Non-Edible Oil Based Surfactant For Enhanced Oil Recovery

2021 ◽  
Author(s):  
Adekunle Tirimisiyu Adeniyi ◽  
Ijoma Onyemaechi
Keyword(s):  
Methyl Ester ◽  
Sodium Hydroxide ◽  
Sodium Carbonate ◽  
Oil Recovery ◽  
Sodium Dodecyl ◽  
Synthetic Surfactant ◽  
Chemical Flooding ◽  
Core Flooding ◽  
Incremental Oil Recovery ◽  
Increasing Demand

Abstract After the primary and secondary oil recoveries, a substantial amount of oil is left in the reservoir which can be recovered by tertiary methods like the Alkaline-Surfactant Flood. Reasons for having some unproduced hydrocarbon in the reservoir include and not limited to the following; forces of attraction fluid contacts, low permeability, high viscous fluid, poor swept efficiency, etc. Although, it is possible to commence waterflooding together chemical injection at the start of production. Reservoir simulation with commercial simulator, could guide in selecting the most appropriate period to commence chemical flooding. In this study, the performance of a new synthetic surfactant produced from Jatropha Curcas seed was compared with that of a selected commercial surfactant in the presence of an alkaline and this shows that the non-edible Jatropha oil is a natural, inexpensive and a renewable source of energy for the production of anionic surfactants and a good substitute for commercial surfactants like Sodium Dodecyl Sulphate (SDS). The Methyl Ester Sulfonate (MES) surfactant showed no precipitation or cloudiness during stability test and was able to reduce the Interfacial Tension (IFT) to 0.018 mN/m and 0.020 mN/m in the presence of sodium carbonate and sodium hydroxide respectively as alkaline at low surfactant concentration. The optimum alkaline surfactant formulation in terms of oil recovery performance obtained from the core flooding experiment corresponds to a concentration of sodium carbonate (0.5wt%), sodium hydroxide (0.5wt%) mixed in distilled water and Methyl Ester Sulfonate (MES) surfactant (1wt%). The injection of 0.5 percentage volume of alkaline surfactant slug produced an incremental oil recovery of 26.7% and 29% respectively. With these incremental oil recoveries, increasing demand for hydrocarbons product could be met, and returns on investment portfolio will be improved.

scholarly journals Experimental Investigation of Chemical Flooding Using Nanoparticles and Polymer on Displacement of Crude Oil for Enhanced Oil Recovery

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Imran Akbar ◽  
Hongtao Zhou ◽  
Wei Liu ◽  
Muhammad Usman Tahir ◽  
Asadullah Memon ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Petroleum Industry ◽  
Chemical Flooding ◽  
Polymer Gel ◽  
Core Flooding ◽  
High Concentration ◽  
Remaining Oil ◽  
Water Cut

In the petroleum industry, the researchers have developed a new technique called enhanced oil recovery to recover the remaining oil in reservoirs. Some reservoirs are very complex and require advanced enhanced oil recovery (EOR) techniques containing new materials and additives in order to produce maximum oil in economic and environmental friendly manners. In this work, the effects of nanosuspensions (KY-200) and polymer gel HPAM (854) on oil recovery and water cut were studied in the view of EOR techniques and their results were compared. The mechanism of nanosuspensions transportation through the sand pack was also discussed. The adopted methodology involved the preparation of gel, viscosity test, and core flooding experiments. The optimum concentration of nanosuspensions after viscosity tests was used for displacement experiments and 3 wt % concentration of nanosuspensions amplified the oil recovery. In addition, high concentration leads to more agglomeration; thus, high core plugging takes place and diverts the fluid flow towards unswept zones to push more oil to produce and decrease the water cut. Experimental results indicate that nanosuspensions have the ability to plug the thief zones of water channeling and can divert the fluid flow towards unswept zones to recover the remaining oil from the reservoir excessively rather than the normal polymer gel flooding. The injection pressure was observed higher during nanosuspension injection than polymer gel injection. The oil recovery was achieved by about 41.04% from nanosuspensions, that is, 14.09% higher than polymer gel. Further investigations are required in the field of nanoparticles applications in enhanced oil recovery to meet the world's energy demands.

A Modified HLD-NAC Equation of State To Predict Alkali/Surfactant/Oil/Brine Phase Behavior

SPE Journal ◽  
2018 ◽  
Vol 23 (02) ◽  
pp. 550-566 ◽  
Author(s):  
Soumyadeep Ghosh ◽  
Russell T. Johns
Keyword(s):  
Equation Of State ◽  
Phase Behavior ◽  
Oil Recovery ◽  
Naphthenic Acids ◽  
Phase Region ◽  
Measured Data ◽  
Synthetic Surfactant ◽  
Chemical Flooding ◽  
Mineral Surfaces ◽  
Dimensionless Equation

Summary Reservoir crudes often contain acidic components (primarily naphthenic acids), which undergo neutralization to form soaps in the presence of alkali. The generated soaps perform synergistically with injected synthetic surfactants to mobilize waterflood residual oil in what is termed alkali/surfactant/polymer (ASP) flooding. The two main advantages of using alkali in enhanced oil recovery (EOR) are to lower cost by injecting a lesser amount of expensive synthetic surfactant and to reduce adsorption of the surfactant on the mineral surfaces. The addition of alkali, however, complicates the measurement and prediction of the microemulsion phase behavior that forms with acidic crudes. For a robust chemical-flood design, a comprehensive understanding of the microemulsion phase behavior in such processes is critical. Chemical-flooding simulators currently use Hand's method to fit a limited amount of measured data, but that approach likely does not adequately predict the phase behavior outside the range of the measured data. In this paper, we present a novel and practical alternative. In this paper, we extend a dimensionless equation of state (EOS) (Ghosh and Johns 2016b) to model ASP phase behavior for potential use in reservoir simulators. We use an empirical equation to calculate the acid-distribution coefficient from the molecular structure of the soap. Key phase-behavior parameters such as optimum salinities and optimum solubilization ratios are calculated from soap-mole-fraction-weighted equations. The model is tuned to data from phase-behavior experiments with real crudes to demonstrate the procedure. We also examine the ability of the new model to predict fish plots and activity charts that show the evolution of the three-phase region. The predictions of the model are in good agreement with measured data.

scholarly journals Synthesis and Characterization of Polymeric Surfactant from Palm Oil Methyl Ester and Vinyl Acetate for Chemical Flooding

REAKTOR ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 65-73
Author(s):  
Agam Duma Kalista Wibowo ◽  
Pina Tiani ◽  
Lisa Aditya ◽  
Aniek Sri Handayani ◽  
Marcelinus Christwardana
Keyword(s):  
Methyl Ester ◽  
Interfacial Tension ◽  
Vinyl Acetate ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Mobility Control ◽  
Wettability Alteration ◽  
Polymeric Surfactant ◽  
Chemical Flooding

Surfactants for enhanced oil recovery are generally made from non-renewable petroleum sulfonates and their prices are relatively expensive, so it is necessary to synthesis the bio-based surfactants that are renewable and ecofriendly. The surfactant solution can reduce the interfacial tension (IFT) between oil and water while vinyl acetate monomer has an ability to increase the viscosity as a mobility control. Therefore, polymeric surfactant has both combination properties in reducing the oil/water IFT and increasing the viscosity of the aqueous solution simultaneously. Based on the study, the Critical Micelle Concentration (CMC) of Polymeric Surfactant was at 0.5% concentration with an IFT of 7.72x10-2 mN/m. The best mole ratio of methyl ester sulfonate to vinyl acetate for polymeric surfactant synthesis was 1:0.5 with an IFT of 6.7x10-3 mN/m. Characterization of the product using FTIR and HNMR has proven the creation of polymeric surfactant. Based on the wettability alteration study, it confirmed that the product has an ability to alter from the initial oil-wet to water-wet quartz surface. In conclusion, the polymeric surfactant has ultralow IFT and could be an alternative surfactant for chemical flooding because the IFT value met with the required standard for chemical flooding ranges from 10-2 to 10-3 mN/m.Keywords: Enhanced Oil recovery, Interfacial Tension, Methyl Ester Sulfonate, Polymeric surfactant, vinyl acetate

scholarly journals MICROEMULSION FLOODING MECHANISM FOR OPTIMUM OIL RECOVERY ON CHEMICAL INJECTION

2018 ◽  
Vol 40 (2) ◽  
pp. 85-90
Author(s):  
Yani Faozani Alli ◽  
Edward ML Tobing ◽  
Usman Usman
Keyword(s):  
Oil Recovery ◽  
Mobility Control ◽  
Chemical Flooding ◽  
Residual Oil ◽  
Core Flooding ◽  
Oil Viscosity ◽  
Oil Saturation ◽  
Remaining Oil ◽  
Tertiary Oil Recovery

The formation of microemulsion in the injection of surfactant at chemical flooding is crucial for the effectiveness of injection. Microemulsion can be obtained either by mixing the surfactant and oil at the surface or injecting surfactant into the reservoir to form in situ microemulsion. Its translucent homogeneous mixtures of oil and water in the presence of surfactant is believed to displace the remaining oil in the reservoir. Previously, we showed the effect of microemulsion-based surfactant formulation to reduce the interfacial tension (IFT) of oil and water to the ultralow level that suffi cient enough to overcome the capillary pressure in the pore throat and mobilize the residual oil. However, the effectiveness of microemulsion flooding to enhance the oil recovery in the targeted representative core has not been investigated.In this article, the performance of microemulsion-based surfactant formulation to improve the oil recovery in the reservoir condition was investigated in the laboratory scale through the core flooding experiment. Microemulsion-based formulation consist of 2% surfactant A and 0.85% of alkaline sodium carbonate (Na2CO3) were prepared by mixing with synthetic soften brine (SSB) in the presence of various concentration of polymer for improving the mobility control. The viscosity of surfactant-polymer in the presence of alkaline (ASP) and polymer drive that used for chemical injection slug were measured. The tertiary oil recovery experiment was carried out using core flooding apparatus to study the ability of microemulsion-based formulation to recover the oil production. The results showed that polymer at 2200 ppm in the ASP mixtures can generate 12.16 cP solution which is twice higher than the oil viscosity to prevent the fi ngering occurrence. Whereas single polymer drive at 1300 ppm was able to produce 15.15 cP polymer solution due to the absence of alkaline. Core flooding experiment result with design injection of 0.15 PV ASP followed by 1.5 PV polymer showed that the additional oil recovery after waterflood can be obtained as high as 93.41% of remaining oil saturation after waterflood (Sor), or 57.71% of initial oil saturation (Soi). Those results conclude that the microemulsion-based surfactant flooding is the most effective mechanism to achieve the optimum oil recovery in the targeted reservoir.

Analyzing the Influence of Salinity on Produced Water Re-Injection

2021 ◽  
Author(s):  
Adekunle Tirimisiyu Adeniyi ◽  
Chimgozirim Prince Ejim
Keyword(s):  
Oil Recovery ◽  
Produced Water ◽  
Core Sample ◽  
Production Performance ◽  
Core Flooding ◽  
Daily Rate ◽  
Reservoir Conditions ◽  
Cumulative Production ◽  
Water Disposal ◽  
Incremental Oil Recovery

Abstract Produced water reinjection (PWRI) is one of the methods employed by oilfield operators to optimize production while conforming to increasingly stringent produced water disposal policies. Different produced water species from different facilities also have different salinities as a result of entrainment of treatment fluids, precipitation of salts at surface conditions, etc. During re-injection operations, the salinity of the injection fluid has to be accounted for as it affects the production. Previous studies have focused on laboratory analysis by core flooding. While this approach is indeed reasonable and offers a first-hand impression of the reservoir conditions, it presents a problem of cost and the age-old opinion that the core sample may not be representative of the entire reservoir. Therefore, I have employed a computer modeling approach using a commercial simulator to analyze the influence of salinity on production during produced water re-injection. It was found that the salinity truly affects production. Re-injection of produced water with salinity equal to the reservoir salinity of 1000 ppm was compared to three cases of re-injection of produced water from extraneous sources having salinities of 100 ppm, 500 ppm and 10000 ppm. It was found that salinity of 10000 ppm gave the best oil production performance for the reservoir model; a daily rate of 40 STB/DAY and an oil cumulative production of 40,000 STB. Incremental salinity of injected produced water led to incremental oil recovery. The mechanism resulting in incremental recovery was attributed to the increase in viscosity and decrease in mobility as the salinity increases.

Alkaline/Surfactant/Polymer Chemical Flooding Without the Need for Soft Water

SPE Journal ◽  
2009 ◽  
Vol 15 (01) ◽  
pp. 184-196 ◽  
Author(s):  
Adam K. Flaaten ◽  
Quoc P Nguyen ◽  
Jieyuan Zhang ◽  
Hourshad Mohammadi ◽  
Gary A. Pope
Keyword(s):  
Sodium Carbonate ◽  
Oil Recovery ◽  
High Performance ◽  
High Salinity ◽  
Divalent Cations ◽  
Low Cost ◽  
Soft Water ◽  
Chemical Flooding ◽  
Asp Flooding ◽  
Alkaline Surfactant Polymer

Summary Alkaline/surfactant/polymer (ASP) flooding using conventional alkali requires soft water. However, soft water is not always available, and softening hard brines may be very costly or infeasible in many cases depending on the location, the brine composition, and other factors. For instance, conventional ASP uses sodium carbonate to reduce the adsorption of the surfactant and generate soap in-situ by reacting with acidic crude oils; however, calcium carbonate precipitates unless the brine is soft. A form of borax known as metaborate has been found to sequester divalent cations such as Ca++ and prevent precipitation. This approach has been combined with the screening and selection of surfactant formulations that will perform well with brines having high salinity and hardness. We demonstrate this approach by combining high-performance, low-cost surfactants with cosurfactants that tolerate high salinity and hardness and with metaborate that can tolerate hardness as well. Chemical formulations containing surfactants and alkali in hard brine were screened for performance and tolerance using microemulsion phase-behavior experiments and crude at reservoir temperature. A formulation was found that, with an optimum salinity of 120,000 ppm total dissolved solids (TDS), 6,600 ppm divalent cations, performed well in corefloods with high oil recovery and almost zero final chemical flood residual oil saturation. Additionally, chemical formulations containing sodium metaborate and hard brine gave nearly 100% oil recovery with no indication of precipitate formation. Metaborate chemistry was incorporated into a mechanistic, compositional chemical flooding simulator, and the simulator was then used to model the corefloods. Overall, novel ASP with metaborate performed comparably to conventional ASP using sodium carbonate in soft water, demonstrating advancements in ASP adaptation to hard, saline reservoirs without the need for soft brine, which increases the number of oil reservoirs that are candidates for enhanced oil recovery using ASP flooding.

Evaluation and Application of Endogenous Microorganism Activator in Reservoir after Chemical Flooding

2014 ◽  
Vol 1051 ◽  
pp. 404-409
Author(s):  
Jian Jun Le ◽  
Ji Yuan Zhang ◽  
Lu Lu Bai ◽  
Rui Wang ◽  
Zhao Wei Hou ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
High Pressure ◽  
Oil Recovery ◽  
Physical Simulation ◽  
Chemical Flooding ◽  
Core Flooding ◽  
Simulation Experiments ◽  
The Core ◽  
Enhance Oil Recovery ◽  
Growth And Reproduction

To further enhance oil recovery in reservoir after chemical flooding, an efficient activator formulation for promoting metabolism of endogenous microorganism was researched. Changes in community structure, growth and metabolites of endogenous microorganism were analyzed by methods of aerogenic experiments, physical simulation experiments, electron microscopy scanning (SEM), T-RFLP and Pyrophosphate sequencing. To evaluate whether endogenous microorganism activator screened in laboratory could activate endogenous microorganisms and enhance oil recovery in reservoirs after polymer flooding. The flooding effect and mechanism were studied, and this activator was used in a testing well group in Daqing oilfield. The results of the aerogenic experiments showed that the activator could activate the endogenous microorganisms in the injected water and make them produce a lot of biogas. The pressurized gas reached 2MPa after 60d static culture of activator in a high pressure vessel. The results showed that the activator could activate the endogenous microorganisms in the injected sewage and make them have a lot of growth and reproduction in the core and physical simulation of natural core flooding experiment. In the field test,the incremental oil production was 5957 t while the water content declined by 2.2% after injecting the activator, which provides an effective way to further enhance oil recovery in reservoir after chemical flooding.

scholarly journals Characterization and oil recovery enhancement by a polymeric nanogel combined with surfactant for sandstone reservoirs

2020 ◽  
Author(s):  
Mustafa Almahfood ◽  
Baojun Bai
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Suspension Polymerization ◽  
Sodium Dodecyl ◽  
Polymerization Process ◽  
Core Flooding ◽  
A Value ◽  
Fixed Concentration ◽  
Oil In Water ◽  
Recovery Mechanisms

Abstract The characterization and enhanced oil recovery mechanisms of a nanosized polymeric cross-linked gel are presented herein. A negatively charged nanogel was synthesized using a typical free radical suspension polymerization process by employing 2-acrylamido 2-methyl propane sulfonic acid monomer. The synthesized nanogel showed a narrow size distribution with one peak pointing to a predominant homogeneous droplet size. The charged nanogels were also able to adsorb at the oil–water interfaces to reduce interfacial tension and stabilize oil-in-water emulsions, which ultimately improved the recovered oil from hydrocarbon reservoirs. In addition, a fixed concentration of negatively charged surfactant (sodium dodecyl sulfate or SDS) was combined with different concentrations of the nanogel. The effect of the nanogels combined with surfactant on sandstone core plugs was examined by running a series of core flooding experiments using multiple flow patterns. The results show that combining nanogel and SDS was able to reduce the interfacial tension to a value of 6 Nm/m. The core flooding experiments suggest the ability of the nanogel, both alone and combined with SDS, to improve the oil recovery by a factor of 15% after initial seawater flooding.

scholarly journals Numerical Simulation and Optimization of Enhanced Oil Recovery by the In Situ Generated CO2Huff-n-Puff Process with Compound Surfactant

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Yong Tang ◽  
Zhengyuan Su ◽  
Jibo He ◽  
Fulin Yang
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
History Matching ◽  
Injection Rate ◽  
Thermal Recovery ◽  
Chemical Flooding ◽  
Core Flooding ◽  
Daily Production ◽  
Simulation And Optimization

This paper presents the numerical investigation and optimization of the operating parameters of the in situ generated CO2Huff-n-Puff method with compound surfactant on the performance of enhanced oil recovery. First, we conducted experiments of in situ generated CO2and surfactant flooding. Next, we constructed a single-well radial 3D numerical model using a thermal recovery chemical flooding simulator to simulate the process of CO2Huff-n-Puff. The activation energy and reaction enthalpy were calculated based on the reaction kinetics and thermodynamic models. The interpolation parameters were determined through history matching a series of surfactant core flooding results with the simulation model. The effect of compound surfactant on the Huff-n-Puff CO2process was demonstrated via a series of sensitivity studies to quantify the effects of a number of operation parameters including the injection volume and mole concentration of the reagent, the injection rate, the well shut-in time, and the oil withdrawal rate. Based on the daily production rate during the period of Huff-n-Puff, a desirable agreement was shown between the field applications and simulated results.

Sign in / Sign up

Export Citation Format

Share Document