Modelling of rainfall induced infiltration into separate sewerage

1995 ◽  
Vol 32 (1) ◽  
pp. 161-168 ◽  
Author(s):  
N. Belhadj ◽  
C. Joannis ◽  
G. Raimbault
Keyword(s):  
Specific Model ◽  
Runoff Water ◽  
Sewer System ◽  
Rainfall Events ◽  
System Sensitivity ◽  
Complex Processes ◽  
Proposed Model ◽  
Parameter Interactions ◽  
Good Agreement

Flowrate changes in separate wastewater sewerage during wet weather are often attributed to inappropriate connections of runoff water. But these inputs are not the only cause of such behaviour and infiltration through leaking defects or cracks can supply large flows into collection pipes. The characterization of these flows is not an easy task since they involve complex processes, depending not only on rainfall events but also on hydrological conditions and seasons. Using 16 months of hourly measurements of rainfall and flowrates, we developed a six parameter conceptual model to simulate rainfall induced infiltration into a small sewer system. Sensitivity analysis applied to the proposed model showed good achievements under various calibration conditions but displayed high parameter interactions which may be a serious drawback for some specific model uses. Model application to another sewer network yielded good agreement between observed and simulated flows. The suitability of this model must be further checked on other sites.

Characterization of solid and metal element distributions in urban highway stormwater

1997 ◽  
Vol 36 (8-9) ◽  
pp. 155-160 ◽  
Author(s):  
John J. Sansalone ◽  
Steven G. Buchberger
Keyword(s):  
Particle Size ◽  
Treatment Strategies ◽  
Runoff Water ◽  
Element Analysis ◽  
Rainfall Events ◽  
Gravel Size ◽  
Metal Element ◽  
Mass Increase

Urban drainage from paved surfaces transports a wide gradation of solids ranging from sub-micron particles to gravel size aggregates. This study measured physical characteristics of solids transported in lateral pavement sheet flow from a heavily traveled urban roadway in Cincinnati. The physical characteristic measured was particle size which was used as a surrogate of specific surface area. Solids were sorted according to particle size distributions (PSD). Solids ranged from smaller than 1 μm to greater than 10,000 μm. Particles larger than 25 μm were separated mechanically to generate PSDs. Flow rate and duration controlled the yield and size of transported solids. Metal element analysis of PSD from snow and rainfall events indicate that Zn, Cu and Pb mass increase with decreasing particle size. Cd did not exhibit a similar trend. Results provide guidance for assessment of urban runoff water quality impacts and design of in-situ treatment strategies.

scholarly journals Vegetation Survival in Green Roofs without Irrigation

Water ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 136
Author(s):  
Anita Raimondi ◽  
Mariana Marchioni ◽  
Umberto Sanfilippo ◽  
Gianfranco Becciu
Keyword(s):  
Green Roofs ◽  
Medium Thickness ◽  
Rainfall Events ◽  
Continuous Simulation ◽  
Proposed Model ◽  
Growing Medium ◽  
Model Equations ◽  
Stormwater Control ◽  
Derivation Procedure ◽  
Good Agreement

The implementation of green roofs as sustainable urban drainage systems provides benefits for stormwater control and the environment and is more and more encouraged. A model for the estimation of the probability of vegetation survival without irrigation is proposed. The model, developed through a probabilistic analytical derivation procedure, can also consider the effects of chained rainfall events, without the need of continuous simulation of hydrological processes. The model equations can be useful in the design of green roofs, allowing to determine the growing medium thickness in terms of an assumed risk of vegetation withering in dry periods. The proposed model is also able to identify the optimal thickness of the growing medium, over which the survival performances can be increased only with irrigation. Model performances were tested by the application to two case studies in Italy. Comparison between the probabilities and the cumulative frequencies from a continuous simulation of water content in the growing medium shows a good agreement and provide a first confirmation of reliability.

Origins and characteristics of urban wet weather pollution in combined sewer systems: the experimental urban catchment “Le Marais” in Paris

1998 ◽  
Vol 37 (1) ◽  
pp. 35-43 ◽  
Author(s):  
Marie-Christine Gromaire-Mertz ◽  
Ghassan Chebbo ◽  
Mohamed Saad
Keyword(s):  
Waste Water ◽  
Sewer System ◽  
Urban Catchment ◽  
Rainfall Events ◽  
Sources Of Pollution ◽  
Sewer Systems ◽  
Combined Sewer ◽  
Wet Weather ◽  
Wet Weather Flow ◽  
Different Sources

An experimental urban catchment has been created in the centre of Paris, in order to obtain a description of the pollution of urban wet weather flows at different levels of the combined sewer system, and to estimate the contribution of runoff, waste water and sewer sediments to this pollution. Twenty-two rainfall events were studied from May to October 1996. Dry weather flow was monitored for one week. Roof, street and yard runoff, total flow at the catchment outlet and waste water were analysed for SS, VSS, COD and BOD5, on both total and dissolved fraction. Results show an evolution in the characteristics of wet weather flow from up to downstream: concentrations increase from the catchment entry to the outlet, as well as the proportion of particle-bound pollutants and the part of organic matter. A first evaluation of the different sources of pollution establishes that a major part of wet weather flow pollution originates from inside the combined sewer, probably through erosion of sewer sediments.

scholarly journals Compact Modelling of Electrical, Optical and Thermal Properties of Multi-Colour Power LEDs Operating on a Common PCB

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1286
Author(s):  
Krzysztof Górecki ◽  
Przemysław Ptak
Keyword(s):  
Integrated Circuits ◽  
Optical Model ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Junction Temperature ◽  
Optical Parameters ◽  
Spice Simulation ◽  
Light Emitting ◽  
Proposed Model ◽  
Good Agreement

This paper concerns the problem of modelling electrical, thermal and optical properties of multi-colour power light-emitting diodes (LEDs) situated on a common PCB (Printed Circuit Board). A new form of electro-thermo-optical model of such power LEDs is proposed in the form of a subcircuit for SPICE (Simulation Program with Integrated Circuits Emphasis). With the use of this model, the currents and voltages of the considered devices, their junction temperature and selected radiometric parameters can be calculated, taking into account self-heating phenomena in each LED and mutual thermal couplings between each pair of the considered devices. The form of the formulated model is described, and a manner of parameter estimation is also proposed. The correctness and usefulness of the proposed model are verified experimentally for six power LEDs emitting light of different colours and mounted on an experimental PCB prepared by the producer of the investigated devices. Verification was performed for the investigated diodes operating alone and together. Good agreement between the results of measurements and computations was obtained. It was also proved that the main thermal and optical parameters of the investigated LEDs depend on a dominant wavelength of the emitted light.

scholarly journals Characterization of Tiled Architecture for C-Band 1-Bit Beam-Steering Transmitarray

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1259
Author(s):  
Dmitry Kozlov ◽  
Irina Munina ◽  
Pavel Turalchuk ◽  
Vitalii Kirillov ◽  
Alexey Shitvov ◽  
...  
Keyword(s):  
Communication Systems ◽  
Beam Steering ◽  
Unit Cell ◽  
Electromagnetic Simulations ◽  
Fifth Generation ◽  
Full Wave ◽  
Array Architecture ◽  
Modulation Pattern ◽  
Good Agreement

A new implementation of a beam-steering transmitarray is proposed based on the tiled array architecture. Each pixel of the transmitarray is manufactured as a standalone unit which can be hard-wired for specific transmission characteristics. A set of complementary units, providing reciprocal phase-shifts, can be assembled in a prescribed spatial phase-modulation pattern to perform beam steering and beam forming in a broad spatial range. A compact circuit model of the tiled unit cell is proposed and characterized with full-wave electromagnetic simulations. Waveguide measurements of a prototype unit cell have been carried out. A design example of a tiled 10 × 10-element 1-bit beam-steering transmitarray is presented and its performance benchmarked against the conventional single-panel, i.e., unibody, counterpart. Prototypes of the tiled and single-panel C-band transmitarrays have been fabricated and tested, demonstrating their close performance, good agreement with simulations and a weak effect of fabrication tolerances. The proposed transmitarray antenna configuration has great potential for fifth-generation (5G) communication systems.

scholarly journals Characterization of rainfall events corresponding to forecasted conditions of potential hydrogeological risk

2020 ◽  
Vol 1614 ◽  
pp. 012077
Author(s):  
L Khramtsova ◽  
M Leonteva ◽  
M Mobilia ◽  
A Longobardi ◽  
E Nasyrova ◽  
...  
Keyword(s):  
Rainfall Events

scholarly journals Visco-Hyperelastic Characterization of the Equine Immature Zona Pellucida

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1223
Author(s):  
Elisa Ficarella ◽  
Mohammad Minooei ◽  
Lorenzo Santoro ◽  
Elisabetta Toma ◽  
Bartolomeo Trentadue ◽  
...  
Keyword(s):  
Zona Pellucida ◽  
Soft Matter ◽  
Mechanical Response ◽  
Mechanical Characterization ◽  
Nonlinear Material ◽  
Prony Series ◽  
Critical Comparison ◽  
Highly Nonlinear ◽  
Good Agreement

This article presents a very detailed study on the mechanical characterization of a highly nonlinear material, the immature equine zona pellucida (ZP) membrane. The ZP is modeled as a visco-hyperelastic soft matter. The Arruda–Boyce constitutive equation and the two-term Prony series are identified as the most suitable models for describing the hyperelastic and viscous components, respectively, of the ZP’s mechanical response. Material properties are identified via inverse analysis based on nonlinear optimization which fits nanoindentation curves recorded at different rates. The suitability of the proposed approach is fully demonstrated by the very good agreement between AFM data and numerically reconstructed force–indentation curves. A critical comparison of mechanical behavior of two immature ZP membranes (i.e., equine and porcine ZPs) is also carried out considering the information on the structure of these materials available from electron microscopy investigations documented in the literature.

Static and Dynamic Structure of Molecular Monomers and Dimers of the Rare-earth Fluorides

2001 ◽  
Vol 56 (5) ◽  
pp. 381-385
Author(s):  
Z. Akdeniz ◽  
M . Gaune-Escard ◽  
M. P. Tosi
Keyword(s):  
Rare Earth ◽  
Bond Length ◽  
Geometrical Structure ◽  
Vibrational Mode ◽  
Dynamic Structure ◽  
Molecular Shape ◽  
Proposed Model ◽  
Infrared Studies ◽  
Charged Clusters ◽  
Good Agreement

Abstract We determine a model of the ionic interactions in RF3 compounds, where R is a rare-earth element in the series from La to Lu, by an analysis of data on the bond length and the vibrational mode frequencies of the PrF3, GdF3 and HoF3 molecular monomers. All RF3 monomers are predicted to have a pyramidal shape, displaying a progressive flattening of the molecular shape in parallel with the lanthanide contraction of the bond length. The vibrational frequencies of all monomers are calculated, the results being in good agreement with the data from infrared studies of matrix-isolated molecules. We also evaluate the geometrical structure and the vibrational spectrum of the La2F6 and Ce2F6 dimers, as a further test of the proposed model. -PACS 36.40.Wa (Charged clusters)

Estimation of Interlayer Thickness in Inorganic Particulate-Filled Polymer Composites

2011 ◽  
Vol 24 (6) ◽  
pp. 777-788 ◽  
Author(s):  
J.Z. Liang
Keyword(s):  
Polymer Composites ◽  
Volume Fraction ◽  
Particle Diameter ◽  
Interfacial Structure ◽  
Interlayer Thickness ◽  
Filled Polymer ◽  
Mechanical And Physical Properties ◽  
The Relationship ◽  
Good Agreement

The structure of the interlayer between matrix and inclusions affect directly the mechanical and physical properties of inorganic particulate-filled polymer composites. The interlayer thickness is an important parameter for characterization of the interfacial structure. The effects of the interlayer between the filler particles and matrix on the mechanical properties of polymer composites were analyzed in this article. On the basis of a simplified model of interlayer, an expression for estimating the interlayer thickness ([Formula: see text]) was proposed. In addition, the relationship between the [Formula: see text] and the particle size and its concentration was discussed. The results showed that the calculations of the [Formula: see text] and thickness/particle diameter ratio ([Formula: see text]) increased nonlinearly with an increase of the volume fraction of the inclusions. Moreover, the predictions of [Formula: see text] and the relevant data reported in literature were compared, and good agreement was found between them.

scholarly journals Inflationary cosmology in unimodular F(T) gravity

2017 ◽  
Vol 32 (21) ◽  
pp. 1750114 ◽  
Author(s):  
Kazuharu Bamba ◽  
Sergei D. Odintsov ◽  
Emmanuel N. Saridakis
Keyword(s):  
Spectral Index ◽  
Teleparallel Gravity ◽  
Specific Model ◽  
Inflationary Cosmology ◽  
Model Parameters ◽  
De Sitter ◽  
Reconstruction Procedure ◽  
Additional Advantage ◽  
Slow Roll ◽  
Good Agreement

We investigate the inflationary realization in the context of unimodular F(T) gravity, which is based on the F(T) modification of teleparallel gravity, in which one imposes the unimodular condition through the use of Lagrange multipliers. We develop the general reconstruction procedure of the F(T) form that can give rise to a given scale-factor evolution, and then we apply it in the inflationary regime. We extract the Hubble slow-roll parameters that allow us to calculate various inflation-related observables, such as the scalar spectral index and its running, the tensor-to-scalar ratio, and the tensor spectral index. Then, we examine the particular cases of de Sitter and power-law inflation, of Starobinsky inflation, as well as inflation in a specific model of unimodular F(T) gravity. As we show, in all cases the predictions of our scenarios are in a very good agreement with Planck observational data. Finally, inflation in unimodular F(T) gravity has the additional advantage that it always allows for a graceful exit for specific regions of the model parameters.

Sign in / Sign up

Export Citation Format

Share Document