Stormwater retention basin efficiency regarding micropollutant loads and ecotoxicity

2013 ◽  
Vol 69 (5) ◽  
pp. 974-981 ◽  
Author(s):  
Christel Sébastian ◽  
Sylvie Barraud ◽  
Carolina Gonzalez-Merchan ◽  
Yves Perrodin ◽  
Régis Visiedo
Keyword(s):  
Polybrominated Diphenyl Ethers ◽  
Main Process ◽  
Sewer System ◽  
Run Off ◽  
Micropollutant Removal ◽  
In Situ Experiments ◽  
Retention Basin ◽  
Polycyclic Aromatic ◽  
Stormwater Retention

Retention basin efficiency in micropollutant removal has not been very well studied, in particular for pollutants highlighted by the European Water Framework Directive of 2000 such as pesticides, polybrominated diphenyl ethers (PBDEs) and alkylphenols. This study is based on in situ experiments carried out on a stormwater retention basin with the aim of estimating the basin efficiency in trapping and removing micropollutants from stormwater run-off from an industrial catchment drained by a separate sewer system. Along with stormwater, the basin receives some dry weather effluent flows, which are supposedly non-polluted. Ninety-four substances from five families (metals, polycyclic aromatic hydrocarbons (PAHs), PBDEs, alkylphenols and pesticides) were analyzed during 10 event campaigns in urban wet weather discharges at the inlet and outlet of the basin. The ecotoxicity of the samples was also tested. The results show high inter-event variability in both chemical and ecotoxic characteristics. They indicate good event efficiency concerning heavy metals and most PAHs. The studied pesticides, mainly found in the dissolved fraction, were not trapped. Particulate fraction study highlighted that settling is not the main process explaining micropollutant removal in a retention basin, as was noted for alkylphenols and PBDEs.

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

Electron and ion irradiation-induced dissolution of mechanical twins in the intermetalic U3Si: An in situ HVEM study

1989 ◽  
Vol 47 ◽  
pp. 652-653
Author(s):  
Charles W. Allen ◽  
Robert C. Birtcher
Keyword(s):  
Elevated Temperatures ◽  
Ion Irradiation ◽  
Ion Beam ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Heavy Ion ◽  
High Energy ◽  
Mechanical Twinning ◽  
In Situ Experiments

The uranium silicides, including U3Si, are under study as candidate low enrichment nuclear fuels. Ion beam simulations of the in-reactor behavior of such materials are performed because a similar damage structure can be produced in hours by energetic heavy ions which requires years in actual reactor tests. This contribution treats one aspect of the microstructural behavior of U3Si under high energy electron irradiation and low dose energetic heavy ion irradiation and is based on in situ experiments, performed at the HVEM-Tandem User Facility at Argonne National Laboratory. This Facility interfaces a 2 MV Tandem ion accelerator and a 0.6 MV ion implanter to a 1.2 MeV AEI high voltage electron microscope, which allows a wide variety of in situ ion beam experiments to be performed with simultaneous irradiation and electron microscopy or diffraction.At elevated temperatures, U3Si exhibits the ordered AuCu3 structure. On cooling below 1058 K, the intermetallic transforms, evidently martensitically, to a body-centered tetragonal structure (alternatively, the structure may be described as face-centered tetragonal, which would be fcc except for a 1 pet tetragonal distortion). Mechanical twinning accompanies the transformation; however, diferences between electron diffraction patterns from twinned and non-twinned martensite plates could not be distinguished.

A computer-control program for TEM in situ fatigue experiments

1989 ◽  
Vol 47 ◽  
pp. 620-621
Author(s):  
Kenneth S. Vecchio ◽  
John A. Hunt
Keyword(s):  
Slow Crack Growth ◽  
Computer Control ◽  
Control Program ◽  
Video Tape ◽  
Computer Control System ◽  
Transmission Electron ◽  
In Situ Experiments ◽  
Tremendous Amount ◽  
And Control

In-situ experiments conducted within a transmission electron microscope provide the operator a unique opportunity to directly observe microstructural phenomena, such as phase transformations and dislocation-precipitate interactions, “as they happen”. However, in-situ experiments usually require a tremendous amount of experimental preparation beforehand, as well as, during the actual experiment. In most cases the researcher must operate and control several pieces of equipment simultaneously. For example, in in-situ deformation experiments, the researcher may have to not only operate the TEM, but also control the straining holder and possibly some recording system such as a video tape machine. When it comes to in-situ fatigue deformation, the experiments became even more complicated with having to control numerous loading cycles while following the slow crack growth. In this paper we will describe a new method for conducting in-situ fatigue experiments using a camputer-controlled tensile straining holder.The tensile straining holder used with computer-control system was manufactured by Philips for the Philips 300 series microscopes. It was necessary to modify the specimen stage area of this holder to work in the Philips 400 series microscopes because the distance between the optic axis and holder airlock is different than in the Philips 300 series microscopes. However, the program and interfacing can easily be modified to work with any goniometer type straining holder which uses a penrmanent magnet motor.

Coliform transport in a pristine reservoir: modeling and field studies

1998 ◽  
Vol 37 (2) ◽  
pp. 137-144 ◽  
Author(s):  
Elisa Garvey ◽  
John E. Tobiason ◽  
Michael Hayes ◽  
Evelyn Wolfram ◽  
David A. Reckhow ◽  
...  
Keyword(s):  
Model Development ◽  
Fate And Transport ◽  
Field Studies ◽  
Meteorological Conditions ◽  
Reservoir Modeling ◽  
Vertical Circulation ◽  
Quality Model ◽  
Circulation Patterns ◽  
In Situ Experiments

This paper reports on field studies and model development aimed at understanding coliform fate and transport in the Quabbin Reservoir, an oligotrophic drinking water supply reservoir. An investigation of reservoir currents suggested the importance of wind driven phenomena, and that both lateral and vertical circulation patterns exist. In-situ experiments of coliform decay suggested dependence on light intensity and yielded an appropriate decay coefficient to be used in CE-QUAL-W2, a two-dimensional hydrodynamic and water quality model. Modeling confirmed the sensitivity of reservoir outlet concentration to vertical variability within the reservoir, meteorological conditions, and location of coliform source.

scholarly journals Upscaling THM modeling from small-scale to full-scale in-situ experiments in the Callovo-Oxfordian claystone

2021 ◽  
Vol 144 ◽  
pp. 104582
Author(s):  
D.M. Seyedi ◽  
C. Plúa ◽  
M. Vitel ◽  
G. Armand ◽  
J. Rutqvist ◽  
...  
Keyword(s):  
Full Scale ◽  
Small Scale ◽  
In Situ Experiments

scholarly journals Comparison of Hydrocarbon-Degrading Consortia from Surface and Deep Waters of the Eastern Mediterranean Sea: Characterization and Degradation Potential

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2246
Author(s):  
Georgia Charalampous ◽  
Efsevia Fragkou ◽  
Konstantinos A. Kormas ◽  
Alexandre B. De Menezes ◽  
Paraskevi N. Polymenakou ◽  
...  
Keyword(s):  
Mediterranean Sea ◽  
Oil Spills ◽  
Eastern Mediterranean ◽  
Sole Source ◽  
Eastern Mediterranean Sea ◽  
Deep Waters ◽  
Degradation Rates ◽  
Polycyclic Aromatic ◽  
Set Up

The diversity and degradation capacity of hydrocarbon-degrading consortia from surface and deep waters of the Eastern Mediterranean Sea were studied in time-series experiments. Microcosms were set up in ONR7a medium at in situ temperatures of 25 °C and 14 °C for the Surface and Deep consortia, respectively, and crude oil as the sole source of carbon. The Deep consortium was additionally investigated at 25 °C to allow the direct comparison of the degradation rates to the Surface consortium. In total, ~50% of the alkanes and ~15% of the polycyclic aromatic hydrocarbons were degraded in all treatments by Day 24. Approximately ~95% of the total biodegradation by the Deep consortium took place within 6 days regardless of temperature, whereas comparable levels of degradation were reached on Day 12 by the Surface consortium. Both consortia were dominated by well-known hydrocarbon-degrading taxa. Temperature played a significant role in shaping the Deep consortia communities with Pseudomonas and Pseudoalteromonas dominating at 25 °C and Alcanivorax at 14 °C. Overall, the Deep consortium showed a higher efficiency for hydrocarbon degradation within the first week following contamination, which is critical in the case of oil spills, and thus merits further investigation for its exploitation in bioremediation technologies tailored to the Eastern Mediterranean Sea.

scholarly journals Glacial melt disturbance shifts community metabolism of an Antarctic seafloor ecosystem from net autotrophy to heterotrophy

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Ulrike Braeckman ◽  
Francesca Pasotti ◽  
Ralf Hoffmann ◽  
Susana Vázquez ◽  
Angela Wulff ◽  
...  
Keyword(s):  
Carbon Balance ◽  
Benthic Communities ◽  
Benthic Primary Production ◽  
Community Metabolism ◽  
West Antarctic ◽  
Run Off ◽  
Net Heterotrophy ◽  
Benthic Ecosystems ◽  
The Antarctic

AbstractClimate change-induced glacial melt affects benthic ecosystems along the West Antarctic Peninsula, but current understanding of the effects on benthic primary production and respiration is limited. Here we demonstrate with a series of in situ community metabolism measurements that climate-related glacial melt disturbance shifts benthic communities from net autotrophy to heterotrophy. With little glacial melt disturbance (during cold El Niño spring 2015), clear waters enabled high benthic microalgal production, resulting in net autotrophic benthic communities. In contrast, water column turbidity caused by increased glacial melt run-off (summer 2015 and warm La Niña spring 2016) limited benthic microalgal production and turned the benthic communities net heterotrophic. Ongoing accelerations in glacial melt and run-off may steer shallow Antarctic seafloor ecosystems towards net heterotrophy, altering the metabolic balance of benthic communities and potentially impacting the carbon balance and food webs at the Antarctic seafloor.

scholarly journals Memory Effect on a LDH/zeolite A Composite: An XRD In Situ Study

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2102
Author(s):  
Breno G. P. Bezerra ◽  
Lindiane Bieseki ◽  
Mariele I. S. de Mello ◽  
Djalma R. da Silva ◽  
Cristiane B. Rodella ◽  
...  
Keyword(s):  
Memory Effect ◽  
Inert Atmosphere ◽  
Effect Study ◽  
Physical Mixture ◽  
Zeolite A ◽  
Three Samples ◽  
In Situ Experiments ◽  
Double Hydroxide ◽  
Rehydration Process

In this memory effect study, hydrotalcite-type compounds in the lamellar double hydroxide-like (LDH)/zeolite A composite material were analyzed using X-Ray Diffration XRD) in situ experiments. Three samples were analyzed: Al,Mg-LDH, Al,Mg-LDH/ZA composite, and a physical mixture (50/50 wt%) of zeolite A and Al,Mg-LDH. The Al,Mg-LDH sample was treated at 500 °C in an O2 atmosphere and subsequently rehydrated. The Al,Mg-LDH/ZA composites had three treatments: one was performed at 300 °C in a He atmosphere, and two treatments were performed with an O2 atmosphere at 300 and 500 °C. In the physical mixture, two treatments were carried out under O2 flow at 500 °C and under He flow at 300 °C. Both went through the rehydration process. All samples were also analyzed by energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). The results show that the LDH phase in the Al,Mg-LDH/ZA compounds has memory effects, and thus, the compound can be calcined and rehydrated. For the LDH in the composite, the best heat treatment system is a temperature of 300 °C in an inert atmosphere.

scholarly journals Advanced experimental approaches to marine water-column biogeochemical processes

2017 ◽  
Vol 75 (1) ◽  
pp. 30-42 ◽  
Author(s):  
Louis Legendre ◽  
Richard B Rivkin ◽  
Nianzhi Jiao
Keyword(s):  
Water Column ◽  
Numerical Models ◽  
Free Water ◽  
Sea Surface ◽  
Biogeochemical Processes ◽  
In Situ Experiments ◽  
Technological Developments ◽  
Approaches To Study ◽  
Experimental Approaches

Abstract This “Food for Thought” article examines the potential uses of several novel scientific and technological developments, which are currently available or being developed, to significantly advance or supplement existing experimental approaches to study water-column biogeochemical processes (WCB-processes). After examining the complementary roles of observation, experiments and numerical models to study WCB-processes, we focus on the main experimental approaches of free-water in situ experiments, and at-sea and on-land meso- and macrocosms. We identify some of the incompletely resolved aspects of marine WCB-processes, and explore advanced experimental approaches that could be used to reduce their uncertainties. We examine three such approaches: free-water experiments of lengthened duration using bioArgo floats and gliders, at-sea mesocosms deployed several 100s m below the sea-surface using new biogeochemical sensors, and 50 m-tall on-land macrocosms. These approaches could lead to significant progress in concepts related to marine WCB-processes.

Sign in / Sign up

Export Citation Format

Share Document