The Impact of Ammonia Photo-Oxidation Under UV Light from Low Pressure Mercury Lamps on Bromate Decay in Water

2006 ◽  
Vol 1 (4) ◽  
Author(s):  
Y. Beckles ◽  
V. Diyamandoglu

This research examines the influence of ammonia photo-oxidation on the reduction of the water contaminant, bromate (BrO3-) as a potential removal strategy. It has long been recognized that aqueous ammonia (NH3) has the potential to accelerate the photodecomposition of bromate. This phenomenon has never been studied in dilute solutions whereby its impact during water treatment with UV low-pressure lamps may be used advantageously. It is hypothesized that the accelerated rate of BrO3- photodecomposition in the presence of NH3 is attributed to the generation of an additional supply of electrons as ammonia photo-oxidation occurs. The findings revealed that the rate of bromate photo-decay is increased in the presence of ammonia even in dilute ammonia and BrO3- solutions and the reaction is further accelerated in basic solutions and solutions containing chloride ions. Nitrate is the final stable reaction product formed with prolonged irradiation, followed by a depression of pH. Hypobromous acid was undetected at these concentrations. It was also found that ammonia oxidation occurred in the presence of bromide ions even in acidic solution. The hypothesis that electrons are made available for electron scavengers when ammonia oxidation occurs was verified using sulphur hexafluoride as an electron scavenger.

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Fouad Fareh ◽  
Vincent Demers ◽  
Nicole R. Demarquette ◽  
Sylvain Turenne ◽  
Orlando Scalzo

The impact of binders and temperature on the rheological properties of feedstocks used in low-pressure powder injection molding was investigated. Experiments were conducted on different feedstock formulations obtained by mixing Inconel 718 powder with wax-based binder systems. The shear rate sensitivity index and the activation energy were used to study the degree of dependence of shear rate and temperature on the viscosity of the feedstocks. The injection performance of feedstocks was then evaluated using an analytical moldability model. The results indicated that the viscosity profiles of feedstocks depend significantly on the binder constituents, and the secondary binder constituents play an important role in the rheological behavior (pseudoplastic or near-Newtonian) exhibited by the feedstock formulations. Viscosity values as low as 0.06 to 2.9 Pa·s were measured at high shear rates and high temperatures. The results indicate that a feedstock containing a surfactant agent exhibits the best moldability characteristics.


2009 ◽  
Vol 39 (6) ◽  
pp. 1317-1339 ◽  
Author(s):  
Robert S. Pickart ◽  
Alison M. Macdonald ◽  
G. W. K. Moore ◽  
Ian A. Renfrew ◽  
John E. Walsh ◽  
...  

Abstract The seasonal change in the development of Aleutian low pressure systems from early fall to early winter is analyzed using a combination of meteorological reanalysis fields, satellite sea surface temperature (SST) data, and satellite wind data. The time period of the study is September–December 2002, although results are shown to be representative of the long-term climatology. Characteristics of the storms were documented as they progressed across the North Pacific, including their path, central pressure, deepening rate, and speed of translation. Clear patterns emerged. Storms tended to deepen in two distinct geographical locations—the Gulf of Alaska in early fall and the western North Pacific in late fall. In the Gulf of Alaska, a quasi-permanent “notch” in the SST distribution is argued to be of significance. The signature of the notch is imprinted in the atmosphere, resulting in a region of enhanced cyclonic potential vorticity in the lower troposphere that is conducive for storm development. Later in the season, as winter approaches and the Sea of Okhotsk becomes partially ice covered and cold, the air emanating from the Asian continent leads to enhanced baroclinicity in the region south of Kamchatka. This corresponds to enhanced storm cyclogenesis in that region. Consequently, there is a seasonal westward migration of the dominant lobe of the Aleutian low. The impact of the wind stress curl pattern resulting from these two regions of storm development on the oceanic circulation is investigated using historical hydrography. It is argued that the seasonal bimodal input of cyclonic vorticity from the wind may be partly responsible for the two distinct North Pacific subarctic gyres.


2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Lin Deng ◽  
Zhiren Wu ◽  
Caiqian Yang ◽  
Yung-Li Wang

This study’s objective was to study the photodegradation of TCNM (trichloronitromethane) in water under UV light. The effects of light intensity, nitrate ions, chloride ions, humic acid, and pH on the photochemical degradation of TCNM were investigated under the irradiation of low pressure mercury lamp (λ= 254 nm, 12 W). The photodegradation rate of TCNM was found to increase with increasing the concentration of nitrate ions, chloride ions, humic acid, pH, and light intensity. The photodegradation of TCNM was examined at pH 6.0 with initial concentrations (C0) of TCNM at 10.0–200.0 µg/L. The overall rate of degradation of TCNM was modeled using a pseudofirst-order rate law. Finally, the proposed mechanism involved in the photodegradation of TCNM was also discussed by analysis. Results of this study can contribute to the development of new source control strategies for minimization of TCNM risk at drinking water and wastewater utilities.


Author(s):  
Theodore S. Brockett ◽  
Jerzy T. Sawicki

A six-degree-of-freedom non-linear model is developed using Lagrange’s equation. The model is used to estimate transient fan-stage dynamic response during a fan-blade-out event in a turbo fan engine. The coupled degrees of freedom in the model include the fan whirl in the fan plane, the torsional response of the fan and low-pressure turbines (LPTs) about the engine centerline, the radial position of the released blade fragment, and the angular rotation of the trailing blade from its free state due to acceleration of the released blade. The released blade is assumed to slide radially outward along the trailing blade without friction. The external loading applied to the system includes fan imbalance, the remaining fan blades machining away the rub strip, rubbing of the blades with the fan case, and slowly-varying torques on the low pressure (LP) spool as engine performance degrades. The machining of the abradable imparts tangential loading on the fan blades as momentum is transferred to the liberated rub strip material. After application of the initial conditions including angular positions, angular velocities, released blade fragment position, and torsional wind-up, the governing equations are integrated forward in time from the instant the blade fragment is released. A reasonable match to test data is shown. Parameters affecting the fan-system response are varied to study the impact on fan peak lateral whirl amplitude, peak LP shaft torque, and peak loading on the trailing blade. It is found that the rub strip and mass eccentricity have the strongest influence on the LP shaft torsional loading. It is found that mass eccentricity has the largest influence on peak fan whirl. It is also found that released blade mass and attachment stiffness have the largest influence on the trailing blade loading.


2021 ◽  
Vol 11 (1) ◽  
pp. 56-62
Author(s):  
Sergej A. ANCIFEROV ◽  
Elena V. CHIRKOVA ◽  
Mariya N. KUCHERENKO

The reasons for the occurrence of an impact when closing a butt erfl y valve installed on pipelines that discharge sludge water from horizontal sedimentation tanks of treatment facilities are considered. The assumption about the possibility of water hammer was experimentally refuted. It is hypothesized that the cause of the impact is the disruption of the fl uid fl ow when fl owing around a fl at plate at critical angles of att ack. A numerical experiment was carried out, which consists in modeling the movement of a water fl ow in a completely fi lled, closed space of a pipe. As a result of the experiment, it was revealed that the fl ow stall was caused by the formation of zones of high and low pressure, respectively, before and after the valve. This provides additional energy to increase the closing torque, comparable to the force of a pneumatic actuator, and results in an impact.


2021 ◽  
Author(s):  
Rabiatou A. Diarra ◽  
Mohamed M. Traore ◽  
Amy M Junnila ◽  
Sekou F. Traore ◽  
Seydou Doumbia ◽  
...  

Abstract Background Attractive Toxic Sugar Baits (ATSBs) successfully reduced Anopheles mosquito vector populations and malaria parasite transmission in Mali, but application methods need to be improved for wide-scale use, and effects on non-target organisms (NTOs) must be assessed. The goals of this study were to determine on a village level the effect of different outdoor configurations of ATSB bait stations to 1) achieve > 25% Anopheles mosquito vector daily feeding rate for both males and females and 2) minimize the effect on non-target organisms. Methods Dye was added to Attractive Sugar Bait Stations (ASB – without toxin) to mark mosquitoes feeding on the sugar baits, and CDC UV light traps were used to monitor mosquitoes for the presence of the dye. Yellow plates, pitfall traps, Malaise traps, UV light traps, UV tray traps, and sweep nets were used to trap and sample non-target organisms (NTOs) for dye, indicating feeding on the ASB. ASB stations were hung on outer walls of village homes to determine the impact of different densities of ASBs (1,2, or 3 per home) as well as the impact of ASB height (1 m or 1.8 m above the ground on sugar feeding by anophelines. These experiments were carried out separately, on consecutive nights for mosquito and NTO monitoring. Eight villages in the Koulikoro province were chosen as the experimental locations. Results The use of one ASB station per house marked 23.11% of female and 7.11% of male An. gambiae s.l. While two and three ASB stations per house gave feeding rates above the 25% goal, there was no statistical difference in the percentage of marked mosquitoes (p=0.3141 females; p=0.9336 males). There was no difference in sugar feeding on ASB stations when hung at 1.0 and 1.8 m and (p=0.5170 females; p=0.9934 males); however, ASBs at 1.8 m had less accidental damage from village residents and animals, and subsequent invasion of non-targets through rips or holes produced. ASB stations at 1.8 m above ground were fed on by three of seven monitored insect orders. Feeding rates were less than 0.015% of total trap catches and as low as 0.0001%. The monitored orders were: Hymenoptera [ants (Formicidae), bees (Apidae), and wasps (Vespidae)], Lepidoptera (Rhopalocera, Bombyces, Geometroidea, Noctuoidea, Sphingidae, Pyraloidea), Coleoptera (Carabidae, Tenebrionidae, Scarabaeidae, Cerambycidae, and Chrysomelidae), Diptera (Brachycera, Chironomidae), Hemiptera (Cicadomorpha and Heteroptera), Neuroptera (Myrmeleontiformia) and Orthoptera (Caelifera and Ensifera). Using one or two stations limited evidence of NTO feeding to ants (Hymenoptera), Brachycera, Heteroptera, Noctuiodea, Rhopalocera, wasps (Vespidae) and wild bees (Apidae) (both Hymenoptera) and had a significantly reduced percentage of stained individuals compared to three stations which had the highest feeding rates amongst NTOs. The percentages of stained individuals were as follows: 6.84 ± 2.03% Brachycera were stained followed by wasps (Hymenoptera: Vespidae) 5.32 ± 2.27%, and Rhopalocera 2.22 ± 1.79%. Hanging the optimal number of stations per house for catching mosquitoes (two) 1.8 m above ground, limited the groups of non-targets to Brachycera, Chironomidae, Noctuoidea, Rhopalocera, parasitic wasps and wasps (both Hymenoptera: Vespidae). The three most commonly stained non-target insect groups at this height were wasps (Vespidae) (1.65 ± 0.75%), Chironomidae (0.99 ± 0.37), and Brachycera (1.55 ± 0.69%). Feeding at this height only occurred when stations were damaged.Conclusions The goal of marking one quarter of the total Anopheles mosquito vector population per day was obtained using 2 bait stations at 1.8 m height above the ground on the outer walls of houses. This configuration of ATSB stations also had minimal effects on non-target insects: only 0.0001% to 0.013% of specimens (in three orders) were marked. Stations hung 1.8 m above the ground had less accidental damage from passing people and livestock. The minimal marking of non-target insects may be attributed to visual orientation of non-mosquito insects while mosquitoes, are mostly guided by olfactory cues. Furthermore, the bait stations have a membrane cover, which if intact, is impenetrable to most sugar feeding non-target insects but is pierced by the stylets of the mosquito proboscis. Thus, most non-target insects are not exposed to the toxin even if they approach the bait stations.


2021 ◽  
Author(s):  
Yinghan Sang ◽  
Hong-Li Ren ◽  
Yi Deng ◽  
Xiaofeng Xu ◽  
Xueli Shi ◽  
...  

Abstract This paper reports findings from a diagnostic and modeling analysis that investigates the impact of the late-spring soil moisture anomaly over North Eurasia on the boreal summer rainfall over northern East Asia (NEA). Soil moisture in May in the region from the Kara-Laptev Sea coasts to Central Siberian Plateau is found to be negatively correlated with the summer rainfall from Mongolia to Northeast China. The atmospheric circulation anomalies associated with the anomalously dry soil are characterized by a pressure dipole with the high-pressure center located over North Eurasia and the low-pressure center over NEA, where an anomalous lower-level moisture convergence occurs, favoring rainfall formation. Diagnoses and Modeling experiments demonstrate that the effect of the spring low soil moisture over North Eurasia may persist into the following summer through modulating local surface latent and sensible heat fluxes, increasing low-level air temperature at higher latitudes, and effectively reducing the meridional temperature gradient. The weakened temperature gradient could induce the decreased zonal wind and the generation of a low-pressure center over NEA, associated with a favorable condition of local synoptic activity. The above relationships and mechanisms are vice versa for the prior wetter soil and decreased NEA rainfall. These findings suggest that soil moisture anomalies over North Eurasia may act as a new precursor providing an additional predictability source for better predicting the summer rainfall in NEA.


2016 ◽  
Vol 79 (1) ◽  
pp. 1-16 ◽  
Author(s):  
Charlotte Ann Roberts

Abstract This paper considers the discipline of palaeopathology, how it has developed, how it is studied, and what limitations present challenges to analysis. The study of disease has a long history and has probably most rapidly developed over the last 40-50 years with the development of methods, and particularly ancient pathogen DNA analysis. While emphasizing that palaeopathology has close synergies to evolutionary medicine, it focuses then on three ‘case studies’ that illustrate the close interaction people have had with their environments and how that has impacted their health. Upper and lower respiratory tract disease has affected sinuses and ribs, particularly in urban contexts, and tuberculosis in particular has been an ever present disease throughout thousands of years of our existence. Ancient DNA methods are now allowing us to explore how strains of the bacteria causing TB have changed through time. Vitamin D deficiency and ‘phossy jaw’ are also described, both potentially related to polluted environments, and possibly to working conditions in the industrial period. Access to UV light is emphasized as a preventative factor for rickets and where a person lives is important (latitude). The painful stigmatizing ‘phossy jaw’ appears to be a condition related to the match making industries. Finally, thoughts for the future are outlined, and two key concerns: a close consideration of ethical issues and human remains, especially with destructive analyses, and thinking more about how palaeopathological research can impact people beyond academia.


1994 ◽  
Vol 358 ◽  
Author(s):  
P. Steiner ◽  
F. Kozlowski ◽  
W. Lang

ABSTRACTIndium, tin, antimony and aluminum are deposited by an electrochemical process into the pores of n-type porous silicon which is anodized with ultraviolet light applied during formation. The presence of these metal atoms in the porous layer is checked by electron microprobe measurement. As reported previously, UV-light etched material shows red photoluminescence (630 nm) and blue electroluminescence (470 nm) without the metal treatment. After metal deposition the photoluminescence intensity decreases slightly (factor 0.5 - 0.8), whereas the spectral position remains constant. The electroluminescence efficiency is significantly enhanced by indium, aluminum and tin in the pores (factor 5 - 90). The tin and antimony treatment causes a red shift to 580 nm and 740 nm, respectively. The conductivity is slightly increased by all kinds of metals by a factor 2-5.


Sign in / Sign up

Export Citation Format

Share Document