scholarly journals Experience in Wales (UK) of the optimisation of ortho-phosphate dosing for controlling lead in drinking water

2008 ◽  
Vol 6 (2) ◽  
pp. 177-185 ◽  
Author(s):  
C. R. Hayes ◽  
S. Incledion ◽  
M. Balch
Keyword(s):  
Drinking Water ◽  
Successful Outcome ◽  
Water Supplies ◽  
Ph Adjustment ◽  
Lead Pipe ◽  
The Future ◽  
Water Mains ◽  
Lead Pipes ◽  
Dose Control ◽  
Selection Of

Dwr Cymru Welsh Water supplies over three million people with drinking water throughout most of Wales (UK). Ortho-phosphate has increasingly been dosed at around 1 mg/L (P) to further reduce the corrosivity of supplies to the lead pipes which connect approximately 30% of houses to water mains in the company's area, additional to long-establish pH adjustment measures. The installation of new ortho-phosphate dosing schemes and the optimisation of these and existing dosing schemes, 29 schemes in total, were subject to a regulatory programme of work, agreed with the Drinking Water Inspectorate (DWI). Optimisation comprised (i) selection of appropriate ortho-phosphate doses by a procedure involving laboratory based plumbosolvency testing linked to zonal lead emission (compliance) modelling, (ii) tight dose control and (iii) extensive monitoring of lead in supply by random daytime (RDT) sampling and by the use of lead pipe test rigs. The successful outcome was confirmed by 99% of over 5,000 RDT samples complying with the future standard of 10 μg/L for lead in drinking water.

scholarly journals Coping with poor water supplies: empirical evidence from Kathmandu, Nepal

2011 ◽  
Vol 9 (1) ◽  
pp. 143-158 ◽  
Author(s):  
Hari Katuwal ◽  
Alok K. Bohara
Keyword(s):  
Drinking Water ◽  
Drinking Water Treatment ◽  
Poor Quality ◽  
Water Supplies ◽  
Point Of Use ◽  
Quality Of Water ◽  
Major Treatment ◽  
Clean Drinking Water ◽  
Selection Of

The authors examined the demand for clean drinking water using treatment behaviors in Kathmandu, Nepal. Water supply is inadequate, unreliable and low quality. Households engage in several strategies to cope with the unreliable and poor quality of water supplies. Some of the major coping strategies are hauling, storing, and point-of-use treatment. Boiling, filtering, and use of Uro-guard are some of the major treatment methods. Using Water Survey of Kathmandu, the authors estimated the effect of wealth, education, information, gender, caste/ethnicity and opinion about water quality on drinking water treatment behaviors. The results show that people tend to increase boiling and then filtering instead of only one method if they are wealthier. In addition, people boil and then filter instead of boiling only and filtering only if they think that water delivered to the tap is dirty. Exposure to information has the strongest effect in general for the selection of all available treatment modes.

STAGES OF HIGHER MATHEMATICS TEACHING FOR FUTURE CIVIL PROTECTION SPECIALISTS

2018 ◽  
pp. 168-172
Author(s):  
M. Kusiy
Keyword(s):  
Information Search ◽  
Cognitive Activity ◽  
Civil Defense ◽  
Educational Material ◽  
Material System ◽  
Civil Protection ◽  
Intellectual Activity ◽  
Innovative Teaching ◽  
The Future ◽  
Selection Of

Introduction.  During the training of emergency specialists, the development of a clear, structured thinking is important.  And the mathematical disciplines themselves are aimed at activating the intellectual activity of cadets and students, the ability to think logically, consistently, and reasonably.  However, cadets and students consider mathematics to be a complex, inaccessible and not very necessary science.  Therefore, there is a need for continuous, continuous development of methods, technologies of forms of training that would increase interest, accessibility to mathematical disciplines and at the same time, were aimed at improving the quality of training of future rescuers. Purpose.  Identify the main stages of teaching higher mathematics for future civil defense specialists and substantiate their peculiarities. Methods.  The article used methods of scientific knowledge (general), methods used in the empirical and theoretical levels of research (transition from abstract to specific).  Results.  The basic stages of teaching higher mathematics for future specialists of civil defense are determined: motivation, research, assimilation, application.  The proposed stages are analyzed in detail.  The regularities that contribute to the increase of motivation (selection of educational material, system approach, creative approach, a variety of forms and methods of teaching, taking into account the specifics of the future profession, the use of innovative teaching technologies) are highlighted.  There are three phases of knowledge (curiosity, curiosity, theoretical knowledge).  It is determined that for the acquisition of knowledge it is possible to use the information - search type of classes with its microstructure.  Planning the microstructure of occupations in the first place should put the level of cognitive activity, awareness and independence in the performance of educational tasks.  It is noted that the process of assimilation is the process of internalization of knowledge, putting it into the inner plan of man, and the application is to extraorise knowledge, make it to the outline of human activity.  It was investigated that the stage of application of knowledge is divided into two parts (the first is the application of knowledge, skills in standard terms, the second - the transfer of knowledge, skills, skills in new, changed conditions).  Examples of applied tasks that can be solved in higher mathematics classes are given.  It is substantiated that only in combination of all stages is formed the need for knowledge acquisition and their application. Conclusion.  Stages of teaching higher mathematics - a cyclical process that requires constant improvement, hard work of the teacher.  Stages of motivation and application combine the same laws (selection of educational material, creative approach, taking into account the specifics of the future profession, the use of innovative teaching technologies).  And only in a logical, thought-out combination of these stages can one form the future need for civil protection specialists to expand the knowledge and apply it to practical application.

Цифровая морфометрия разнокачественности семян овощных культур

2018 ◽  
Author(s):  
F.B. Musaev ◽  
N.S. Priyatkin ◽  
M.V. Arkhipov ◽  
P.A. Shchukina ◽  
A.F. Bukharov ◽  
...  
Keyword(s):  
Seed Quality ◽  
Image Analysis System ◽  
Flatbed Scanner ◽  
The Future ◽  
Scanned Images ◽  
Computer Morphometry ◽  
Analysis System ◽  
Matrix Heterogeneity ◽  
Relationship Of ◽  
Selection Of

Приведено описание разработанной авторами методики цифровой компьютерной морфометрии семян овощных культур на основе системы анализа изображений, состоящей из планшетного сканера и программного обеспечения для автоматических измерений. В основу метода положено представление о разнокачественности семян, обусловленной генетической неоднородностью самих семенных растений, используемых в промышленном семеноводстве. Физические свойства семян (их форма и линейные размеры) – основные параметры при определении их качества. Цифровые изображения семян получены при помощи планшетного сканера HP Sсanjet 200 на базе Агрофизического НИИ с использованием серийного программного обеспечения «Argus-BIO», производства ООО «АргусСофт» (г. Санкт-Петербург). Метод состоит из подбора контрастной подложки (фона) для сканирования семян с минимальными теневыми эффектами, калибровку программного обеспечения для привязки к истинным размерным величинам, подбор параметров измерений и автоматическое распознавание цифровых сканированных изображений семян. Представлены экспериментальные данные по морфометрии экологически разнокачественных семян фасоли овощной, матрикально разнокачественных семян укропа, пастернака и лука Кристофа. Семена укропа и пастернака, собранные из разных порядков ветвления семенного растения, значительно различались по величине линейных параметров. Наиболее показательный линейный параметр семян – площадь проекции. Предложенная авторами методика цифровой морфометрии, уже использована на практике и в перспективе может быть задействована в исследованиях экологической и матрикальной разнокачественности семян овощных культур. Так, она прошла апробацию на разнокачественных семенах пяти сортов фасоли овощной (Настена, Магура, Миробела, Морена, Бажена) полученных в пяти контрастных эколого-географических условиях среды (Москва, Белгород, Ставрополь, Омск, Горки) в 2011–2012 годах. В дальнейшем методика может быть использована для улучшения качества цифровых изображений семян, изучения разнокачественности семян в том числе и для совершенствования контроля за селекционным процессом. Кроме того, она применима для изучения взаимосвязи совокупности морфометрических характеристик семян и их посевных качеств.The description of the method of digital computer morphometry of vegetable seeds developed by the authors on the basis of the image analysis system consisting of a flatbed scanner and software for automatic measurements is given. The method is based on the idea of seed quality, due to the genetic heterogeneity of the seed plants used in industrial seed production. Physical properties of seeds (their shape and linear dimensions) are the main parameters in determining their quality. Digital image of the seed obtained using the flatbed scanner, HP Sсanjet 200 on the basis of the Agrophysical research Institute with serial software “Argus-BIO”, produced by LLC “Argussoft” (Saint-Petersburg). The method consists of selection of a contrast substrate (background) for scanning seeds with minimal shadow effects, calibration of software for binding to true size values, selection of measurement parameters and automatic recognition of digital scanned images of seeds. Experimental data on the morphometry of ecologically different-quality seeds of vegetable beans, matrix seeds of dill, Pasternak and Christoph onion are presented. Seeds of dill and parsnip, collected from different orders of branching of the seed plant, significantly differed in size of linear parameters. The most revealing linear parameter seed – area projection. The method of digital morphometry proposed by the authors has already been used in practice and in the future can be used in studies of ecological and matrix heterogeneity of vegetable seeds. So, it was tested on different quality seeds of five varieties of vegetable beans (Nastena, Magura, Mirobelа, Morena, Bazhenf) obtained in five contrasting environmental and geographical conditions (Moscow, Belgorod, Stavropol, Omsk, Gorki) in 2011-2012. In the future, the technique can be used to improve the quality of digital images of seeds, study of seed diversity, including to improve the control of the breeding process. In addition, it is applicable to study the relationship of the set of morphometric characteristics of seeds and their sowing qualities.

MODELLING CHLORINE DECAY IN DRINKING WATER MAINS

2008 ◽  
Vol 7 (6) ◽  
pp. 737-741 ◽  
Author(s):  
Diana Robescu ◽  
Nicolae Jivan ◽  
Dan Robescu
Keyword(s):  
Drinking Water ◽  
Water Mains ◽  
Chlorine Decay

MODERN CONDITION AND PROSPECTS OF DEVELOPMENT OF THE UKRAINIAN WHITEHEAD BREED

2016 ◽  
Vol 52 ◽  
pp. 194-202
Author(s):  
S. L. Voitenko ◽  
L. V. Vishnevsky
Keyword(s):  
Milk Yield ◽  
Milk Fat ◽  
Objective Assessment ◽  
Live Weight ◽  
Fat Content ◽  
Early Age ◽  
Average Value ◽  
The Future ◽  
Efficiency Of Selection ◽  
Selection Of

The article shows the state of Ukrainian Whiteheaded cattle, which includes distribution of cattle, the number of animals belonging to respective bloodlines, evaluation of young animals with live weight in the process of growing and milk production of cows during the first lactation. It reflects the historic development of the breed when it was colonism whiteheaded cattle, which turned into the original breed, undergone a significant expansion in livestock and increase of productivity, decreased in the number, was as basis for creation of Ukrainian Black-and-White dairy breed and now bred only in one breeding farm. Visual estimation of animal exterior showed good development of cows and calves and their belonging to the dairy type. In the vast majority the cows of the herd have a black suit, a white head with " glasses" around the eyes, white belly, udder, lower legs and brush of the tail. The youngsters aren’t consolidated by the exterior, and among them there are animals which are not typical for Ukrainian Whiteheaded breed. The young animals have some lag in live weight behind the breed standard [12] to 7 months’ age with exceeding of this trait in certain periods quite significantly in the future. It was established that selection of heifers on live weight will be effective at the early age (1-5 months), given the coefficient of variation of live weight – 22,63-30,21% and will not have a significant influence in the future. Milk yields of first-calf heifers vary considerably depending on the origin. The milk yield of first-calf heifers in the herd was 4238,5 kg on average, the heifers belonging to Mart 171 and Ozon 417 bloodlines had the best milk performance – 4483,1 and 4254,9 kg accordingly. The most aligned milk yield during the first lactation was in the cows belonging to Ozon 417 bloodline, the limits of the trait are 4128,5-4327,4 kg with the average value by the line 4254,9 kg. In contrast, the first-calf heifers of Ryezvyi 33 bloodline with average milk yield 4048,9 kg had limits of the trait 2199,3-4736,1 kg. Even greater range in cows’ milk yield during the first lactation R= 4939 kg (limits 1687 – 6626 kg) is characterized for the herd in general, it shows, on the one hand, the possibility of qualitative improvement of cows’ productivity due to selection on the investigated trait and lack of selection in the herd on the other hand. It was established that daughters of bull Chardash belonging to Ryezvyi 33 bloodline produced 4736,1 kg of milk for 305 days of the first lactation with fat content 3,6%, whereas Zlak’s descendants of the same line were characterized by the lowest milk yield for the first completed lactation – 2199,3 kg with fat content 3,7% and the average value by the line – 4048,9 kg of milk, fat content 3,6%. Similar variability of first-calf heifers’ milk yields, depending on the origin, is typical for other bloodlines of Ukrainian Whiteheaded breed. To increase milk productivity of Ukrainian Whiteheaded cows is recommended to repeat successful combinations of parental forms, and to preserve the breed – to carry out an objective assessment of animals by a range of traits, given the efficiency of selection of heifers on live weight at early age.

Enteric viruses in drinking water supplies

2002 ◽  
Vol 2 (3) ◽  
pp. 17-22
Author(s):  
A.P. Wyn-Jones ◽  
J. Watkins ◽  
C. Francis ◽  
M. Laverick ◽  
J. Sellwood
Keyword(s):  
Drinking Water ◽  
Heavy Rainfall ◽  
Liquid Culture ◽  
Plaque Assay ◽  
Enteric Viruses ◽  
Enteric Virus ◽  
The Other ◽  
Raw Water ◽  
Rt Pcr ◽  
Water Supplies

Two rural spring drinking water supplies were studied for their enteric virus levels. In one, serving about 30 dwellings, the water was chlorinated before distribution; in the other, which served a dairy and six dwellings the water was not treated. Samples of treated (40 l) and untreated (20 l) water were taken under normal and heavy rainfall conditions over a six weeks period and concentrated by adsorption/elution and organic flocculation. Infectious enterovirus in concentrates was detected in liquid culture and enumerated by plaque assay, both in BGM cells, and concentrates were also analysed by RT-PCR. Viruses were found in both raw water supplies. Rural supplies need to be analysed for viruses as well as bacterial and protozoan pathogens if the full microbial hazard is to be determined.

The assessment of biofilm community composition on plumbing materials in filtered and unfiltered water distribution systems

2003 ◽  
Vol 3 (1-2) ◽  
pp. 187-191
Author(s):  
M.M. Critchley ◽  
N.J. Cromar ◽  
H.J. Fallowfield
Keyword(s):  
Drinking Water ◽  
Fatty Acid ◽  
Community Composition ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution Systems ◽  
Polymer Materials ◽  
Fatty Acid Profiles ◽  
Water Supplies ◽  
Drinking Water Distribution Systems

Biofilms have been extensively characterised within drinking water distribution systems. However, the significance of materials on biofilm species diversity is not established. This study investigated the community composition of biofilms on plumbing materials receiving filtered and unfiltered water supplies. Biofilms were extracted from polybutylene, polyethylene, cross-linked polyethylene, unplasticised polyvinyl chloride and copper tubes in sampling rigs receiving Murray-Onkaparinga water before or after filtration. Biofilms were extracted and analysed for fatty acid composition using the FAME™ methodology. There were differences in the fatty acid profiles of biofilms and the respective water supplies, indicating differences in the attached and planktonic communities. The results also showed significant differences in the fatty acid profiles of biofilms on the polymer materials compared to copper, suggesting variations in biofilm populations on the different materials. The potential for materials to select for microbial populations has significant implications for the ecology of drinking water biofilms.

Water Quality and Health

1991 ◽  
Vol 23 (1-3) ◽  
pp. 201-209 ◽  
Author(s):  
W. Kreisel
Keyword(s):  
Water Quality ◽  
Developing Countries ◽  
Drinking Water ◽  
Water Supply ◽  
Human Health ◽  
Pollution Control ◽  
Wastewater Reuse ◽  
Water Supplies ◽  
Minimum Quality Standards ◽  
Quality Guidelines

Water quality can affect human health in various ways: through breeding of vectors, presence of pathogenic protozoa, helminths, bacteria and viruses, or through inorganic and organic chemicals. While traditional concern has been with pathogens and gastro-intestinal diseases, chemical pollutants in drinking-water supplies have in many instances reached proportions which affect human health, especially in cases of chronic exposure. Treatment of drinking-water, often grossly inadequate in developing countries, is the last barrier of health protection, but control at source is more effective for pollution control. Several WHO programmes of the International Drinking-Water Supply and Sanitation Decade have stimulated awareness of the importance of water quality in public water supplies. Three main streams have been followed during the eighties: guidelines for drinking-water quality, guidelines for wastewater reuse and the monitoring of freshwater quality. Following massive investments in the community water supply sector to provide people with adequate quantities of drinking-water, it becomes more and more important to also guarantee minimum quality standards. This has been recognized by many water and health authorities in developing countries and, as a result, WHO cooperates with many of them in establishing water quality laboratories and pollution control programmes.

Sign in / Sign up

Export Citation Format

Share Document