scholarly journals History of hydrocarbon exploration in the Kurdistan Region of Iraq

GeoArabia ◽  
2015 ◽  
Vol 20 (2) ◽  
pp. 181-220
Author(s):  
David S. Mackertich ◽  
Adnan I. Samarrai

ABSTRACT The Kurdistan Region of Iraq has witnessed extraordinary levels of exploration activity since the first exploration well to be drilled in over two decades was spudded in 2005. Since then almost 200 wells have been drilled encountering recoverable reserves estimated to be in excess of 15 billion barrels of oil equivalent. Whilst the region is in close proximity to many of the giant and supergiant fields of Iran and Iraq, the reservoirs in which discoveries have been made are largely different. In Iraq a large percentage of discovered reserves reside in Cenozoic and Cretaceous sediments capped by Cenozoic evaporite sequences. Over much of Kurdistan, particularly the north and northeastern parts of the region, Cenozoic strata are absent. A decade ago many were doubtful that significant quantities of hydrocarbons could be trapped in the absence of the Cenozoic evaporite sequences. Furthermore, whilst the presence of large surface structures and significant oil seeps were encouraging to some, to others it fueled concerns about trap leakage. Today the majority of the surface anticlinal features in Kurdistan have been drilled, but remain to be fully evaluated. Almost all of the exploration activity in Kurdistan has taken place on 2-D seismic with vertical exploration wells. In the last few years, a number of 3-D seismic surveys have been acquired and these will undoubtedly lead to production and reserve enhancements in parallel with increased subsurface complexity. Following a decade of exploration, three fields have been fully appraised and have a reasonable early production history: Tawke, Taq Taq and Khurmala. Reserve additions in the Tawke Field have been significant as a result of increased production performance due to better than originally anticipated reservoir properties, better pressure communication and additional reserves found in older reservoirs. It is probable that similar trends will occur in other fields and discoveries. Whilst a small number of horizontal wells have been drilled, advanced techniques used for producing from tight fractured carbonates such as multilateral wells, hydraulic fracturing, selective completions, proping and water injection have not as yet been used in the region. Almost all wells in Kurdistan have been drilled on surface or near subsurface structures within the foreland or the fold belt. Some wells have drilled through thrusts, more often by accident as opposed to on purpose. There have been virtually no dedicated wells for pure sub-thrust plays or stratigraphic traps although hydrocarbons have been found below significant thrusts and also beyond apparent structural closure in some structures. Challenges remain in what is a structurally complex and recently deformed region. High levels of exploration and appraisal activity persist and new pipeline infrastructure is under construction. It is likely that the Kurdistan Region of Iraq will develop to become an important contributor to world oil and gas production. This paper aims to summarise the first decade of exploration and appraisal activity in Kurdistan Region of northern Iraq. Due to the paucity of technical papers on this subject, this document draws upon the authors’ own knowledge and material published by companies operating in the region.

2021 ◽  
pp. 90-110
Author(s):  
V.Ye. Shlapinskiy ◽  
H.Ya. Havryshkiv ◽  
Yu.P. Haievska

More than 6 million tons of the oil have been extracted in the Skybа Zone of the Ukrainian Carpathians. In particular, 4.2 million tons of oil (85.7% of total production) were obtained from the Yamna sandstones of Paleocene, which are characterized by satisfactory physical properties. Most of the areas of fields that exploited them are located in the Boryslav oil and gas production area. Among them are such oil fields as Skhidnytsko-Urytske (more than 3.8 million tons of oil extracted), Violeta, Faustina, MEP, Miriam and Ropne. Outside this area, oil was extracted in Strilbychi and Staraya Sol. At most of these fields, oil horizons are at a depth of only 100-800 m. The gas and condensate are extracted at the field of Tanyavа in the wing of the Vytvytska Luska of the Berehova Skyba, which has been torn off by the thrust. In addition, a very large number of natural oil and gas manifestations - direct signs of oil and gas potential - have been recorded in the Skyba Zone. All this indicates the potential prospects of structures within the Skyba Zone, including shallow ones. The distribution area of Yamna sandstones is much larger than the area of these deposits. The distribution area of sandstones of Yamna is much larger than the area of these deposits. It occupies about half of the area of Skyba Zone. Part of it can be considered promising, removing areas where of Yamna sandstones are present on the day surface, although, even in such conditions, they are in some cases industrially oil-bearing (Strelbychi oil field). Sandstones of Yamna are characterized by satisfactory reservoir properties., The calculated porosity and permeability reach the maximum values at known deposits: 0.182 and 130 ∙ 10–3 microns2 respectively, and the estimated thickness of 13.5 m. In the Folded Carpathians and, especially, within the north-eastern fragments (Beregova, Oriv, Skoliv) in different years performed a large amount of field seismic surveys. On the basis of the obtained materials, for the first time in the Carpathian region structural constructions were made on the reflecting horizons in the Paleocene (Yamna Formation) and in the Stryi Formation of the Upper Cretaceous. This article evaluates the prospects of these research objects. The Khodkiv and Osichnyanska structures of Berehova Skyba are recommended for conducting search works.


2018 ◽  
Vol 58 (1) ◽  
pp. 190
Author(s):  
Francois Bache ◽  
Paul Walshe ◽  
Juergen Gusterhuber ◽  
Sandra Menpes ◽  
Mattilda Sheridan ◽  
...  

The Neoproterozoic to Late Paleozoic-aged Amadeus Basin is a large (~170 000 km2) east–west-trending basin, bounded to the south by the Musgrave Province and to the north by the Arunta Block of the Northern Territory. Commercial oil and gas production is established in the northern part of the basin but the southern part is still a frontier exploration area. Vintage and new seismic reflection data have been used with well data along the south-eastern Amadeus Basin to construct a new structural and depositional model. Three major phases of deformation controlling deposition have been identified. The first phase is characterised by a SW–NE trending structural fabric and is thought to be older than the deposition of the first sediments identified above basement (Heavitree and Bitter Springs formations). The second phase corresponds to the Petermann Orogeny (580–540 Ma) and trends in a NW–SE orientation. The third phase is the Alice Springs Orogeny (450–300 Ma) and is oriented W–E to WNW–ESE in this part of the basin. This tectono-stratigraphic model involving three distinct phases of deformation potentially explains several critical observations: the lack of Heavitree reservoir at Mt Kitty-1, limited salt movements before the Petermann Orogeny (~300 Ma after its deposition) and salt-involved structures that can be either capped by the Petermann Unconformity and overlying Cambrian to Devonian sediments, or can reach the present day surface. Finally, this model, along with availability of good quality seismic data, opens new perspectives for the hydrocarbon exploration of the Amadeus Basin. Each of the tectonic phases impacts the primary petroleum system and underpins play-based exploration.


Author(s):  
А.А. Умаев ◽  
А-М.Б. Измаилов ◽  
Т-А.У. Мусаев ◽  
А.Ш. Халадов

Наряду с совершенствованием эксплуатации скважин и повышением продуктивности за счет работ по воздействию на призабойную зону пласта, одним из главных вопросов является повышение нефтеотдачи пласта. Актуальность этих вопросов не вызывает сомнения применительно к месторождениям Северного Кавказа. Особенные геологическиеусловия присущие продуктивным пластам Чеченской республики (большая глубина залегания, высокая температура и давление, неоднородность коллекторских свойств и т.д.) затрудняют или полностью исключают возможность применения известных методов физико-химического воздействия на пласты с целью интенсификации отборов нефти и повышения нефтеотдачи. На нефтегазодобывающих объектах ЧР применялись основные физико-химические, тепловые и гидродинамические методы повышения нефтеотдачи пластов Along with improving the operation of wells and increasing productivity due to the work on the impact on the bottomhole formation zone, one of the main issues is the increase in oil recovery. The relevance of these issues does not raise doubts in relation to the fields of the North Caucasus. The special geological conditions inherent in the productive formations of the Chechen Republic (large depth, high temperature and pressure, heterogeneity of reservoir properties, etc.) make it difficult or completely exclude the possibility of using known methods of physicochemical treatment of formations in order to intensify oil production and increase oil recovery. The main physical, chemical, thermal and hydrodynamic methods of enhanced oil recovery were used at oil and gas production facilities in the Chechen Republic


Author(s):  
Morten Lovstad ◽  
Tor G. Syvertsen

Abstract Huge steel or reinforced concrete structures in deep waters support the installations for oil and gas production in the North Sea. Steady operations in a hostile environment require that structural safety and integrity is maintained. For rapid evaluation and assessment of structural integrity in case of modifications or urgency situations, Structural Integrity Systems are established, comprising computational models and structural analysis programs. A major problem for structural assessment at short notice is to keep the analysis models updated and consistent with the actual state of the physical structure and the loadings. This paper proposes a layered approach for model integration, which enable maintenance of the models at a high level, from which detailed analysis models are derived in a consistent manner.


2020 ◽  
pp. 21-26
Author(s):  
E.H. Ahmadov ◽  

The paper studies the reduction rate of gas production in the wells of Bulla-deniz field drilled to VIII horizon. With this purpose, geological (reservoir properties, oil-gas saturation, net thickness, formation pressure and temperature, formation heterogeneity, multi-layer system, tectonic faults, physical-chemical properties of oil and gas etc.) and technological (well structure, measuring and transportation system, well operation regime, drilling technology etc.) conditions of formation were analyzed and the well model of VII and VIII horizons of Bulla-deniz field using these geological and technical parameters developed as well. For the estimation of impact of geological and technical aspects on production, sensitivity analysis was carried out on the models. The suggestions for elaboration of uncertainty of geological and technical parameters affecting production dynamics were developed. To reveal the reasons for production differences of the wells, it was proposed to install borehole manometers, to obtain the data on pressure recovery curves, drainage area, skin-effect impact, permeability and to develop a study plan of bottomhole zone with acid.


2021 ◽  
Vol 73 (09) ◽  
pp. 58-59
Author(s):  
Chris Carpenter

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper OTC 30407, “Case Study of Nanopolysilicon Materials’ Depressurization and Injection-Increasing Technology in Offshore Bohai Bay Oil Field KL21-1,” by Qing Feng, Nan Xiao Li, and Jun Zi Huang, China Oilfield Services, et al., prepared for the 2020 Offshore Technology Conference Asia, originally scheduled to be held in Kuala Lumpur, 2–6 November. The paper has not been peer reviewed. Copyright 2020 Offshore Technology Conference. Reproduced by permission. Nanotechnology offers creative approaches to solve problems of oil and gas production that also provide potential for pressure-decreasing application in oil fields. However, at the time of writing, successful pressure-decreasing nanotechnology has rarely been reported. The complete paper reports nanopolysilicon as a new depressurization and injection-increasing agent. The stability of nanopolysilicon was studied in the presence of various ions, including sodium (Na+), calcium (Ca2+), and magnesium (Mg2+). The study found that the addition of nanomaterials can improve porosity and permeability of porous media. Introduction More than 600 water-injection wells exist in Bohai Bay, China. Offshore Field KL21-1, developed by water-flooding, is confronted with the following challenges: - Rapid increase and reduction of water-injection pressure - Weak water-injection capacity of reservoir - Decline of oil production - Poor reservoir properties - Serious hydration and expansion effects of clay minerals To overcome injection difficulties in offshore fields, conventional acidizing measures usually are taken. But, after multiple cycles of acidification, the amount of soluble substances in the rock gradually decreases and injection performance is shortened. Through injection-performance experiments, it can be determined that the biological nanopolysilicon colloid has positive effects on pressure reduction and injection increase. Fluid-seepage-resistance decreases, the injection rate increases by 40%, and injection pressure decreases by 10%. Features of Biological Nanopolysilicon Systems The biological nanopolysilicon-injection system was composed of a bioemulsifier (CDL32), a biological dispersant (DS2), and a nanopolysilicon hydrophobic system (NP12). The bacterial strain of CDL32 was used to obtain the culture colloid of biological emulsifier at 37°C for 5 days. DS2 was made from biological emulsifier CDL32 and some industrial raw materials described in Table 1 of the complete paper. Nanopolysilicon hydrophobic system NP12 was composed of silicon dioxide particles. The hydrophobic nanopolysilicons selected in this project featured particle sizes of less than 100 nm. In the original samples, a floc of nanopolysilicon was fluffy and uniform. But, when wet, nanopolysilicon will self-aggregate and its particle size increases greatly. At the same time, nanopolysilicon features significant agglomeration in water. Because of its high interface energy, nanopolysilicon is easily agglomerated, as shown in Fig. 1.


2021 ◽  
pp. 1-23
Author(s):  
Daniel O'Reilly ◽  
Manouchehr Haghighi ◽  
Mohammad Sayyafzadeh ◽  
Matthew Flett

Summary An approach to the analysis of production data from waterflooded oil fields is proposed in this paper. The method builds on the established techniques of rate-transient analysis (RTA) and extends the analysis period to include the transient- and steady-state effects caused by a water-injection well. This includes the initial rate transient during primary production, the depletion period of boundary-dominated flow (BDF), a transient period after injection starts and diffuses across the reservoir, and the steady-state production that follows. RTA will be applied to immiscible displacement using a graph that can be used to ascertain reservoir properties and evaluate performance aspects of the waterflood. The developed solutions can also be used for accurate and rapid forecasting of all production transience and boundary-dominated behavior at all stages of field life. Rigorous solutions are derived for the transient unit mobility displacement of a reservoir fluid, and for both constant-rate-injection and constant-pressure-injection after a period of reservoir depletion. A simple treatment of two-phase flow is given to extend this to the water/oil-displacement problem. The solutions are analytical and are validated using reservoir simulation and applied to field cases. Individual wells or total fields can be studied with this technique; several examples of both will be given. Practical cases are given for use of the new theory. The equations can be applied to production-data interpretation, production forecasting, injection-water allocation, and for the diagnosis of waterflood-performanceproblems. Correction Note: The y-axis of Fig. 8d was corrected to "Dimensionless Decline Rate Integral, qDdi". No other content was changed.


2021 ◽  
pp. 25-38
Author(s):  
I. I. Bosikov ◽  
A. I. Mazko ◽  
A. V. Mayer ◽  
O. V. Gagarina

At the present stage, the development of the oil industry of the Russian Federation is impossible without replenishing the resource base, and therefore an urgent task is to analyze and assess the conditions and characteristics of oil-andgas content in unexplored regions.Purpose of the study is an analysis and an assessment of reservoir properties of rocks of the Aptian horizon Р1+2- К2 within the Akhlovskaya structure.We analyzed the graphs of the distribution of indicators in wells R-212 and R-213 in the Akhlovsky area and concluded that the reservoir is heterogeneous, and there are interlayers of mudstones with other reservoir properties and geophysical characteristics. The following pairs of parameters (porosity coefficient and oil-saturated thickness of rocks, rock resistivity and porosity coefficient, rock resistivity and oil-saturated thickness of rocks) have a significant positive correlation. Having studied the distribution of indicators in the Akhlovsky area for wells R-212 and R-213 along one horizon, we concluded that these indicators differ very slightly, which indicates the homogeneity of the reservoir properties. Qualitative indicators Qualitative indicators don't change. Thus, we can expect similar indicators within the entire area of the explored layer Р1+2- К2 in the territory of the Akhlovsky area.


2019 ◽  
Vol 7 (4) ◽  
pp. SH19-SH31
Author(s):  
Gabriela Salomão Martins ◽  
Webster Ueipass Mohriak ◽  
Nivaldo Destro

The Sergipe-Alagoas Basin, situated in the north-east Brazilian margin, has a long tradition of oil and gas production and the presence and distribution of evaporites play an important role in petroleum systems in the basin. However, little research has focused on the structural evolution of the older, synrift evaporitic sections of the basin. We have focused explicitly in the detailed subsurface structural characterization of the rift in the Alagoas subbasin and the distribution of the Early Aptian evaporites. To accomplish this objective, we interpreted selected 2D and 3D seismic and well data located in two areas known as the Varela Low (VL) and Fazenda Guindaste Low (FGL). We identified diverse deformation styles in those two basin depocenters. Our interpretation indicates that VL consists of a half-graben with a significant rollover structure, controlled by two listric northeast–southwest border faults. The deformation in the hanging wall is also accommodated by release faults and minor antithetic faults. In this depocenter, we mapped in the seismic and the well data an older evaporitic sequence within the Coqueiro Seco Fm., known as Horizonte Salt. This evaporitic section occurs in the internal part of the VL half graben, where it is limited by release and antithetic faults. Significant salt strata growing toward the antithetic fault is observed. Whereas, the FGL represents a graben elongated along the north-east direction and is controlled by several types of structures. We recognized normal synthetic and antithetic faults, transfer zones, release faults, and rollover anticlines in the seismic throughout this depocenter. We mapped an evaporitic section within the Maceió Fm., known as Paripueira Salt, which consists of disconnected salt bodies, restricted to the hanging walls of synrift faults.


2012 ◽  
Author(s):  
Amer Badr Merdhah ◽  
Abu Azam Mohd Yassin

Kerak pemendapan merupakan satu daripada masalah paling penting dan serius dalam sistem suntikan air. Kerak kadangkala mengehadkan atau menghalang penghasilan gas dan minyak melalui penyumbatan matrik atau perpecahan pembentukan minyak dan jeda yang berlubang. Makalah ini mengetengahkan kesimpulan pengukuran makmal bagi kerak terbentuk di dalam keterlarutan medan minyak biasa dalam sintetik air masin (pembentukan air dan air laut) bagi pembentukan air yang mengandungi barium dan kandungan garam yang tinggi pada suhu 40 hingga 90°C pada tekanan atmosfera. Keputusan uji kaji mengesahkan pola kebergantungan keterlarutan bagi kerak medan minyak biasa pada keadaan ini. Pada suhu yang lebih tinggi, kerak bagi CaCO3, CaSO4, dan SrSO4 meningkat manakala kerak BaSO4 menurun disebabkan oleh keterlarutan CaCO3, CaSO4, dan SrSO4 menurun dan keterlarutan BaSO4 meningkat dengan kenaikan suhu. Kata kunci: Masalah pengskalaan; skala keterlarutan; paras kandungan garam tinggi; logam barium tinggi Scale deposition is one of the most important and serious problems which water injection systems are generally engaged in. Scale sometimes limits or blocks oil and gas production by plugging the oil–producing formation matrix or fractures and the perforated intervals. This paper presents a summary of the laboratory measurements of the solubility of common oil field scales in synthetic brines (formation water and sea water) of high–barium and high–salinity formation waters at 40 to 90°C and atmospheric pressure. The experimental results confirm the general trend in solubility dependencies for common oil field scales at these conditions. At higher temperatures the deposition of CaCO3, CaSO4 and SrSO4 scale increases and the deposition of BaSO4 scale decreases since the solubilities of CaCO3, CaSO4 and SrSO4 scales decreases and the solubility of BaSO4 increases with increasing temperature. Key words: Scaling problems; solubility of scale; high salinity; high barium


Sign in / Sign up

Export Citation Format

Share Document