scholarly journals Effect of Coating Thickness on Bond Behaviors of Polymer Cement Coated Plain Steel Bar with Concrete and Finite Element Modeling

2016 ◽  
Vol 10 (1) ◽  
pp. 571-577 ◽  
Author(s):  
Xiong Yuanliang ◽  
Wang Kunrong ◽  
Liu Zhiyong ◽  
Yang Zhengguang
Keyword(s):  
Finite Element ◽  
Bond Strength ◽  
Coating Thickness ◽  
Failure Modes ◽  
Bond Behavior ◽  
Finite Element Software ◽  
Pullout Tests ◽  
Steel Bar ◽  
Contact Surfaces ◽  
Hot Rolled

The pullout tests were carried out to investigate the effect of coating thickness on bond behavior (failure modes, bond strength, bond stress slip curves) between hot rolled plain steel bar (HPB) coated with polymer cement based coating and concrete. The results indicated the failure mode of the specimens is pullout. Suitable coating thickness could enhance the bond strength of steel bar embedded with concrete. By using contact surfaces with cohesive behavior in finite element software, the slip between coated plain steel bar and concrete can be realized. The results of numerical simulation are close to that of experiments, indicating that the model using contact surfaces with cohesive behavior can reasonably predict the results of pullout tests of HPB in concrete.

Finite Element Analysis of X-Cor Sandwich's Compressive Strength

2011 ◽  
Vol 306-307 ◽  
pp. 733-737
Author(s):  
Xu Dan Dang ◽  
Xin Li Wang ◽  
Hong Song Zhang ◽  
Jun Xiao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Failure Modes ◽  
Failure Mechanisms ◽  
Element Model ◽  
Failure Criteria ◽  
Stiffness Degradation ◽  
Element Analysis ◽  
Finite Element Software

In this article the finite element software was used to analyse the values for compressive strength of X-cor sandwich. During the analysis, the failure criteria and materials stiffness degradation rules of failure mechanisms were proposed. The failure processes and failure modes were also clarified. In the finite element model we used the distributions of failure elements to simulate the failure processes. Meanwhile the failure mechanisms of X-cor sandwich were explained. The finite element analysis indicates that the resin regions of Z-pin tips fail firstly and the Z-pins fail secondly. The dominant failure mode is the Z-pin elastic buckling and the propagation paths of failure elements are dispersive. Through contrast the finite element values and test results are consistent well and the error range is -7.6%~9.5%. Therefore the failure criteria and stiffness degradation rules are reasonable and the model can be used to predict the compressive strength of X-cor sandwich.

Integrity Assessment of Subsea Pipeline Dent / Buckle Using ILI Data

2019 ◽  
Author(s):  
Gurumurthy Kagita ◽  
Gudimella G. S. Achary ◽  
Mahesh B. Addala ◽  
Balaji Srinivasan ◽  
Penchala S. K. Pottem ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Failure Modes ◽  
Structural Integrity ◽  
Mechanical Damage ◽  
Metal Loss ◽  
Stress Concentrations ◽  
Subsea Pipeline ◽  
Integrity Assessment ◽  
Finite Element Software

Abstract Mechanical damage in subsea pipelines in the form of local dents / buckles due to excessive bending deformation may severely threaten their structural integrity. A dent / buckle has two significant effects on the pipeline integrity. Notably, residual stresses are set up as result of the plastic deformation and stress concentrations are created due to change in pipe geometry caused by the denting / buckling process. To assess the criticality of a dent / buckle, which often can be associated with strain induced flaws in the highly deformed metal, integrity assessment is required. The objective of this paper is to evaluate the severity of dent / buckle in a 48” subsea pipeline and to make the rerate, repair or replacement decision. This paper presents a Level 3 integrity assessment of a subsea pipeline dent / buckle with metal loss, reported in in-line inspection (ILI), in accordance with Fitness-For-Service Standard API 579-1/ASME FFS-1. In this paper, the deformation process that caused the damage (i.e. dent / buckle) with metal loss is numerically simulated using ILI data in order to determine the magnitude of permanent plastic strain developed and to evaluate the protection against potential failure modes. For numerical simulation, elastic-plastic finite element analyses (FEA) are performed considering the material as well as geometric non-linearity using general purpose finite element software ABAQUS/CAE 2017. Based on the numerical simulation results, the integrity assessment of dented / buckled subsea pipeline segment with metal loss has been performed to assess the fitness-for-service at the operating loads.

scholarly journals Experimental Study and Theoretical Analysis on Flexural Mechanical Propertiesof Reinforced Timber Beams

2018 ◽  
Vol 27 (1) ◽  
pp. 096369351802700
Author(s):  
Xiong Xueyu ◽  
Wang Yiqingzi ◽  
Xue Rongjun ◽  
Lu Xuanxing
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Theoretical Calculations ◽  
Development Trend ◽  
Ultimate Bearing Capacity ◽  
Bending Test ◽  
Element Analysis ◽  
Finite Element Software ◽  
Reinforced Beams

As Chinese architecture masterpiece, ancient Hui-style architecture is the admiration for Chinese and foreign master builders. According to the bending test, the theoretical calculations and Abaqus finite element analysis on 5 Hui-style architecture beams, this paper points out the differences between un-reinforced beams and reinforced beams on ultimate bearing capacity, deflection and other performance indicators. The reinforcement methods of embedding steel bars, embedding CFRP bars and pasting CFRP plate can respectively improve the ultimate bearing capacity by 20.2%, 32.6% and 37.0%. Based on the plane section assumption and considering thereduction of tensile strength causedby wood knots and defects in tension zone, this paper predicts failure modes of the test beams may occur, and gives the ultimate bearing capacity of different failure modes. In addition, this paper uses the Abaqus finite element software for simulating test beams, and the development trend of load-deflectioncurve between the test and numerical simulation are in good agreement, providing reference for further research of Hui-style architecture.

Finite Element Analysis of Dual-Angle Variable of Four Steel Angle Composite Joint with Steel Materials in Civil Engineering

2012 ◽  
Vol 568 ◽  
pp. 125-128
Author(s):  
Yu Zhuo Jia ◽  
Li Zhao
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Transmission Tower ◽  
Node Failure ◽  
Gusset Plate ◽  
Finite Element Software ◽  
Composite Joint ◽  
Steel Angle ◽  
Dual Angle ◽  
Node Design

In the multiple-circuit on same tower UHV and large crossing transmission tower,The main material of towers usually using a composite section in the form of the dual-angle and four steel angle. Dual-angle and four steel angle connections are inevitable. 500KV Jianbi - Danfeng four circuit transmission line project for the background, Using the finite element software ANSYS10.0, Composite Joints three-dimensional nonlinear finite element simulation. Clear the path of force transferor the node, Mechanical behavior of gusset plate and node failure modes. The results show that: node failure modes for the strength failure, The ultimate bearing capacity of the node is about three times the load of the node design, Node design is relatively conservative, By reducing the thickness of the gusset plate to lower node weight.

Thermal Stresses Simulation Analysis of Concrete Box Water Bridge under the Solar Radiation

2011 ◽  
Vol 255-260 ◽  
pp. 952-956
Author(s):  
Jian Ping Sun ◽  
Jian Ping Chen ◽  
Gang Li
Keyword(s):  
Finite Element ◽  
Tensile Strength ◽  
Solar Radiation ◽  
Thermal Stresses ◽  
Simulation Analysis ◽  
Water Bridge ◽  
Finite Element Software ◽  
Steel Bar ◽  
Calculation Results ◽  
The Difference

The reasons why the producing of the difference in temperature distributing and thermal stresses of box aqueduct under solar radiation are analyzed. The difference in temperature distributing and thermal stresses are effectively simulated by the finite element software ANSYS.The calculation results indicate that concrete box aqueduct body inter-surface whatever along the longitudinal and transverse will produce considerable thermal stresses under solar radiation, and its value has exceeded the design of concrete tensile strength. Therefore, the thermal stresses under the solar radiation must be considered in the design of box aqueduct body structural. We should appropriately configure temperature reinforcing steel bar.

scholarly journals PERFORMANCE OF AXIALLY LOADED TAPERED CONCRETE-FILLED STEEL COMPOSITE SLENDER COLUMNS

2013 ◽  
Vol 19 (5) ◽  
pp. 705-717 ◽  
Author(s):  
Alireza Bahrami ◽  
Wan Hamidon Wan Badaruzzaman ◽  
Siti Aminah Osman
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Load Capacity ◽  
Special Kind ◽  
Nonlinear Analyses ◽  
Composite Columns ◽  
Finite Element Software ◽  
Tapered Angle ◽  
Steel Composite ◽  
Slender Columns

This paper focuses on the performance of a special kind of tapered composite columns, namely tapered concrete-filled steel composite (TCFSC) slender columns, under axial loading. These efficient TCFSC columns are formed by the increase of the mid-height depth and width of straight concrete-filled steel composite (CFSC) slender columns, that is, by the enhancement of the tapered angle (from 0° to 2.75°) of the tapered composite columns from their top and bottom to their mid-height. To investigate the performance of the columns, finite element software LUSAS is employed to carry out the nonlinear analyses. Comparisons of the nonlinear finite element results with the existing experimental results uncover the reasonable accuracy of the proposed modelling. Nonlinear analyses are extensively performed and developed to study effects of different variables such as various tapered angles, steel wall thicknesses, concrete compressive strengths, and steel yield stresses on the performance of the columns. It is concluded that increasing each of these variables considerably enhances the ultimate axial load capacity. Also, enhancement of the tapered angle and/or steel wall thickness significantly improves the ductility. Moreover, confinement effect of the steel wall on the performance of the columns is evaluated. Failure modes of the columns are also presented.

Buckling Behaviour of Circular Ring Stiffened Filament Wound Composite Pressure Hull through Finite Element Analysis

2014 ◽  
Vol 656 ◽  
pp. 288-297
Author(s):  
Krishna Murari Pandey ◽  
Abhijit Dey ◽  
P.L. Choudhury
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Pressure Vessel ◽  
Failure Modes ◽  
Element Analysis ◽  
Finite Element Software ◽  
Filament Wound ◽  
Composite Pressure Vessel ◽  
Filament Wound Composite ◽  
Wound Composite

The aim of present study was investigate the buckling pressure of moderately thick-walled filament-wound carbon–epoxy stiffened composite pressure vessel subjected to external hydrostatic pressure through finite element analysis and compare the result with un-stiffened filament wound carbon/epoxy composite pressure vessel used in under water vehicle applications. The winding angles were [±30/90] FW, [±45/90] FW and [±60/90] FW. ANSYS 14.0 APDL, a commercial finite element software package successfully predicted the buckling pressure of filament-wound composite pressure vessel with a deviation much higher than the results of un-stiffened filament wound composite cylinder .All the finite element analysis shows that the composite pressure vessel with winding pattern [±60/90] FW has the higher value of critical buckling pressure. Major failure modes in both the analysis were dominated by the helical winding angles.

scholarly journals Modeling the Bond Stress at Steel-Concrete Interface for Uncorroded and Corroded Reinforcing Steel

2021 ◽  
Author(s):  
Alaka Ghosh
Keyword(s):  
Finite Element ◽  
Bond Strength ◽  
Mass Loss ◽  
Fe Analysis ◽  
Nonlinear Finite Element ◽  
Reinforcing Steel ◽  
Sectional Area ◽  
Cross Sectional ◽  
Pullout Tests ◽  
Concrete Interface

Corrosion of reinforcing steel causes cracking and spalling of concrete structures, reduces the effective cross-sectional area of the reinforcing steel and the concrete simultaneously decreases the bond strength at the steel-concrete interface. The detrimental effect of corrosion on the service life of reinforced concrete structures highlights the need for modeling of bond strength between the corroded steel and the concrete. This research presents a nonlinear finite element model for the bond stress at the steel-concrete interface for both uncorroded and corroded reinforcing steel. The nonlinear finite element program ABAQUS is used for this purpose. The expanded volume of corroded product of reinforcing steel produces radial and hoop stresses which cause longitudinal cracks in the concrete. The increased longitudinal crack width, the loss of effective cross-sectional area of the steel and the concrete is also reduced due to the lubricating effect of flaky corroded layer. This research models the loss of contact pressure and the decrease of friction coefficient with the mass loss of the reinforcing steel. The model analyzes the pullout tests of Amleh (2002) and a good agreement is noted between the analytical and the experimental results. Both in FE analysis and experimental results, the loss of bond capacity is almost linear with mass loss of rebar. FE analysis and experiemental result show that, up to 5% mass loss, the bond capacity loss is moderate, at 10 to 15% mass loss, significant amount of bond capacity is lost and at about 20% mass almost all bond capacity is lost. The model is also validated by analyzing the pullout tests performed by Cabrera and Ghoddoussis (1992) and those by Al-Sulaimani et al.(1990).

scholarly journals Modeling the Bond Stress at Steel-Concrete Interface for Uncorroded and Corroded Reinforcing Steel

2021 ◽  
Author(s):  
Alaka Ghosh
Keyword(s):  
Finite Element ◽  
Bond Strength ◽  
Mass Loss ◽  
Fe Analysis ◽  
Nonlinear Finite Element ◽  
Reinforcing Steel ◽  
Sectional Area ◽  
Cross Sectional ◽  
Pullout Tests ◽  
Concrete Interface

Corrosion of reinforcing steel causes cracking and spalling of concrete structures, reduces the effective cross-sectional area of the reinforcing steel and the concrete simultaneously decreases the bond strength at the steel-concrete interface. The detrimental effect of corrosion on the service life of reinforced concrete structures highlights the need for modeling of bond strength between the corroded steel and the concrete. This research presents a nonlinear finite element model for the bond stress at the steel-concrete interface for both uncorroded and corroded reinforcing steel. The nonlinear finite element program ABAQUS is used for this purpose. The expanded volume of corroded product of reinforcing steel produces radial and hoop stresses which cause longitudinal cracks in the concrete. The increased longitudinal crack width, the loss of effective cross-sectional area of the steel and the concrete is also reduced due to the lubricating effect of flaky corroded layer. This research models the loss of contact pressure and the decrease of friction coefficient with the mass loss of the reinforcing steel. The model analyzes the pullout tests of Amleh (2002) and a good agreement is noted between the analytical and the experimental results. Both in FE analysis and experimental results, the loss of bond capacity is almost linear with mass loss of rebar. FE analysis and experiemental result show that, up to 5% mass loss, the bond capacity loss is moderate, at 10 to 15% mass loss, significant amount of bond capacity is lost and at about 20% mass almost all bond capacity is lost. The model is also validated by analyzing the pullout tests performed by Cabrera and Ghoddoussis (1992) and those by Al-Sulaimani et al.(1990).

scholarly journals Experimental and Finite Element Research on the Failure Mechanism of C/C Composite Joint Structures under Out-of-Plane Loading

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2922
Author(s):  
Yanfeng Zhang ◽  
Zhengong Zhou ◽  
Zhiyong Tan
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Displacement Curve ◽  
Finite Element Software ◽  
Pull Out ◽  
Composite Joint ◽  
Element Simulation ◽  
Out Of Plane ◽  
The Matrix ◽  
Failure Morphology

The loading and the failure mode of metal hexagon bolt joints and metal counter-sunk bolt joints of C/C composites were investigated. The joints were tested for out-of-plane loading at two temperatures (600 °C and 800 °C). The failure morphology of a lap plate was investigated, and the main failure modes were determined. The typical load–displacement curve was characterized and the test was simulated using ABAQUS non-linear finite element software. Furthermore, progressive damage was induced, and comparison of the finite element simulation with the experimental data revealed that the failures mainly occurred in the lower lap plate and were dominated by cracking and delamination of the matrix, accompanied by the pull-out of a small number of piercing fibers. Finally, the influences of the temperature, nut radius, and fixture geometry on the critical load were determined via simulation.

Sign in / Sign up

Export Citation Format

Share Document