Track Fractured Well Inflow Performance Using Historic Production Logging and Surface Well Performance Data in Sultanate of Oman

2022 ◽  
Author(s):  
Cornelis Adrianus Veeken ◽  
Yousuf Busaidi ◽  
Amira Hajri ◽  
Ahmed Mohammed Hegazy ◽  
Hamyar Riyami ◽  
...  

Abstract PDO operates about 200 deep gas wells in the X field in the Sultanate of Oman, producing commingled from the Barik gas-condensate and Miqrat lean gas reservoir completed by multiple hydraulic fracturing. Their inflow performance relation (IPR) is tracked to diagnose condensate damage, hydraulic fracture cleanup and differential reservoir pressure depletion. The best IPR data is collected through multi-rate production logging but surface production data serves as an alternative. This paper describes the process of deriving IPR's from production logging and surface production data, and then evaluates 20 years of historic IPR data to quantify the impact of condensate damage and condensate cleanup with progressive reservoir pressure depletion, to demonstrate the massive damage and slow cleanup of hydraulic fractures placed in depleted reservoirs, to show how hydraulic fractures facilitate the vertical cross-flow between isolated reservoir intervals, and to highlight that stress-dependent permeability does not play a major role in this field.

2021 ◽  
Author(s):  
Behjat Haghshenas ◽  
Farhad Qanbari

Abstract Recovery factor for multi-fractured horizontal wells (MFHWs) at development spacing in tight reservoirs is closely related to the effective horizontal and vertical extents of the hydraulic fractures. Direct measurement of pressure depletion away from the existing producers can be used to estimate the extent of the hydraulic fractures. Monitoring wells equipped with downhole gauges, DFITs from multiple new wells close to an existing (parent) well, and calculation of formation pressure from drilling data are among the methods used for pressure depletion mapping. This study focuses on acquisition of pressure depletion data using multi-well diagnostic fracture injection tests (DFITs), analysis of the results using reservoir simulation, and integration of the results with production data analysis of the parent well using rate-transient analysis (RTA) and reservoir simulation. In this method, DFITs are run on all the new wells close to an existing (parent) well and the data is analyzed to estimate reservoir pressure at each DFIT location. A combination of the DFIT results provides a map of pressure depletion around the existing well, while production data analysis of the parent well provides fracture conductivity and surface area and formation permeability. Furthermore, reservoir simulation is tuned such that it can also match the pressure depletion map by adjusting the system permeability and fracture geometry of the parent well. The workflow of this study was applied to two field case from Montney formation in Western Canadian Sedimentary Basin. In Field Case 1, DFIT results from nine new wells were used to map the pressure depletion away from the toe fracture of a parent well (four wells toeing toward the parent well and five wells in the same direction as the parent). RTA and reservoir simulation are used to analyze the production data of the parent well qualitatively and quantitatively. The reservoir model is then used to match the pressure depletion map and the production data of the parent well and the outputs of the model includes hydraulic fracture half-lengths on both sides of the parent well, formation permeability, fracture surface area and fracture conductivity. In Field Case 2, the production data from an existing well and DFIT result from a new well toeing toward the existing wells were incorporated into a reservoir simulation model. The model outputs include system permeability and fracture surface area. It is recommended to try the method for more cases in a specific reservoir area to get a statistical understanding of the system permeability and fracture geometry for different completion designs. This study provides a practical and cost-effective approach for pressure depletion mapping using multi-well DFITs and the analysis of the resulting data using reservoir simulation and RTA. The study also encourages the practitioners to take every opportunity to run DFITs and gather pressure data from as many well as possible with focus on child wells.


2021 ◽  
Author(s):  
Qin Ji ◽  
Geoff Vernon ◽  
Juan Mata ◽  
Shannon Klier ◽  
Matthew Perry ◽  
...  

Abstract This paper demonstrates how to use pressure data from offset wells to assess fracture growth and evolution through each stage by quantifying the impacts of nearby parent well depletion, completion design, and formation. Production data is analyzed to understand the correlation between fracture geometries, well interactions, and well performance. The dataset in this project includes three child wells and one parent well, landed within two targets of the Wolfcamp B reservoir in the Midland Basin. The following workflow helped the operator understand the completion design effectiveness and its impact to production:Parent well pressure analysis during completionIsolated stage offset pressure analysis during completionOne-month initial production analysis followed by one month shut-inPressure interference test: sequentially bringing wells back onlineProduction data comparison before and after shut-in period An integrated analysis of surface pressure data acquired from parent and offset child wells during completions provides an understanding of how hydraulic dimensions of each fracture stage are affected by fluid volume, proppant amount, frac stage order of operations, and nearby parent well depletion. Production data from all wells was analyzed to determine the impact of depletion on child well performance and to investigate the effects of varying completion designs. A pressure interference test based on Chow Pressure Group was also performed to further examine the connectivity between wells, both inter- and intra-zone. Surface pressure data recorded from isolated stages in the offset child wells during completions was used to resolve geometries and growth rates of the stimulated fractures. Asymmetric fracture growth, which preferentially propagates toward the depleted rock volume around the parent well, was identified at the heel of the child well closest to the parent. Fracture geometries of various child well stage groups were analyzed to determine the effectiveness of different completion designs and the impact of in situ formation properties. Analysis of parent well surface pressure data indicates that changing the completion design effectively reduced the magnitude of Fracture Driven Interactions (FDIs) between child and parent wells. Child well production was negatively impacted in the wells where the fracture boundary overlapped with the parent well depleted volume in the same formation zone. This study combines pressure and production analyses to better understand inter- and intra-zone interference between wells. The demonstrated workflow offers a very cost-effective approach to studying well interference. Observing and understanding the factors that drive fracture growth behavior enables better decision-making during completion design planning, mitigation of parent-child communication, and enhancement of offset well production.


2014 ◽  
Vol 59 (4) ◽  
pp. 987-1004 ◽  
Author(s):  
Łukasz Klimkowski ◽  
Stanisław Nagy

Abstract Multi-stage hydraulic fracturing is the method for unlocking shale gas resources and maximizing horizontal well performance. Modeling the effects of stimulation and fluid flow in a medium with extremely low permeability is significantly different from modeling conventional deposits. Due to the complexity of the subject, a significant number of parameters can affect the production performance. For a better understanding of the specifics of unconventional resources it is necessary to determine the effect of various parameters on the gas production process and identification of parameters of major importance. As a result, it may help in designing more effective way to provide gas resources from shale rocks. Within the framework of this study a sensitivity analysis of the numerical model of shale gas reservoir, built based on the latest solutions used in industrial reservoir simulators, was performed. The impact of different reservoir and hydraulic fractures parameters on a horizontal shale gas well production performance was assessed and key factors were determined.


Author(s):  
Clark Huffman

Abstract The ability to predict well inflow performance for varying well and reservoir conditions is important when optimizing production. Many methods exist to estimate a well’s current productive capacity (IPR curve) and extensions to the methods are available for predicting future well performance. The extensions to predict future inflow performance behavior account for changes in relative permeability and assume an average reservoir pressure. The applicability and accuracy of the methods depends on knowledge of reservoir parameters which may be difficult to obtain in low permeability reservoirs. Several authors have presented methods of analyzing and history matching well performance. These methods typically yield reservoir parameters which may be used in the well inflow performance methods in order to investigate the results of varying well production parameters. These methods are particularly useful in low permeability settings where interpretable welltest data may be difficult to obtain or prohibitively expensive. Currently, the analytical history matching approach is most accurate when applied to single-phase systems. Predictions of black oil reservoir performance below the bubble point can exhibit large error since depletion of the total reservoir energy is not accounted for using the constant gas-oil ratio approach typical for these methods. This paper presents a method to analyze well performance of black oil systems below the bubble point. The method incorporates a material balance approach to account for changing gas-oil ratios as the reservoir is depleted. Prediction of future well performance is also presented. Along with reservoir characterization, another benefit of the method is the ability to construct IPR curves at any point in order to optimize production. The proposed method uses a pseudo pressure transform to account for changes in fluid properties as the reservoir pressure is depleted. Relative permeability changes can be incorporated in the pseudo pressure transform. Comparisons to finite difference simulation results and actual productio data are presented. Comparisons of future IPR curves generated by other methods are also presented.


2015 ◽  
Author(s):  
Karthik Srinivasan ◽  
Midowa Gbededo ◽  
Hongxue Hue ◽  
Jayanth Krishnamurthy ◽  
Veronica Gonzales

Abstract Evaluating the effects of asymmetric stress distribution around a lateral can greatly help optimize completion techniques and overall production from in-fill horizontal wells in unconventional shale and tight reservoirs. Several factors affect long-term production from in-fill drilled wells including but not limited to pressure depletion from produced wells, change of effective stresses in the depleted formation and interference between hydraulic fractures when the new in-fill wells are drilled, stimulated and brought into production. The study addresses a variety of key challenges that the unconventional oil and gas industry is looking to understand. These include understanding: How the presence of a depleted wellbore affects hydraulic fracture propagation from a nearby newly drilled wellHow refracturing considerations in a producing well are affected by hydrocarbon drainage and modified stress contrastsHow fracturing/refracturing pumping designs and volumes should be optimized to address the challenges surrounding the wellbore Under circumstances mentioned above, pressure distribution around the wellbore from hydrocarbon drainage was estimated by history matching production data over a certain period of time. Then the impact of various types of fracturing treatments on pressure depletion profiles from offset wells was studied using a fully numerical fracture simulator that is capable of handling asymmetric stress distribution around the lateral. Fracture geometries from this study were either asymmetric due to depletion on only one side of the lateral or longer due to increased stress contrast. These fracture geometries were fed to a production model to forecast long-term production from in-fill wells and study drainage patterns over time. Understanding these challenges provided a sub-surface perspective of how completion techniques should be optimized to get maximum hydrocarbon recovery from reservoirs consisting of laterals that have already been on production.


2002 ◽  
Vol 124 (3) ◽  
pp. 163-172 ◽  
Author(s):  
Turhan Yildiz

This study presents a simplified method to predict inflow performance of and cumulative production from selectively perforated wells in bounded reservoirs. The model first calculates the pseudo-skin for a fully perforated well penetrating a formation with only unit thickness. Then, perforation pseudo-skin is superimposed on a two-dimensional selectively open completed well model. Using the new model, a sensitivity study is carried out to identify the parameters controlling the well flow rate and total recovery. The sensitivity study includes the impact of shot density, perforation size and length, phasing angle, perforated length/formation thickness ratio, and the degree of formation damage around the wellbore and perforations.


2020 ◽  
Vol 15 (2) ◽  
pp. 95-109
Author(s):  
Heba Aziz ◽  
Osman El-Said ◽  
Marike Bontenbal

The objective of this study was to measure the level of cruise tourists' satisfaction as well as the relationship between satisfaction, recommendation, return intention, and expenditure. Also, the impact of factors such as nationality, length of the visit, and age on the level of expenditure was measured. An empirical approach for data collection was followed and a total of 152 questionnaires were collected from cruise tourists visiting the capital city of Oman, Muscat, as cruise liners anchor at Sultan Qaboos Port. Results of the regression analysis supported the existence of a causal relationship between satisfaction with destination attributes, overall satisfaction, recommendation, return intention, and expenditure. It was found that the average expenditure varies according to age and length of the visit. Recommendations for policy makers were suggested on how to increase the role of cruise tourism in strengthening the economy.


2021 ◽  
Vol 2021 (4) ◽  
Author(s):  
A. Andronic ◽  
J. Honermann ◽  
M. Klasen ◽  
C. Klein-Bösing ◽  
J. Salomon

Abstract In this paper we present a study of in-medium jet modifications performed with JEWEL and PYTHIA 6.4, focusing on the uncertainties related to variations of the perturbative scales and nuclear parton distribution functions (PDFs) and on the impact of the initial and crossover temperature variations of the medium. The simulations are compared to LHC data for the jet spectrum and the nuclear modification factor. We assess the interplay between the choice of nuclear PDFs and different medium parameters and study the impact of nuclear PDFs and the medium on the jet structure via the Lund plane.


Energies ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3366
Author(s):  
Daniel Suchet ◽  
Adrien Jeantet ◽  
Thomas Elghozi ◽  
Zacharie Jehl

The lack of a systematic definition of intermittency in the power sector blurs the use of this term in the public debate: the same power source can be described as stable or intermittent, depending on the standpoint of the authors. This work tackles a quantitative definition of intermittency adapted to the power sector, linked to the nature of the source, and not to the current state of the energy mix or the production predictive capacity. A quantitative indicator is devised, discussed and graphically depicted. A case study is illustrated by the analysis of the 2018 production data in France and then developed further to evaluate the impact of two methods often considered to reduce intermittency: aggregation and complementarity between wind and solar productions.


2021 ◽  
Author(s):  
Rohan Sakhardande ◽  
Deepak Devegowda

Abstract The analyses of parent-child well performance is a complex problem depending on the interplay between timing, completion design, formation properties, direct frac-hits and well spacing. Assessing the impact of well spacing on parent or child well performance is therefore challenging. A naïve approach that is purely observational does not control for completion design or formation properties and can compromise well spacing decisions and economics and perhaps, lead to non-intuitive results. By using concepts from causal inference in randomized clinical trials, we quantify the impact of well spacing decisions on parent and child well performance. The fundamental concept behind causal inference is that causality facilitates prediction; but being able to predict does not imply causality because of association between the variables. In this study, we work with a large dataset of over 3000 wells in a large oil-bearing province in Texas. The dataset includes several covariates such as completion design (proppant/fluid volumes, frac-stages, lateral length, cluster spacing, clusters/stage and others) and formation properties (mechanical and petrophysical properties) as well as downhole location. We evaluate the impact of well spacing on 6-month and 1-year cumulative oil in four groups associated with different ranges of parent-child spacing. By assessing the statistical balance between the covariates for both parent and child well groups (controlling for completion and formation properties), we estimate the causal impact of well spacing on parent and child well performance. We compare our analyses with the routine naïve approach that gives non-intuitive results. In each of the four groups associated with different ranges of parent-child well spacing, the causal workflow quantifies the production loss associated with the parent and child well. This degradation in performance is seen to decrease with increasing well spacing and we provide an optimal well spacing value for this specific multi-bench unconventional play that has been validated in the field. The naïve analyses based on simply assessing association or correlation, on the contrary, shows increasing child well degradation for increasing well spacing, which is simply not supported by the data. The routinely applied correlative analyses between the outcome (cumulative oil) and predictors (well spacing) fails simply because it does not control for variations in completion design over the years, nor does it account for variations in the formation properties. To our knowledge, there is no other paper in petroleum engineering literature that speaks of causal inference. This is a fundamental precept in medicine to assess drug efficacy by controlling for age, sex, habits and other covariates. The same workflow can easily be generalized to assess well spacing decisions and parent-child well performance across multi-generational completion designs and spatially variant formation properties.


Sign in / Sign up

Export Citation Format

Share Document