scholarly journals Laboratory Investigation of Inorganic Fouling of Low Pressure UV Disinfection Lamps

2001 ◽  
Vol 36 (1) ◽  
pp. 71-92 ◽  
Author(s):  
M. Sheriff ◽  
M. Gehr
Keyword(s):  
Uv Light ◽  
Low Pressure ◽  
Bulk Precipitation ◽  
Batch Tests ◽  
Uv Irradiance ◽  
Theoretical Predictions ◽  
Flow Through ◽  
Inorganic Constituents ◽  
Uv Lamps ◽  
Solids Deposition

Abstract Iron(III) (mainly dosed as FeCl3) is one of the main inorganic constituents associated with the fouling of UV lamps during disinfection of wastewater. A low pressure mercury lamp UV system was operated under laboratory conditions to assess the effects of heat and UV light on fouling. Iron(III) was dosed at different concentrations and fouling was monitored by measuring the UV irradiance. The potential for ferric phosphate fouling and the effects of organics were also studied. Results showed that fouling did not occur in recirculating systems over 12 days of observation. However, in flow-through systems, the extent and rate of fouling depended on the solution Fe concentration. Furthermore, addition of phosphorus increased the fouling rate. Bulk precipitation appeared to be significant at iron(III) dosing over 3 mg/L. Theoretical predictions of an equilibrium model (MINEQL+) showed similar trends with measured concentrations of soluble Fe and P from batch tests. However, model predictions of temperature effects alone could not account for the observed solids deposition on the quartz sleeve. Bulk precipitation, followed by sedimentation, was considered to be the dominant mechanism at high iron (III) concentrations.

254 nm Radiant Efficiency of High Output Low Pressure Mercury Discharge Lamps with Neon-Argon Buffer Gas

2013 ◽  
Vol 325-326 ◽  
pp. 409-412
Author(s):  
Hao Jun Zhang ◽  
Qiu Yi Han ◽  
Shan Duan Zhang
Keyword(s):  
Mercury Vapor ◽  
Low Pressure ◽  
Input Power ◽  
Cold Spot ◽  
Outer Diameter ◽  
Buffer Gas ◽  
Uv Irradiance ◽  
Radiant Efficiency ◽  
Uv Lamps ◽  
High Output

High output low pressure mercury (LPM) discharge UV lamps have been briefly introduced. In order to measure the 254 nm radiant efficiency simply and preciously, Keitz formula was used and its advantage was illustrated. The LPM lamps had outer diameter of 19 mm (T6). The buffer gases are neon (65%) and argon (35%) with total pressure 1-10 Torr (133-1333 Pa). The lamps were operated with cold spot temperatures from 20°C to 80°C and discharge current from 0.8 A to 2.0 A. The electric field, input power, 254 nm UV irradiance and irradiance of other Hg lines from 265 to 579 nm in positive column were measured. The radiant power of each wavelength can be calibrated according to the 254 nm output and the Keitz formula. It was shown that the radiant efficiency of 254 nm can reach a maximum of above 40% at cold spot temperature 45-47 °C and current 1.6 A for filling pressure less than 3 Torr. The optimal mercury vapor pressure was 1.2 to 1.4 Pa. The output percentage of other Hg lines was below 5%. With the decrease of buffer gas pressure, the 254 nm radiant efficiency increased obviously.

Method to determine the power efficiency of UV disinfection plants and its application to low pressure plants for drinking water

2016 ◽  
Vol 17 (4) ◽  
pp. 947-957 ◽  
Author(s):  
Alois W. Schmalwieser ◽  
Georg Hirschmann ◽  
Alexander Cabaj ◽  
Regina Sommer
Keyword(s):  
Drinking Water ◽  
Electric Power ◽  
Power Efficiency ◽  
Electrical Power ◽  
Low Pressure ◽  
Uv Disinfection ◽  
Plant Type ◽  
Uv Irradiance ◽  
Flow Through ◽  
Selection Of

In this paper we present a method to determine the power efficiency of ultraviolet (UV) disinfection plants and apply this to low pressure plants for drinking water. In UV disinfection plants the water flow is regulated to ensure that microorganisms receive the necessary fluence for inactivation while passing through. The flow depends on the UV transmission (UVT) of the water. The lower the UVT of the water is, the less water may flow through the plant. UV irradiance is produced by lamps that consume, together with other components, electrical power and entail running costs. The power efficiency – electrical power versus disinfected volume – of a plant has therefore an important impact. Applying this method to different UV plants that are on the market shows that electric power of at least 5.3 Wh is necessary to disinfect 1 m3 of water possessing a UVT of 80% (100 mm), 8 Wh at 50% and 22 Wh at 10%. Further we found that ineffective design or a wrong selection of a plant may enhance these values by a factor of up to 7. This method enables not only the calculation of the power efficiency but also the decision for a certain plant type.

Influence of lamp intensity and water transmittance on the UV disinfection of water

1997 ◽  
Vol 35 (11-12) ◽  
pp. 113-118 ◽  
Author(s):  
R. Sommer ◽  
A. Cabaj ◽  
W. Pribil ◽  
T. Haider
Keyword(s):  
Supply Voltage ◽  
Uv Disinfection ◽  
Uv Detector ◽  
Uv Irradiance ◽  
Flow Through ◽  
Uv Lamp ◽  
Uv Transmittance ◽  
Two Parameters ◽  
Uv Lamps ◽  
Irradiation Chamber

The efficiency of UV disinfection devices depends on flow, lamp intensity and water transmittance. In practice the flow is controlled by suitable methods, whereas the other two parameters, to date, have not been taken into consideration sufficiently. The surveillance of the function of UV disinfection plants is routinely based on a sensor placed on the irradiation chamber wall. This measures changes of UV irradiance without differentiating if the effect is caused by transmittance or lamp intensity so that two different conditions of disinfection may occur at the same sensor readings. We investigated the influence of transmittance vs intensity on disinfection at the same sensor readings in a specially designed laboratory flow through UV irradiation system with one single UV lamp as well as in commercially available UV disinfection plants with multiple UV lamps. All devices were equipped with a calibrated selective UV detector connected to a UV radiometer. Lamp intensity was decreased by diminishing the supply voltage. UV transmittance was reduced by pumping aqueous sodium thiosulphate solution into the water inflow. The disinfection capacity was determined by measuring the reduction equivalent doses (RED) using a standardised biodosimetric method. We showed that equal sensor readings, either achieved by reducing the lamp intensity or by lowering the UV transmittance of the water, resulted in different REDs in one-lamp systems. The diminishing of UV intensity caused a greater decrease of REDs than reducing the water transmittance. However, in the multiple-lamp systems tested, equal sensor readings yielded equal REDs.

scholarly journals Demonstration and evaluation of germicidal UV-LEDs for point-of-use water disinfection

2010 ◽  
Vol 8 (3) ◽  
pp. 479-486 ◽  
Author(s):  
Christie Chatterley ◽  
Karl Linden
Keyword(s):  
Uv Irradiation ◽  
Uv Light ◽  
Low Pressure ◽  
Water Disinfection ◽  
Light Emitting ◽  
E Coli ◽  
Point Of Use ◽  
One Year ◽  
Uv Lamps ◽  
Uv Leds

Ultraviolet (UV) irradiation is a common disinfection option for water treatment in the developed world. There are a few systems installed in developing countries for point-of-use treatment, but the low-pressure mercury lamps currently used as the UV irradiation source have a number of sustainability issues including a fragile envelope, a lifetime of approximately one year, and they contain mercury. UV light emitting diodes (LEDs) may offer solutions to many of the sustainability issues presented by current UV systems. LEDs are small, efficient, have long lifetimes, and do not contain mercury. Germicidal UV LEDs emitting at 265 nm were evaluated for inactivation of E. coli in water and compared to conventional low-pressure UV lamps. Both systems provided an equivalent level of treatment. A UV-LED prototype was developed and evaluated as a proof-of-concept of this technology for a point-of-use disinfection option, and the economics of UV-LEDs were evaluated.

scholarly journals Study of mosquito attractants for photo catalytic mosquito trap

2013 ◽  
Vol 3 (1) ◽  
pp. 14
Author(s):  
Dewi Tristantini ◽  
Slamet ◽  
Angela Jessica Stephanie
Keyword(s):  
Activated Carbon ◽  
Air Temperature ◽  
Heat Production ◽  
Uv Light ◽  
Performance Testing ◽  
Humid Air ◽  
Combination Process ◽  
Photo Catalyst ◽  
Mosquito Trap ◽  
Uv Lamps

Photo catalytic mosquito trap is made of TiO2-Activated Carbon (AC) with a certain composition of AC. Research concerns on the heat spectrum which is produced by combination process of existing CO2 and humid air. The purpose of performance testing is to observe capability of this device in trapping mosquitoes related to the air temperature profile for heat spectrum is play important role for attracting mosquitoes. Result shows photo catalytic mosquito trap is more effective than devices which only consist of UV light or stream of CO2 and the humid air. A number of mosquitoes trapped by the photo catalyst coated panel configuration and UV lamps were lit proved far more effective because the heat production from recombination process. A little difference in temperature can be detected by mosquito. Keywords: Photo Catalytic, Mosquito, Recombination.

The Influence of Different Rim Seal Geometries on Hot-Gas Ingestion and Total Pressure Loss in a Low-Pressure Turbine

2010 ◽  
Author(s):  
P. Schuler ◽  
W. Kurz ◽  
K. Dullenkopf ◽  
H.-J. Bauer
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Gas Flow ◽  
Low Pressure ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Low Pressure Turbine ◽  
Hot Gas ◽  
Flow Through ◽  
Total Pressure Loss Coefficient

In order to prevent hot-gas ingestion into the rotating turbo machine’s inside, rim seals are used in the cavities located between stator- and rotor-disc. The sealing flow ejected through the rim seal interacts with the boundary layer of the main gas flow, thus playing a significant role in the formation of secondary flows which are a major contributor to aerodynamic losses in turbine passages. Investigations performed in the EU project MAGPI concentrate on the interaction between the sealing flow and the main gas flow and in particular on the influence of different rim seal geometries regarding the loss-mechanism in a low-pressure turbine passage. Within the CFD work reported in this paper static simulations of one typical low-pressure turbine passage were conducted containing two different rim seal geometries, respectively. The sealing flow through the rim seal had an azimuthal velocity component and its rate has been varied between 0–1% of the main gas flow. The modular design of the computational domain provided the easy exchange of the rim seal geometry without remeshing the main gas flow. This allowed assessing the appearing effects only to the change of rim seal geometry. The results of this work agree with well-known secondary flow phenomena inside a turbine passage and reveal the impact of the different rim seal geometries on hot-gas ingestion and aerodynamic losses quantified by a total pressure loss coefficient along the turbine blade. While the simple axial gap geometry suffers considerable hot-gas ingestion upstream the blade leading edge, the compound geometry implying an axial overlapping presents a more promising prevention against hot-gas ingestion. Furthermore, the effect of rim seals on the turbine passage flow field has been identified applying adequate flow visualisation techniques. As a result of the favourable conduction of sealing flow through the compound geometry, the boundary layer is less lifted by the ejected sealing flow, thus resulting in a comparatively reduced total pressure loss coefficient over the turbine blade.

Application of GE Low Load Package on an Existing District Heating Power Plant: A Case Study

2020 ◽  
Author(s):  
Antonio Mambro ◽  
Francesco Congiu ◽  
Francesco Piraccini
Keyword(s):  
Power Plant ◽  
Power Plants ◽  
District Heating ◽  
Low Pressure ◽  
Heating Power ◽  
Low Pressure Turbine ◽  
Low Load ◽  
Flow Through ◽  
Last Stage

Abstract The continuous increase of variable renewable energy and fuel cost requires steam turbine power plants to operate with high flexibility. Furthermore, the reduction in electricity price is forcing many existing and new district heating power plants to further optimize the heat production to maintain a sustainable business. This situation leads to low pressure steam turbines running at very low volume flow for an extended time. In this work, a case study of an existing 30 MWel district heating power plant located in Europe is presented. The customer request was the removal of the steam turbine last two stages along with the condenser to maximize steam delivery for district heating operations. However, based on the experience gained by GE on low load during the last years, the same heat production has been guaranteed without any significant impact on the existing unit, excluding any major modification of the plant layout such as last stage blading and condenser removal. Making use of the latest low flow modeling, the minimum cooling flow through the low-pressure turbine has been reduced by more than 90% compared to the existing unit. Optimization of the hood spray system and logic will reduce trailing edge erosion during low load operation leading to a significant extension in the last stage blade lifetime. These modifications, commercialized by GE as the Advanced Low Load Package (ALLP), provide a cheap, flexible and effective solution for the customer. With today’s knowledge, GE has the capability to guarantee low load operation minimizing the mass flow through the low-pressure turbine to the minimum required for safe operation. As a benefit to the customer, this option allows a gain in operational income of about 1.5 M€ per year.

A comparison of the efficacy of multiple ultraviolet light room decontamination devices in a radiology procedure room

2019 ◽  
Vol 40 (2) ◽  
pp. 158-163 ◽  
Author(s):  
Jennifer L. Cadnum ◽  
Annette L. Jencson ◽  
Scott A. Gestrich ◽  
Scott H. Livingston ◽  
Boris A. Karaman ◽  
...  
Keyword(s):  
Uv Light ◽  
Low Pressure ◽  
Laboratory Evaluation ◽  
Table Analysis ◽  
Patient Table ◽  
Set Up ◽  
Time Required ◽  
Cleaning And Disinfection ◽  
Uv C ◽  
Procedure Room

AbstractObjectiveTo evaluate the efficacy of multiple ultraviolet (UV) light decontamination devices in a radiology procedure room.DesignLaboratory evaluation.MethodsWe compared the efficacy of 8 UV decontamination devices with a 4-minute UV exposure time in reducing recovery of methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Enterococcus (VRE), and Clostridium difficile spores on steel disk carriers placed at 5 sites on a computed tomography patient table. Analysis of variance was used to compare reductions for the different devices. A spectrometer was used to obtain irradiance measurements for the devices.ResultsFour standard vertical tower low-pressure mercury devices achieved 2 log10CFU or greater reductions in VRE and MRSA and ~1 log10CFU reductions in C. difficile spores, whereas a pulsed-xenon device resulted in less reduction in the pathogens (P<.001). In comparison to the vertical tower low-pressure mercury devices, equal or greater reductions in the pathogens were achieved by 3 nonstandard low-pressure mercury devices that included either adjustable bulbs that could be oriented directly over the exam table, a robotic base allowing movement along the side of the table during operation, or 3 vertical towers operated simultaneously. The low-pressure mercury devices produced primarily UV-C light, whereas the pulsed-xenon device produced primarily UV-A and UV-B light. The time required to move the devices from the corner of the room and set up for operation varied from 18 to 59 seconds.ConclusionsMany currently available UV devices could provide an effective and efficient adjunct to manual cleaning and disinfection in radiology procedure rooms.

scholarly journals Assessment of the Effectiveness of Low-Pressure UV Light for Inactivation of Helicobacter pylori

2006 ◽  
Vol 72 (5) ◽  
pp. 3763-3765 ◽  
Author(s):  
Samuel L. Hayes ◽  
Karen M. White ◽  
Mark R. Rodgers
Keyword(s):  
Helicobacter Pylori ◽  
Water Treatment ◽  
Uv Light ◽  
Low Pressure ◽  
Pressure Source ◽  
Treatment Regimens ◽  
H Pylori

ABSTRACT Three strains of Helicobacter pylori were exposed to UV light from a low-pressure source to determine log inactivation versus applied fluence. Results indicate that H. pylori is readily inactivated at UV fluences typically used in water treatment regimens. Greater than 4-log10 inactivation was demonstrated on all three strains at fluences of less than 8 mJ cm−2.

Sign in / Sign up

Export Citation Format

Share Document