scholarly journals Agricultural biowaste, rice bran, as carbon source to enhance biomass and lipid production: analysis with various growth rate models

2020 ◽  
Vol 82 (6) ◽  
pp. 1120-1130
Author(s):  
H. J. Choi
Keyword(s):  
Growth Rate ◽  
Carbon Source ◽  
Rice Bran ◽  
Lipid Content ◽  
Mass Culture ◽  
Low Cost ◽  
Lipid Production ◽  
Substrate Inhibition ◽  
Good Alternative ◽  
High Lipid

Abstract As a byproduct of agriculture, rice bran can be a good alternative carbon source to mass-produce microalgae and increase lipid content. The purpose of this study was to investigate the effects of rice bran extract (RBE) on the mass culture and oil content of microalgae. Various parameters were applied to the growth rate model to explain the dynamics of substrate inhibition and growth of microalgae. The rice bran contains 46.1% of carbohydrates, in which is 38.3% glucose, and is very suitable as a carbon source for microalgae growth. The culture with RBE had a four times higher biomass production than microalgae cultured on Jaworski's medium (JM) with a small amount of 1 g/L. In addition, for RBE, the lipid content was three times higher and saturated fatty acid was 3% lower than were those of JM. According to the above results, when Chlorella vulgaris is cultured using RBE, a high amount of biomass and high lipid content can be obtained with a small amount of RBE. RBE is a discarded waste and has a high content of glucose, so it can be replaced by an organic carbon source to increase microbial biomass growth and lipid content at low cost.

scholarly journals Evaluating the Potential of Rhodosporidium toruloides-1588 for High Lipid Production Using Undetoxified Wood Hydrolysate as a Carbon Source

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5960
Author(s):  
Rahul Saini ◽  
Krishnamoorthy Hegde ◽  
Carlos Saul Osorio-Gonzalez ◽  
Satinder Kaur Brar ◽  
Pierre Vezina
Keyword(s):  
Carbon Source ◽  
Low Cost ◽  
Lipid Production ◽  
Rhodosporidium Toruloides ◽  
Biofuel Production ◽  
Sugar Consumption ◽  
High Lipid ◽  
Lipid Characterization ◽  
Forestry Residues ◽  
Wood Hydrolysate

The study aims to explore microbial lipid production using an abundant and low-cost lignocellulosic biomass derived from forestry residues. Sugar-rich undetoxified hydrolysate was prepared using hardwood and softwood sawdust and used for lipid production as a carbon source from an oleaginous yeast, Rhodosporidium toruloides-1588. The maximum biomass obtained was 17.09 and 19.56 g/L in hardwood and softwood hydrolysate, respectively. Sugar consumption in both hydrolysates was >95%, with a maximum lipid accumulation of 36.68% at 104 h and 35.24% at 96 h. Moreover, R. toruloides-1588 exhibited tolerance to several toxic compounds such as phenols, organic acids and furans present in hydrolysates. The lipid characterization showed several monosaturated and polyunsaturated fatty acids, making it a potential feedstock for biofuels and oleochemicals production. This study confirms the credibility of R. toruloides-1588 as a suitable lipid producer using hydrolysates from forestry residues as a substrate. Additionally, lipids obtained from R. toruloides-1588 could be a potential feedstock for advanced biofuel production as well as for food and pharmaceutical applications.

Characteristics of the growth rate and lipid production in fourteen strains of Baltic green microalgae

2018 ◽  
Vol 47 (1) ◽  
pp. 10-18 ◽  
Author(s):  
Marek Klin ◽  
Filip Pniewski ◽  
Adam Latała
Keyword(s):  
Growth Rate ◽  
Mass Culture ◽  
Lipid Production ◽  
Growth Patterns ◽  
Green Microalgae ◽  
Yield Improvement ◽  
Final Cell Density ◽  
Lipid Yield ◽  
Green Algal ◽  
High Lipid

Abstract Screening of fourteen Baltic green algal strains provided basic data on their mass culture potential for the purpose of valuable biomass production with particular emphasis on lipid content. Selected microalgae were grown under non-stressed conditions in order to identify those characterized by efficient lipid production. The tested strains exhibited significant differences in growth patterns and lipid yields. Strains belonging to Chlorella and Stichococcus genera exhibited the highest growth rates, ranging from 0.39 d-1 to 0.50 d-1 and thus the highest final cell density (> 107 cells ml-1). Furthermore, five strains: C. minutissima BA-12, C. fusca BA-18, C. vulgaris BA-80, Monoraphidium sp. BA-165 and Chlorella sp. BA-167 were characterized by distinctively high lipid yield (> 60 mg l-1). The same strains, together with C. vulgaris BA-02, were also shown as those with the highest volumetric lipid productivity, reaching > 30 mg l-1 d-1. The tested Baltic strains performed well in terms of lipid production compared to the literature data, still leaving a great spectrum of opportunities for further lipid yield improvement.

Optimization of lipid accumulation in Pleurastrum insigne for biodiesel production

2021 ◽  
Vol 16 (10) ◽  
pp. 144-155
Author(s):  
Van Lal Michael Chhandama ◽  
Belur Kumudini Satyan
Keyword(s):  
Lipid Content ◽  
Lipid Production ◽  
Statistical Design ◽  
High Growth ◽  
High Growth Rate ◽  
Biodiesel Production ◽  
Nitrogen And Phosphorus ◽  
Biodiesel Standards ◽  
High Lipid ◽  
Different Sources

Microalgae emerged as a competent feedstock for biodiesel production because of high growth rate and lipid content. This work focuses on isolation of novel microalgal strain from different sources of water for the production of biodiesel. The isolated microalgae, Pleurastrum insigne possessed high lipid content (~28 % dcw), further optimized to 57.06 % dcw using a statistical design (CCD) under Response Surface Methodology. Lipid production was optimized by nutrient (nitrogen and phosphorus) and pH stress. The different type of fatty acids present in the optimized lipid was also profiled using GCMS. Biodiesel yield was found to be 82.14 % of the total lipid and the fuel properties tested have met IS, ASTM and EN biodiesel standards.

scholarly journals Biomass and lipid induction strategies in microalgae for biofuel production and other applications

2019 ◽  
Vol 18 (1) ◽  
Author(s):  
Hossein Alishah Aratboni ◽  
Nahid Rafiei ◽  
Raul Garcia-Granados ◽  
Abbas Alemzadeh ◽  
José Rubén Morones-Ramírez
Keyword(s):  
Lipid Content ◽  
Large Scale ◽  
Fossil Fuels ◽  
Low Cost ◽  
Lipid Production ◽  
Arable Land ◽  
Economic Cost ◽  
Biofuel Production ◽  
Scale Production ◽  
Microalgae Biomass

Abstract The use of fossil fuels has been strongly related to critical problems currently affecting society, such as: global warming, global greenhouse effects and pollution. These problems have affected the homeostasis of living organisms worldwide at an alarming rate. Due to this, it is imperative to look for alternatives to the use of fossil fuels and one of the relevant substitutes are biofuels. There are different types of biofuels (categories and generations) that have been previously explored, but recently, the use of microalgae has been strongly considered for the production of biofuels since they present a series of advantages over other biofuel production sources: (a) they don’t need arable land to grow and therefore do not compete with food crops (like biofuels produced from corn, sugar cane and other plants) and; (b) they exhibit rapid biomass production containing high oil contents, at least 15 to 20 times higher than land based oleaginous crops. Hence, these unicellular photosynthetic microorganisms have received great attention from researches to use them in the large-scale production of biofuels. However, one disadvantage of using microalgae is the high economic cost due to the low-yields of lipid content in the microalgae biomass. Thus, development of different methods to enhance microalgae biomass, as well as lipid content in the microalgae cells, would lead to the development of a sustainable low-cost process to produce biofuels. Within the last 10 years, many studies have reported different methods and strategies to induce lipid production to obtain higher lipid accumulation in the biomass of microalgae cells; however, there is not a comprehensive review in the literature that highlights, compares and discusses these strategies. Here, we review these strategies which include modulating light intensity in cultures, controlling and varying CO2 levels and temperature, inducing nutrient starvation in the culture, the implementation of stress by incorporating heavy metal or inducing a high salinity condition, and the use of metabolic and genetic engineering techniques coupled with nanotechnology.

Effects of different lipid contents on growth of earthworms and the products during vermicomposting

2019 ◽  
Vol 37 (9) ◽  
pp. 934-940 ◽  
Author(s):  
Zexuan Wu ◽  
Bangyi Yin ◽  
Xu Song ◽  
Qi Zhao
Keyword(s):  
Lipid Content ◽  
Low Cost ◽  
Nitrifying Bacteria ◽  
Available Phosphorus ◽  
Negative Effects ◽  
Kitchen Waste ◽  
Lipid Contents ◽  
High Lipid ◽  
Carbon Nitrogen Ratio ◽  
Chemical Characters

In China, the production of kitchen waste was more than 97 million tons per year in 2016. The high lipid content of kitchen waste makes it hard to degrade. Vermicomposting is a kind of low-cost biotechnology through the combination of earthworms and microbes, which could be considered in converting kitchen waste to valuable products. However, the effect of the lipid in kitchen waste on earthworms and composting is not known yet. The objective of this study was to analyze the effects of lipid on vermicomposting and to derive the most suitable lipid content in vermicomposting. In our study, kitchen waste with four different lipid contents was prepared: 0% (A), 5% (B), 10% (C) and 15% (D). The earthworm growth and chemical characters of substrates were measured at the interim (14 days) and the end (28 days) of vermicomposting. Our results showed that the high content of lipid had negative effects on growth of earthworms and products in vermicomposting. The kitchen waste with lower lipid content could be better composted by earthworms. The average body weight of the earthworm increased by 9% in treatment A. Total nitrogen, available phosphorus, available potassium and nitrate nitrogen of treatment A with 0% (measured value: 5%) lipid content were significantly higher than those in other treatments. Meanwhile, treatment A had the lowest carbon/nitrogen ratio which might be due to hindrances in the breathing and activities of earthworms. The high content of lipid makes growth of aerobic bacteria such as nitrifying bacteria difficult.

scholarly journals A Mathematical Model of Neutral Lipid Content in terms of Initial Nitrogen Concentration and Validation in Coelastrum sp. HA-1 and Application in Chlorella sorokiniana

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Zhenhua Yang ◽  
Yue Zhao ◽  
Zhiyong Liu ◽  
Chenfeng Liu ◽  
Zhipeng Hu ◽  
...  
Keyword(s):  
Protein Synthesis ◽  
Lipid Content ◽  
Lipid Accumulation ◽  
Nitrogen Concentration ◽  
Lipid Production ◽  
Lipid Synthesis ◽  
Quantitative Relationship ◽  
Chlorella Sorokiniana ◽  
High Lipid ◽  
Nitrogen Concentrations

Microalgae are considered to be a potential major biomass feedstock for biofuel due to their high lipid content. However, no correlation equations as a function of initial nitrogen concentration for lipid accumulation have been developed for simplicity to predict lipid production and optimize the lipid production process. In this study, a lipid accumulation model was developed with simple parameters based on the assumption protein synthesis shift to lipid synthesis by a linear function of nitrogen quota. The model predictions fitted well for the growth, lipid content, and nitrogen consumption of Coelastrum sp. HA-1 under various initial nitrogen concentrations. Then the model was applied successfully in Chlorella sorokiniana to predict the lipid content with different light intensities. The quantitative relationship between initial nitrogen concentrations and the final lipid content with sensitivity analysis of the model were also discussed. Based on the model results, the conversion efficiency from protein synthesis to lipid synthesis is higher and higher in microalgae metabolism process as nitrogen decreases; however, the carbohydrate composition content remains basically unchanged neither in HA-1 nor in C. sorokiniana.

Enhanced Microalgal Lipid Production in Internally Illuminated Airlift Photobioreactor

2019 ◽  
Vol 53 (2) ◽  
pp. 38-45
Author(s):  
Irem Deniz ◽  
Zeliha Demirel ◽  
Esra Imamoglu ◽  
Meltem Conk Dalay
Keyword(s):  
Fatty Acids ◽  
Growth Rate ◽  
Blue Light ◽  
Lipid Content ◽  
White Light ◽  
Lipid Production ◽  
Red Light ◽  
Light Spectrum ◽  
Light Supply ◽  
Total Fatty Acids

AbstractInternal illumination systems are being considered for use as an alternative light supply technique in microalgal products. The main goal of the study was to analyze the roles of different light wavelengths in internally illuminated airlift photobioreactors (PBRs) providing the light energy in an efficient way for the biomass production, lipid yield, and fatty acid composition of Amphora capitellata. The maximum chlorophyll-a concentration per unit biomass (2.62 ± 0.16 mg L−1) was obtained under red light, which was only 14% higher than under blue light in internally illuminated airlift PBR, whereas low chlorophyll-a content was found under white light. Maximum specific growth rate of 0.317 day−1, which corresponded to a doubling time of 2.185 days, was obtained under red light for A. capitellata. It was found that lipid content increased with decreasing growth rate for A. capitellata. Palmitic acid (C16:0) and palmitoleic acid (C16:1) were the principal fatty acids accounting for between 31%‐33% and 31%‐32% of total fatty acids, respectively. It is important to underline that red and blue light spectrum ranges contribute to improved biomass growth, whereas white light has the potential to support lipid content of diatoms.

Sign in / Sign up

Export Citation Format

Share Document