibrahim Halliru ◽  
Christiana Anawuese Kendeson ◽  
Yusuf Abdullahi
Keyword(s):  
Drinking Water ◽  
Water Samples ◽  
Standard Procedure ◽  
Human Consumption ◽  
Chemical Parameters ◽  
Quality Of Water ◽  
Major Cations ◽  
Physico Chemical ◽  
High Turbidity

In a bid to ascertain the quality of water for human consumption in Kashere Metropolis, essential physico-chemical parameters were evaluated on samples of drinking water obtained from boreholes, pond and wells located at densely populated areas, labelled as: Kashere cattle market Pond, KP; Kashere cottage Hospital Borehole, HB; Kashere Market Borehole, MB; Federal University, Kashere (FUK) campus Borehole, CB; Kashere cottage Hospital Well, HW; Kashere Market Well, MW and FUK campus Well, CW. Standard procedure for the determination of chemical and physical characteristics of the water samples were used. The results of the investigated parameters in the samples were as follows: ρH 6.61‒7.96, Turbidity 0.0‒2568 FTU, Electrical Conductivity 60.5‒1151 Mhocm-1, Total Dissolved Solids (TDS) 25.9‒518.0 mgL-1, Ca 0.0033‒0.5446 ppm, Mg 0.0793‒1.2215 ppm, Cd 0.0010‒0.0030 ppm, Zn 0.0024‒0.l054 ppm, Pb 0.0002‒0.0026 ppm and Fe 0.0044‒0.5649 ppm. Except for the concentration of Fe (in CB; 0.5649 ppm), all the analyzed minor and major cations in the water samples were in very low concentration and below the permissible limits of WHO standard guidelines values for drinking water.  It is recommended that, water from the pond should be properly treated before consumption due to its high turbidity.  Also periodic assessment of the quality of drinking water from these water sources should be conducted, to ascertain that they are not contaminated by either or both organic and inorganic pollutants.

scholarly journals Assessment of Groundwater Quality in Parts of Ijoko Area, Sango-Otta Axis of Southwestern Nigeria

2019 ◽  
pp. 103-111
Author(s):  
Victoria Abiola Dairo ◽  
Victor Oludare Fagoyinbo ◽  
Godson Mac-tyger
Keyword(s):  
Electrical Conductivity ◽  
Drinking Water ◽  
Water Samples ◽  
Ph Value ◽  
High Concentration ◽  
Southwestern Nigeria ◽  
Major Cations ◽  
Physico Chemical ◽  
Irrigation Purpose ◽  
Total Dissolved Solid

A total of 26 water samples comprising of well, river and borehole waters were subjected to physico-chemical tests to evaluate its quality. The result of the physical characteristics shows that the average pH value, total dissolved solid and electrical conductivity is 4.9, 1027.31mg/L and 1526.92mg/L respectively. Thus, relatively above the desirable limit for drinking water while the ionic dominance of the major cations and anions reveal high concentration of Na+ and Cl- amidst other ions in the order of Na+>Ca2+>Mg2+> K+ and Cl->HCO3- > SO42- respectively wherein the water was classified as belonging to Na-Cl facies and unsuitable for irrigation purpose.

scholarly journals Analysis of Ground Water from Selected Sources in Jalingo Metropolis, Nigeria

2021 ◽  
Author(s):  
Benjamin Ezekeil Bwadi ◽  
Mohammed Bakoji Yusuf ◽  
Ibrahim Abdullahi ◽  
Clement Yakubu Giwa ◽  
Grace Audu
Keyword(s):  
Electrical Conductivity ◽  
Drinking Water ◽  
Dissolved Oxygen ◽  
Physicochemical Properties ◽  
Ground Water ◽  
Waste Disposal ◽  
Chemical Properties ◽  
Total Dissolved Solids ◽  
Dissolved Solids ◽  
Mean Values

Water is very significant in the development of a stable community, but many societies are confronted with the challenges of poor wastes management system with indiscriminate waste disposal and bad land practices, which easily pollute water sources and consequently degrade water quality. This study was to analyze the physicochemical properties of ground water from multiple point sources in Jalingo, Taraba state of Nigeria. Water samples were collected from twenty seven (27) sites from the study area during the raining and dry seasons. The analysis was carried out to determining the physico-chemical properties of the ground water and comparing with the World Health Organization (WHO) standard for drinking water. The physicochemical properties of ground water analyzed include; odor, taste, temperature and electrical conductivity were tested in the field using water meter tester. Whereas pH, total dissolved solids, alkalinity, hardness, salinity, iron, manganese, fluoride, nitrate, nitrite, chloride, sulphate and dissolved oxygen were analyzed in the laboratory using Wagtech potable water testing equipment. The physical properties of water analyzed were temperature, odor, taste, and turbidity. Whereas the chemical properties of water analyzed were pH, electrical conductivity (EC), total dissolved solids (TDS), alkalinity, hardness, salinity, iron (Fe), manganese (Mn), fluoride (F−), nitrate (NO3−), nitrite (NO2−), Chloride (Cl−), sulphate (SO42−), dissolved oxygen (DO).The result shows the range of the mean values of the temperature(26.7–33.1) oC, p H(6.5–8.9), Fe (0.01–0.08 mg/L), NO3−(0.01–38.5 mg/l), NO2−(0.01–0.09 mg/l), Mn (0.01–0.17 mg/l), F(0.01–0.82 mg/l), alkalinity(39-204 mg/l), salinity (42-508 mg/l), SO4(14-93 mg/l), total dissolved solids (6–637) mg/l, turbidity(0.4–10.6 mg/l), hardness(48-187 mg/l), and fecal coliforms(1–4)fcu/100mi, dissolved oxygen(1.1–6.87)mg/l, EC(10.99–1066)ohm/cm, Cl (10-320 mg/l). All except alkalinity and hardness are within the WHO permissible standards of quality drinking water. The highest alkalinity (204 mg/l), hardness (187 mg/l) and low dissolved oxygen (6.87 mg/l) attributed to the high concentration of dissolved salts and basic cations in the water. The methodology applied in the study was effective in analyzing the physicochemical properties of water in the study area. Therefore, it was recommended that there should be frequent water source testing by stakeholder in water resources with the view to treating the water. Policy maker should also enforce the regulation of the use of chemical fertilizers, agro-chemicals and the indiscriminate waste disposal.

scholarly journals Physicochemical Analysis of Ground Water Samples of South Coastal Areas of Kanniya kumari in the Post-Tsunami Scenario

2016 ◽  
Vol 13 (2) ◽  
pp. 116-121
Author(s):  
Krishna Arunachalam ◽  
Monikandon Sukumaran ◽  
Mohammad Tanveer ◽  
Kesavan Devarayan
Keyword(s):  
Electrical Conductivity ◽  
Ground Water ◽  
Physicochemical Parameters ◽  
Tamil Nadu ◽  
Total Dissolved Solids ◽  
Physicochemical Analysis ◽  
Total Hardness ◽  
Sodium Potassium ◽  
Calcium Magnesium

In this study, the effect of ‘natural/self cleaning’ of ground water by precipitation after a decade of tsunami is evaluated along the coast of Kanniyakumari district, Tamil Nadu, India. The samples were collected from five stations namely Colachel, Muttom, Periyakadu, Manakudy, and Kanniyakumari. The physicochemical parameters such as turbidity, total dissolved solids, electrical conductivity, pH, alkalinity, total hardness, calcium, magnesium, sodium, potassium, chloride, and fluoride were evaluated and compared with the database of the pre-tsunami sample collected in 2004. The results indicated that the ‘natural cleaning’ has improved the quality of the ground water over the years after tsunami.

Water Quality of Surface Runoff from Grazed Fescue Grassland Watersheds in Alberta

2002 ◽  
Vol 37 (3) ◽  
pp. 543-562 ◽  
Author(s):  
Emmanuel Mapfumo ◽  
Walter D. Willms ◽  
David S. Chanasyk
Keyword(s):  
Water Quality ◽  
Electrical Conductivity ◽  
Organic Carbon ◽  
Surface Runoff ◽  
Total Dissolved Solids ◽  
Total Carbon ◽  
Runoff Water ◽  
Dissolved Solids ◽  
Heavy Grazing

Abstract A study was conducted at Stavely Research Station, Alberta, to determine the quantity and quality of surface runoff from small grassland watersheds under three grazing intensities, viz. ungrazed, heavy grazing (2.4 animal unit months per hectare, AUM ha-1) and very heavy grazing (4.8 AUM ha-1). The volume of surface runoff varied each year (1998, 1999 and 2000) and also differed across watersheds, with lower runoff in the ungrazed compared with the heavy and very heavy grazed watersheds. Total dissolved solids in surface runoff water ranged between 34 to 360 mg L-1, and that for runoff from the very heavy grazed watershed was greater than that from other watersheds. Electrical conductivity increased with increased grazing intensity on the watershed. In two of three years the very heavy grazed watershed had greater nitrate concentrations than the other two watersheds. In all three years the levels of nitrate were lower than the maximum acceptable level for drinking water (10 mg L-1 as nitrogen). Levels of orthophosphate (PO43-) in surface runoff from all three watersheds and the three years of study were less than 1 mg L-1, and mostly within the range considered typical for rivers and streams. Total carbon (up to 500 mg L-1) was greater than the amounts considered typical for streams and rivers, and most of it was organic carbon. Nuisance organisms such as algae, nematodes, Giardia spp., Cryptosporidium spp. and rotifers were detected in some surface runoff samples. However, no crustaceans were detected. The results of a canonical correlation analysis indicated that the dominant external forcing factors (meteorological and management) in influencing water quality were year of study, water temperature and grazing. Surface runoff discharge did not influence water quality measurements. The dominant water quality parameters were found to be total carbon, organic carbon, total dissolved solids and electrical conductivity. Overall, this study indicated that during the three years, the surface runoff volumes from the watersheds were small and grazing of these watersheds posed little risk of nutrient (e.g., nitrate, ammonia and orthophosphate) contamination of adjacent streams, but organic carbon loading and dissolved solids may be of concern. The presence of parasites was detected in two or less runoff water samples each year, and thus pose little risk of contamination of adjacent streams. However, it may be necessary to monitor parasites especially in areas under cow-calf operations.

scholarly journals Optimization of ozone decomposition time and its effect on physicochemical and bacteriological quality of table water

2019 ◽  
Vol 11 (1) ◽  
pp. 131-134
Author(s):  
Ogueri Nwaiwu ◽  
Vincet Ifeanyi Ibekwe
Keyword(s):  
Process Optimization ◽  
Water Source ◽  
Total Dissolved Solids ◽  
Bottled Water ◽  
Water Disinfection ◽  
Ozone Decomposition ◽  
Dissolved Solids ◽  
Significant Difference ◽  
Decomposition Time

Ozone is widely used in water disinfection and the concentration needed for the effective microbial elimination depends on the water source. In many bottled water producing industries, products containing ozone are quarantined after application to allow decomposition into diatomic oxygen molecules and oxygen atoms in order to eliminate any toxic effect. A process optimization was carried out to determine the ozone decomposition time in a table water producing factory in southern Nigeria. To this end, bottled water products injected with the ozone were collected from a bottling line immediately after production and monitored for ozone decomposition. Parameters like total dissolved solids, temperature and pH were determined and bacteriological analyses for total bacteria count and presence of Pseudomonasand coliforms were carried out. It was found that the ozone half-life was under 30 minutes and was no longer detectable after two and a half hours. For all analyzed stored products, the pH was in the range of 7.0-7.06, while the temperature was between 23 and 25 °C. The total dissolved solids ranged from 0.05 to 0.09 mg/mL, and there was no significant difference (p> 0.05) for the bottled products stored for 24 or 48 hours after the production. No bacteria weredetected. The shorter quarantine period allows quicker distribution and highlights the importance of ozone decomposition testing for the process optimization, especially if equipment or water source change over time.

scholarly journals Determination of Heavy elements in Drinking Water from Different Regions of Baghdad City (Iraq) Using EDXRF Spectrometer

2017 ◽  
Vol 28 (1) ◽  
pp. 142
Author(s):  
Muhanad H. Alrakabi ◽  
Esraa S. Ramadan
Keyword(s):  
Electrical Conductivity ◽  
Drinking Water ◽  
World Health Organization ◽  
Total Dissolved Solids ◽  
Permissible Limit ◽  
International Standards ◽  
World Health ◽  
Dissolved Solids ◽  
Who Standards ◽  
Health Organization

It was calculated the average concentrations of elements manganese, iron, cobalt, nickel, copper, zinc, arsenic, cadmium and lead in the sixteen samples of drinking water (tap water), were collected from different areas in the Baghdad city. The Results indicated that the average of concentrations of the elements Mn, Fe, Pb, Ni and Cd (0.44ppm, 0.49ppm, 0.04ppm, 0.17ppm and 1.2ppm respectively) higher than permissible limit while the concentrations of elements Cu and Zn (0.11ppm and 0.14ppm respectively) were lower than the permissible limit of World Health Organization (WHO) standards (1ppm and 3ppm) respectively for drinking water and the concentration of Arsenic in the nuclear lab sample in college of sciences - Mustansiriyah University was higher than permissible limit. All the drinking water samples were analyzed and determined the physical and chemical properties such as Electrical Conductivity (EC), pH, and Total Dissolved Solids (TDS). The highest value was (1064μS/cm) in Al-Tuwaitha sample and the lowest value (531μS/cm) in Al-Sadr City (Sector 7) sample for the Electrical Conductivity. The pH values ranged from (7.0-8.2). The average levels of Total Dissolved Solids (TDS), the highest value was 550 mg/L in the Diyala Bridge sample while the lowest value 276mg/L in Al-Sadr City (Sector 7) sample. The results were compared with national and international standards, and it’s also showed that the values of the parameters within the permissible limit of World Health Organization (WHO) standards, except the Electrical Conductivity values for some samples were higher than permissible limit. According to these results, all the water projects must be monitored as well as using the proper and modern techniques for treatment the drinking water.

Sign in / Sign up

Export Citation Format

Share Document