scholarly journals Fe-FeS2 adsorbent prepared with iron powder and pyrite by facile ball milling and its application for arsenic removal

2017 ◽  
Vol 76 (1) ◽  
pp. 192-200 ◽  
Author(s):  
Xiaobo Min ◽  
Yangwenjun Li ◽  
Yong Ke ◽  
Meiqing Shi ◽  
Liyuan Chai ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Ball Milling ◽  
Photoelectron Spectroscopy ◽  
Arsenic Removal ◽  
Molar Ratio ◽  
Arsenic Adsorption ◽  
Arsenic Uptake ◽  
X Ray ◽  
Before And After ◽  
High Arsenic

Arsenic is one of the major pollutants and a worldwide concern because of its toxicity and chronic effects on human health. An adsorbent of Fe-FeS2 mixture for effective arsenic removal was successfully prepared by mechanical ball milling. The products before and after arsenic adsorption were characterized with scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The adsorbent shows high arsenic removal efficiency when molar ratio of iron to pyrite is 5:5. The experimental data of As(III) adsorption are fitted well with the Langmuir isotherm model with a maximal adsorption capacity of 101.123 mg/g. And As(V) data were described perfectly by the Freundlich model with a maximal adsorption capacity of 58.341 L/mg. As(III) is partial oxidized to As(V) during the adsorption process. High arsenic uptake capability and cost-effectiveness of waste make it potentially attractive for arsenic removal.

scholarly journals Understanding the physicochemical properties of Zn–Fe LDH nanostructure as sorbent material for removing of anionic and cationic dyes mixture

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Rehab K. Mahmoud ◽  
Mohamed Taha ◽  
Amal Zaher ◽  
Rafat M. Amin
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Adsorption Process ◽  
Dye Adsorption ◽  
Chemical Properties ◽  
Cationic Dyes ◽  
Anionic Dyes ◽  
Visible Radiation ◽  
X Ray ◽  
Before And After

AbstractIn our work, the removal of cationic and anionic dyes from water was estimated both experimentally and computationally. We check the selectivity of the adsorbent, Zn–Fe layered double hydroxide (LDH) toward three dyes. The physical and chemical properties of the synthesis adsorbent before and after the adsorption process were investigated using X-ray photoelectron spectroscopy, energy dispersive X-ray, X-ray diffraction, FT-IR, HRTEM, and FESEM analysis, particle size, zeta potential, optical and electric properties were estimated. The effect of pH on the adsorption process was estimated. The chemical stability was investigated at pH 4. Monte Carlo simulations were achieved to understand the mechanism of the adsorption process and calculate the adsorption energies. Single dye adsorption tests revealed that Zn–Fe LDH effectively takes up anionic methyl orange (MO) more than the cationic dyes methylene blue (MB) and malachite green (MG). From MO/MB/MG mixture experiments, LDH selectively adsorbed in the following order: MO > MB > MG. The adsorption capacity of a single dye solution was 230.68, 133.29, and 57.34 mg/g for MO, MB, and MG, respectively; for the ternary solution, the adsorption capacity was 217.97, 93.122, and 49.57 mg/g for MO, MB, and MG, respectively. Zn–Fe LDH was also used as a photocatalyst, giving 92.2% and 84.7% degradation at concentrations of 10 and 20 mg/L, respectively. For visible radiation, the Zn–Fe LDH showed no activity.

scholarly journals Mg-Al Mixed Oxide Adsorbent Synthesized Using FCT Template for Fluoride Removal from Drinking Water

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Jifa Liu ◽  
Ping Zhao ◽  
Yue Xu ◽  
Xibin Jia
Keyword(s):  
Drinking Water ◽  
Adsorption Capacity ◽  
Mixed Oxide ◽  
Photoelectron Spectroscopy ◽  
Raw Materials ◽  
Molar Ratio ◽  
Fluoride Removal ◽  
Hydroxyl Groups ◽  
X Ray ◽  
Fluoride Adsorption

To make full use of natural waste, a novel Mg-Al mixed oxide adsorbent was synthesized by the dip-calcination method using the fluff of the chinar tree (FCT) and an Mg(II) and Al(III) chloride solution as raw materials. The adsorbents were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The effects of the Mg/Al molar ratio and calcination temperature on the performance of the novel Mg-Al mixed oxide adsorbent were investigated. The optimized Mg-Al mixed oxide adsorbent had a Langmuir adsorption capacity of 53 mg/g. This adsorption capacity was higher than that of the separate Mg oxide and Al oxide. The synergy between Mg and Al is beneficial to the adsorption performance of the material. The fluoride adsorption capacity of the optimized Mg-Al mixed oxide adsorbent is only slightly affected by ions such as Cl−, NO3−, SO42−, Na+, and K+and is excellent for use in recycling and real water. The hydroxyl groups on the surface of the Mg-Al mixed oxide adsorbent play a key role in the adsorption of fluorine. The as-obtained novel Mg-Al mixed oxide adsorbent is an efficient and environmentally friendly agent for fluoride removal from drinking water.

scholarly journals Selective and Highly Efficient Adsorption of a Mixture of Anionic and Cationic Dyes as Synthetic Wastewater Absorbents on Layered Double Hydroxide: Experimental and Computational Studies

2021 ◽  
Author(s):  
Rehab K. Mahmoud ◽  
Mohamed Taha ◽  
Amal Zaher ◽  
Rafat M. Amin
Keyword(s):  
Adsorption Capacity ◽  
Layered Double Hydroxide ◽  
Photoelectron Spectroscopy ◽  
Dye Adsorption ◽  
Cationic Dyes ◽  
Synthetic Wastewater ◽  
Anionic Dyes ◽  
X Ray ◽  
Before And After ◽  
Double Hydroxide

Abstract Background: In the current work, the removal of cationic and anionic dyes from water was studied both experimentally and computationally. We examine the selectivity of the adsorbent, Zn–Fe layered double hydroxide (LDH) toward three cationic and anionic dyes. Methods: The chemical and physical properties of the prepared adsorbent before and after adsorption were investigated using FT-IR, X-ray diffraction, zeta potential, energy dispersive X-ray, X-ray photoelectron spectroscopy, particle size, HRTEM, and FESEM analysis; optical and electric properties were estimated. The influence of pH on the adsorption process was estimated. Monte Carlo simulations were performed to understand the adsorption mechanism and compute the adsorption energies.Significant Findings: Single dye adsorption tests revealed that Zn–Fe LDH effectively takes up anionic methyl orange (MO) more than the cationic dyes methylene blue (MB) and malachite green (MG). From MO/MB/MG mixture experiments, LDH selectively adsorbed in the following order: MO>MB>MG. The adsorption capacity of a single dye solution was 230.68, 133.29, and 57.34 mg/g for MO, MB, and MG, respectively; for the ternary solution, the adsorption capacity was 217.97, 93.122, and 49.57 mg/g for MO, MB, and MG, respectively. Zn–Fe LDH was also used as a photocatalyst, giving 92.2% and 84.7% degradation at concentrations of 10 and 20 mg/L, respectively.

scholarly journals Photocatalytic Reduction of CO2 to Methanol Using a Copper-Zirconia Imidazolate Framework

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 346
Author(s):  
Sonam Goyal ◽  
Maizatul Shima Shaharun ◽  
Ganaga Suriya Jayabal ◽  
Chong Fai Kait ◽  
Bawadi Abdullah ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalyst Support ◽  
Oxidation Potential ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Optimum Parameters ◽  
Reduction Of Co2 ◽  
Enhanced Yield

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.

scholarly journals Evaluation of Fe-Mg Binary Oxide for As (III) Adsorption—Synthesis, Characterization and Kinetic Modelling

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 805
Author(s):  
Saif Ullah Khan ◽  
Rumman Zaidi ◽  
Feroz Shaik ◽  
Izharul Haq Farooqi ◽  
Ameer Azam ◽  
...  
Keyword(s):  
Arsenic Removal ◽  
Kinetic Modelling ◽  
Arsenic Concentration ◽  
Experimental Studies ◽  
Precipitation Method ◽  
Arsenic Adsorption ◽  
Adsorbent Dosage ◽  
X Ray ◽  
Co Precipitation ◽  
Contaminated Waters

Nanotechnology has received much attention in treating contaminated waters. In the present study, a facile co-precipitation method was employed to synthesize a novel iron and magnesium based binary metal oxide using a stoichiometrically fixed amount of FeNO3.9H2O and MgNO3.6H2O in a proportion of molar concentration 1:1 and was later evaluated in removing As (III) from contaminated waters. Characterization of the prepared nanomaterial was done using X-ray diffraction (XRD), scanning electron microscopy (SEM), Energy Dispersive X-Ray Analysis (EDAX) and ultraviolet–visible spectrophotometry (UV-VIS). Experimental studies on batch scale were carried out, examining the effect of varying initial concentrations of metal, adsorbent dosage, application time and initial pH on removal efficiency. Arsenic removal increased on increasing adsorbent dosage (0.1–1 g/L) but trend reversed on increasing initial arsenic concentration attaining qmax of 263.20 mg/g. Adsorption was quite efficient in pH range 4–8. Freundlich fitted better for adsorption isotherm along with following Pseudo-2nd order kinetics. The reusability and effect of co-existing ions on arsenic adsorption, namely SO42−, CO32− and PO43− were also explored with reusability in 1st and 2nd cycles attained adsorptive removal up to 77% and 64% respectively. The prepared nano-adsorbent showed promising results in terms of high arsenic uptake (qmax of 263.20 mg/g) along with facile and cost-effective synthesis. Thus, the co-precipitation technique used in this work is a simple one step procedure without any use of any precursor as compared to most of the other procedures used for synthesis.

scholarly journals Pristine and Magnetic Kenaf Fiber Biochar for Cd2+ Adsorption from Aqueous Solution

2021 ◽  
Vol 18 (15) ◽  
pp. 7949
Author(s):  
Anwar Ameen Hezam Saeed ◽  
Noorfidza Yub Harun ◽  
Suriati Sufian ◽  
Muhammad Roil Bilad ◽  
Zaki Yamani Zakaria ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Textural Properties ◽  
Ion Concentration ◽  
Solution Temperature ◽  
Maximum Adsorption Capacity ◽  
Magnetic Biochar ◽  
X Ray ◽  
Study Results ◽  
Capacity Surface

Development of strategies for removing heavy metals from aquatic environments is in high demand. Cadmium is one of the most dangerous metals in the environment, even under extremely low quantities. In this study, kenaf and magnetic biochar composite were prepared for the adsorption of Cd2+. The synthesized biochar was characterized using (a vibrating-sample magnetometer VSM), Scanning electron microscopy (SEM), X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The adsorption batch study was carried out to investigate the influence of pH, kinetics, isotherm, and thermodynamics on Cd2+ adsorption. The characterization results demonstrated that the biochar contained iron particles that help in improving the textural properties (i.e., surface area and pore volume), increasing the number of oxygen-containing groups, and forming inner-sphere complexes with oxygen-containing groups. The adsorption study results show that optimum adsorption was achieved under pH 5–6. An increase in initial ion concentration and solution temperature resulted in increased adsorption capacity. Surface modification of biochar using iron oxide for imposing magnetic property allowed for easy separation by external magnet and regeneration. The magnetic biochar composite also showed a higher affinity to Cd2+ than the pristine biochar. The adsorption data fit well with the pseudo-second-order and the Langmuir isotherm, with the maximum adsorption capacity of 47.90 mg/g.

scholarly journals Synthesis of Novel Arginine-Based Flame Retardant and Its Application in Lyocell Fabric

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3588
Author(s):  
Jiayi Chen ◽  
Yansong Liu ◽  
Jiayue Zhang ◽  
Yuanlin Ren ◽  
Xiaohui Liu
Keyword(s):  
Fourier Transform ◽  
Heat Release ◽  
Flame Retardant ◽  
Photoelectron Spectroscopy ◽  
Fourier Transform Infrared ◽  
Ftir Analysis ◽  
Excellent Thermal Stability ◽  
X Ray ◽  
Cone Calorimeter Test ◽  
Before And After

Lyocell fabrics are widely applied in textiles, however, its high flammability increases the risk of fire. Therefore, to resolve the issue, a novel biomass-based flame retardant with phosphorus and nitrogen elements was designed and synthesized by the reaction of arginine with phosphoric acid and urea. It was then grafted onto the lyocell fabric by a dip-dry-cure technique to prepare durable flame-retardant lyocell fabric (FR-lyocell). X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) analysis demonstrated that the flame retardant was successfully introduced into the lyocell sample. Thermogravimetric (TG) and Raman analyses confirmed that the modified lyocell fabric featured excellent thermal stability and significantly increased char residue. Vertical combustion results indicated that FR-lyocell before and after washing formed a complete and dense char layer. Thermogravimetric Fourier-transform infrared (TG-FTIR) analysis suggested that incombustible substances (such as H2O and CO2) were produced and played a significant fire retarding role in the gas phase. The cone calorimeter test corroborated that the peak of heat release rate (PHRR) and total heat release (THR) declined by 89.4% and 56.4%, respectively. These results indicated that the flame retardancy of the lyocell fabric was observably ameliorated.

scholarly journals Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 942 ◽  
Author(s):  
Huo-Xi Jin ◽  
Hong Xu ◽  
Nan Wang ◽  
Li-Ye Yang ◽  
Yang-Guang Wang ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Langmuir Isotherm ◽  
Adsorption Equilibrium ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Metal Organic ◽  
Langmuir Isotherm Model

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5–CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5–CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R2 = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5–CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.

Low-temperature route to nanoscale P3N5 hollow spheres

2003 ◽  
Vol 18 (10) ◽  
pp. 2359-2363 ◽  
Author(s):  
Hongzhou Gu ◽  
Yunle Gu ◽  
Zhefeng Li ◽  
Yongcheng Ying ◽  
Yitai Qian
Keyword(s):  
Photoelectron Spectroscopy ◽  
Hollow Spheres ◽  
Molar Ratio ◽  
Visible Absorption ◽  
X Ray ◽  
Transmission Electron ◽  
Influence Of Temperature On ◽  
Wide Gap ◽  
20 Nm ◽  
High Degree

Nanoscale hollow spheres of amorphous phosphorus nitride (P3N5) were synthesized by reacting PCl3 with NaN3 at 150–250 °C. Transmission electron microscope images show that the hollow spheres have a diameter of 150–350 nm, and the thickness of the shell is 20 nm. A very small amount of curly films were also found in the sample prepared at 150 °C. The infrared spectrum indicates a high degree of purity. X-ray photoelectron spectroscopy indicates the presence of P and N, with a molar ratio of 1:1.62 for P:N. Ultraviolet-visible absorption spectroscopy shows an absorption band at 265–315 nm. Under photoluminescent excitation at 230 nm, the P3N5 emits ultraviolet light at 305 nm. With a band gap of 4.28 eV, the products may be a wide gap semiconductor. A possible mechanism and the influence of temperature on the formation of the hollow spheres are also discussed.

Oxidation of Alloy-X in Subcritical, Transition, and Supercritical Water

CORROSION ◽  
10.5006/3881 ◽  
2021 ◽  
Author(s):  
Zachary Karmiol ◽  
Dev Chidambaram
Keyword(s):  
Supercritical Water ◽  
Photoelectron Spectroscopy ◽  
Focused Ion Beam ◽  
Elevated Temperatures ◽  
Subcritical Water ◽  
Ion Beam ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nickel Based Superalloy ◽  
Before And After

This work investigates the oxidation of a nickel based superalloy, namely Alloy X, in water at elevated temperatures: subcritical water at 261°C and 27 MPa, the transition between subcritical and supercritical water at 374°C and 27 MPa, and supercritical water at 380°C and 27 MPa for 100 hours. The morphology of the sample surfaces were studied using scanning electron microscopy coupled with focused ion beam milling, and the surface chemistry was investigated using X-ray diffraction, Raman spectroscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy before and after exposure studies. Surfaces of all samples were identified to comprise of a ferrite spinel containing aluminum.

Sign in / Sign up

Export Citation Format

Share Document