scholarly journals OBSERVASI HASIL PELEDAKAN MENGGUNAKAN METODE PELEDAKAN NONEL DAN ELECTRONIC DETONATOR

2020 ◽  
Vol 6 (2) ◽  
pp. 117
Author(s):  
Ahmad Rizani ◽  
Kartini Kartini ◽  
Khairunnisa Umar
Keyword(s):  
Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Pengfei Zhang ◽  
Runcai Bai ◽  
Xue Sun ◽  
Haoran Li ◽  
Honglu Fei ◽  
...  

To improve the productivity and efficient of modern large-scale open-cut mines, a number of technologies are developed and trialed, including new blasting equipment, larger blasting holes, high benches, air spacing, and short-delay blasting within holes. However, the relative blasting parameters need field calibration and further investigation of theories on these techniques are required. This paper studied the open-cut bench blasting at Barun Eboxi Mine of Baotou Iron and Steel Group via theoretical analysis on shock wave, numerical simulation, and field test. According to the technical conditions of the site, three sets of vertical boreholes at 310 mm diameter were drilled on 24 m high batter; and three sets of air-spaced charges were set up. The digital electronic detonator was used to initiate at millisecond intervals. The study found that under the condition of 24 m high bench, the use of intermediate air interval is beneficial to the rock fragmentation. The delay time within the hole is 3-8 ms. The bottom of the lower explosives and the top of the upper explosives were devised for initiation to optimize the initiation location. The peak effective stress points are 63.6%, 52.2%, and 8.9% higher, respectively. The field test of high-bench intrahole millisecond blasting in Barun Eboxi mine shows that the intrahole millisecond blasting parameters proposed in this study are feasible.


2019 ◽  
Vol 134 ◽  
pp. 01017
Author(s):  
Igor Katanov ◽  
Sergey Kondratyev ◽  
Andrey Sysoyev

The topicality of the present work lies in justification of the means of increasing safety during mass explosions in opencasts. The solution to this problem is possible due to the orientation of downholes in the array, taking into account the angle of incidence and extension of the strata, high-quality stemming and initiation of downhole charges by delay detonators with a minimal deviation from nominal values of their firing time. The most promising way to increase the safety and efficiency of blasting is an integrated approach, including drilling downholes, normal to the strata, and using the design of the downhole charge, rationally distributing the explosion energy in the space of the rock mass due to the use of stemming of a variable density, low-density gap between the parts of the explosive charge and the bottom a downhole compensator based on foam gel and the use of hybrid electronic detonator Iskra-T.


Fragblast ◽  
2003 ◽  
Vol 7 (1) ◽  
pp. 13-22 ◽  
Author(s):  
Douglas A. Bartley ◽  
Robert McClure
Keyword(s):  

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Weijie Ding ◽  
Bei Jia ◽  
Dianshu Liu

Blasting excavation is extensively used in tunnel construction, and the adverse effect of ground vibration induced by blasting on surrounding structures and inhabitants is a critical problem. This study aims to investigate the tunnel hollow effect on triaxial peak particle velocities (PPV) and dominant frequencies induced by electronic detonator. Field experiments were conducted in a shallow tunnel construction site and the ground vibration waveforms were recorded. Variational mode decomposition (VMD) was applied to denoise and correct the zero-drift phenomenon, and the proposed method of selecting the optimal parameter was verified. A series of statistical analyses and tests were performed to evaluate the differences of peak particle velocity and dominant frequency among various monitoring points. The results showed that the hollow effect on Z-axis PPV is significant, and triaxial PPV is also affected when the horizontal distance exceeds 30 m. The hollow effect on dominant frequency could not be identified since the hollow of tunnel is a free face, and the dominant frequency of reflected wave remains unchanged. An augmented factor of 1.229 is determined carefully as the hollow effect factor on PPV. Therefore, blasting vibration induced by electronic detonator of the excavated zone should be attached with greater importance, and hollow effect on PPV should be considered in the blasting design of tunnel excavation.


2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Zhen Lei ◽  
Qing Chen ◽  
Wen Zhao ◽  
Yu-Jing Li ◽  
Zheng-Hua Gao

To ensure the safe and efficient excavation of ultradeep foundation pits in a complex urban environment, the ultradeep foundation pit excavation project of Liuguangmen Urban Complex in Guiyang City was taken as the study point. A high-efficiency blasting method was proposed for the excavation of vibration-isolating slot and electronic detonators, and a three-dimensional spatial calculation model of the foundation pit structure was established. In addition, the field test and numerical simulation of the blasting vibration were developed. The feasibility of the high-efficiency blasting method was demonstrated, and the propagation law of the dynamic response characteristic parameters of the structure was explored using an electronic detonator and vibration-isolating slot. The results show that the electronic detonator carried out peak shaving within the group, unloading waves between the groups, and the blocking effect of the vibration-isolating slot, and all these effectively reduced the peak stress and peak particle vibration velocity, evenly distributed the vibration velocity, and guaranteed the safety of the surrounding existing buildings, proving the feasibility of the efficient blasting method. There is a “wall effect” at the supporting pile, whose propagation velocity is lower than that inside the rock mass, and the PPV is radial X > tangential Y > vertical Z. The peak values of stress, strain, and PPV all decrease with increasing supporting pile height, and there is an inflection point at 20 m. The internal nodes of the pile reciprocate without sharp change and failure in displacement. The peak displacement of different nodes is in the order X > Y > Z with increasing pile height, and the maximum peak value is 0.08 mm.


2013 ◽  
Vol 850-851 ◽  
pp. 332-337
Author(s):  
Wei Feng Cheng ◽  
Zhen Yu Wang ◽  
Yin Lu Chen ◽  
Guo Hua Liu

Excavation blasting has a great impact on the buildings, therefore, it is important to control blasting vibrations. In this paper, based on the time-energy density analysis and wavelet packet analysis for measured data of blasting vibrations, some useful results can be concluded. Firstly, the energy of Millisecond Detonator Blasting (MDB) vibration signals in the 0~200Hz band accounts for 90.06% of the total energy, and its advantage energy mainly distribute in low-frequency band. However, the energy of Digital Electronic Detonator Blasting (DEDB) vibration signals in the 0~600Hz band is 96.08% of the total energy, its advantage energy mainly distribute in wider band. Moreover, the time-energy density curve of DEDB doesnt have the abrupt and separated fluctuation, which indicates the interference and superposition of DEDB are very distinct. The controlled DEDBs and tunnel support measures of this project have achieved a good effect. The comprehensive benefits are remarkable and it has an important significance for improving the level of blasting technology.


2012 ◽  
Vol 482-484 ◽  
pp. 1785-1788
Author(s):  
Hong Yue Li ◽  
Zhao Quan Chen ◽  
Feng Liu ◽  
Shi Long Yan

A design proposal for a kind of online programming electronic detonator is introduced in this paper. The safety and reliability of the design is analyzed, and then the methods for realizing the design proposal are exploited. The structure of the electronic detonator, the internal control circuit structure diagram, and part of the software flowchart, are presented. The time programmable increment step of 1 millisecond is arrived at, while the programmable delay time of this system ranging from 1 to 12000 milliseconds is obtained. Taking its safety and reliability, its accuracy in delay time, and its easy of use, into account, the online programming electronic delay detonator proposed in this paper will be extensively applicable to complicated blasting engineering in the future.


Sign in / Sign up

Export Citation Format

Share Document