scholarly journals Effect of Finishing and Polishing on The Surface Roughness of Bulk Fill Composites

2021 ◽  
Vol 15 (1) ◽  
pp. 25-32
Author(s):  
Abdullah Aljamhan ◽  
Syed Rashid Habib ◽  
Mohammed A. AlSarhan ◽  
Bashayer AlZahrani ◽  
Hessa AlOtaibi ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Statistical Analysis ◽  
Composite Materials ◽  
Composite Resins ◽  
Group Iii ◽  
Significant Difference ◽  
Optical Profilometer ◽  
Test Materials

Objective: The aim of this in vitro study was to compare the effect of three finishing/polishing systems on the surface roughness (Ra) of conventional and Bulk-fill composite resins. Materials and methods: The Ra values of three different brands of Bulk-fill composites (Filtek Bulk-fill®, 3M ESPE; SonicFill Bulk-fill®, Kerr; SDR Bulk-fill®, Dentsply) were tested and compared with the Ra of a conventional composite (Filtek XT Z350®, 3M ESPE). A total of 30 discs (10 mm × 2 mm) were fabricated from four test materials and divided into three groups (n = 10/group) depending on the three finishing/polishing systems used (Astropol®, Ivoclar Vivadent; PoGo®, Dentsply; Sof-LexTM®, 3M ESPE). The Ra of each specimen was recorded with an optical profilometer (Contour-GT-X®, USA). ANOVA and Tukey’s tests were used for statistical analysis. Results: Statistically significant differences (P < 0.05) were observed between the Ra values of all composite materials tested with three finishing/polishing systems. Among composite materials, only Group-III showed a significant difference (P = 0.003) in Ra obtained using all three finishing/polishing systems. SDR Bulk-fill® and Filtek XT Z350® showed the highest (0.810 ± 0.373 µm) and lowest (0.365 ± 0.119 µm) Ra values, respectively. Individually, the highest Ra was recorded for SDR Bulk-fill® when it was finished/polished with the Astropol® system. SonicFill Bulk-fill® and SDR Bulk-fill® composites exhibited the lowest Ra values when they were finished with the PoGo® system. Conclusion: Finishing and polishing techniques greatly affect the surface roughness of different Bulk-fill composites because variations in the surface roughness were observed for all tested composite materials. Filtek XT Z350® exhibited the lowest surface roughness, while SDR Bulk-fill® exhibited the highest surface roughness among the tested composite materials.

Influence of Polishing Systems on Surface Roughness of Composite Resins: Polishability of Composite Resins

2019 ◽  
Vol 44 (3) ◽  
pp. E122-E132 ◽  
Author(s):  
L St-Pierre ◽  
C Martel ◽  
H Crépeau ◽  
MA Vargas
Keyword(s):  
Surface Roughness ◽  
In Vitro Study ◽  
Threshold Value ◽  
Lower Surface ◽  
Composite Resins ◽  
Initial Surface ◽  
Final Surface ◽  
Significant Difference ◽  
One Step

SUMMARY Objectives: The objective of this in vitro study was to compare, with a threshold value of 200 nm, the surface roughness obtained when using 12 different polishing systems on four different composite resins (microfill, nanofill, and two nanohybrids). Methods and Materials: A total of 384 convex specimens were made using Durafill VS, Filtek Supreme Ultra, Grandio SO, and Venus Pearl. After sandblasting and finishing with a medium-grit finishing disc, initial surface roughness was measured using a surface roughness tester. Specimens were polished using 12 different polishing systems: Astropol, HiLuster Plus, D♦Fine, Diacomp, ET Illustra, Sof-Lex Wheels, Sof-Lex XT discs, Super-Snap, Enhance/Pogo, Optrapol, OneGloss and ComposiPro Brush (n=8). The final surface roughness was measured, and data were analyzed using two-way analysis of variance. Pairwise comparisons were made using protected Fisher least significant difference. Results: There were statistical differences in the final surface roughness between polishing systems and between composite resins (p&lt;0.05). The highest surface roughness was observed for all composite resins polished with OneGloss and ComposiPro Brush. Enhance/Pogo and Sof-Lex Wheels produced a mean surface roughness greater than the 200-nm threshold on Filtek Supreme Ultra, Grandio SO, and Venus Pearl. Data showed that there was an interaction between the composite resins and the polishing systems. Conclusions: A single polishing system does not perform equally with all composite resins. Except for Optrapol, multi-step polishing systems performed generally better than one-step systems. Excluding Enhance/Pogo, diamond-impregnated polishers led to lower surface roughness. Durafill VS, a microfill composite resin, may be polished more predictably with different polishers.

scholarly journals Press-On Force Effect on the Efficiency of Composite Restorations Final Polishing—Preliminary In Vitro Study

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 705
Author(s):  
Anna Lehmann ◽  
Kacper Nijakowski ◽  
Natalia Potempa ◽  
Paweł Sieradzki ◽  
Mateusz Król ◽  
...  
Keyword(s):  
Surface Roughness ◽  
In Vitro Study ◽  
Composite Resins ◽  
Major Influence ◽  
Composite Surface ◽  
Significance Level ◽  
Subsequent Step ◽  
Optical Profilometer ◽  
Applied Forces

The surface texture of dental restorations has a major influence on plaque accumulation and aesthetical appearance. The study aimed to evaluate the surface roughness of composite resins depending on the varying polishing sequences and applied forces. A total of 60 samples from two composite resins (Boston and Charisma) were polymerized using a lamp with 1200 mW/cm2 intensity and covering celluloid strip. The polishing sequence consisted of 12.6 mm OptiDisc (Kerr) – with increased disc per each subsequent step. Half of the samples were polished at 1N force, with the other half at 2N. The surface roughness examination was performed using a WYKO NT930 (Veeco) optical profilometer. The selected roughness parameters were compared by ANOVA with the significance level α = 0.05. The more complex polishing sequence affected on the composite smoothness. Higher roughness was identified in Charisma samples as compared to Boston. The specimens polished with 2N force contained a slightly rougher surface than those polished with 1N. However, these differences were not statistically significant. Despite the satisfactory visual effect obtained by polishing the composite samples, the profilometric examination revealed the roughness. Finishing is crucial for providing a smooth composite surface, allowing it to function properly in the oral environment.

scholarly journals Influence of different polishing and aging periods on the surface roughness of composite resins

2021 ◽  
Vol 10 (4) ◽  
pp. e27310414305
Author(s):  
Ricardo Coelho Okida ◽  
Isis Almela Endo Hoshino ◽  
Lívia Patrícia Romanini ◽  
Amanda Maslen Fontes ◽  
Lara Maria Bueno Esteves ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Artificial Aging ◽  
Statistical Tests ◽  
In Vitro Study ◽  
Constant Load ◽  
Composite Resins ◽  
Repeated Testing ◽  
Significant Difference ◽  
Before And After

The aim of this study was to evaluate the influence of the polishing period on surface roughness (Ra) before and after thermal aging in four composite resins - CR (Durafill VS, Vittra APS, Filtek Z350XT and Spectra Smart). This in vitro study evaluated: (1) CR in 4 levels; (2) polishing period (PP) in three levels (immediate, 7 and 14 days) and (3) artificial aging in two levels: without aging and after 10,000 cycles. For this, 240 CR specimens were allocated into 12 groups (n=20) according to PP with SofLex Pop On disks.  For Ra, 3 measurements on the top surface of each specimen were performed with a diamond tip and constant load of 4mN and 0.25mm/s. Next, the specimens were aged in thermocycling, with temperatures of 5° and 55°C, during 30 seconds in each temperature, and repeated testing afterwards. The data were submitted to statistical tests with 5% significance. The alteration in Ra was observed only in the late polishing in the period of 7 days, where the Durafill VS CR showed higher Ra in comparison to the other CRs. After thermocycling, the groups showed significant difference only with late polishing in the 21-day period; the nanoparticulated RCs (Z350XT˂Vittra APS) recorded the highest Ra values, followed by the microhybrid (DurafillVS) and nanohybrid (Spectra Smart) RCs, respectively. Thus, late polishing in the 7-day and immediate period provided higher Ra values, especially for the nanohybrid and microhybrid composite resins.

scholarly journals Antifungal Activity of Denture Base Resin Containing Nanozirconia: In Vitro Assessment of Candida albicans Biofilm

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Reem Abualsaud ◽  
Doaa M. Aleraky ◽  
Sultan Akhtar ◽  
Soban Q. Khan ◽  
Mohammed M. Gad
Keyword(s):  
Surface Roughness ◽  
Direct Method ◽  
Acrylic Resin ◽  
Denture Base ◽  
Significant Difference ◽  
Base Resin ◽  
Optical Profilometer ◽  
Agar Media ◽  
Post Hoc

Objective. To evaluate the antimicrobial effects of different concentrations of zirconium dioxide nanoparticles (nano-ZrO2) reinforcement of poly(methyl) methacrylate (PMMA) on surface roughness and C. albicans biofilm. Methods. 20 heat-polymerized acrylic resin discs were conventionally made and divided into 4 groups (n = 5) according to nano-ZrO2 concentration: control (0% filler) and 3 experimental groups (2.5% (Z2.5), 5.0% (Z5.0), and 7.5% (Z7.5)). An optical profilometer was used for surface roughness evaluation, followed by Candida adherence assay. Specimens were sterilized, then immersed in cultured yeast (C. albicans), and incubated at 37°C for 48 hours. After that, discs were rinsed before extracting the clustered pellets of Candida. The attached C. albicans was counted using the direct method after spreading on agar media and incubating for 48 hours. Statistical analysis was performed using one-way ANOVA and Tukey’s post hoc test at α = 0.05. Results. Surface roughness was significantly increased with all modified groups compared with control ( P < 0.01 ), which showed the lowest roughness value (0.027 ± 0.004 μm). There was no significant difference in the roughness value among reinforced groups (2.5, 5.0, and 7.5%) ( P > 0.05 ), with Z7.5 showing the highest roughness value (0.042 ± 0.004 μm). Candida count was reduced as the nano-ZrO2 increased but not significantly ( P = 0.15 ). Conclusions. The addition of different concentrations of nano-ZrO2 particles to PMMA increased the surface roughness compared with control; in contrast, insignificant reduction of C. albicans biofilm was detected.

scholarly journals Quantitative evaluation of the progressive wear of powered interproximal reduction systems after repeated use

2019 ◽  
Vol 81 (1) ◽  
pp. 22-29
Author(s):  
C. Livas ◽  
T. Baumann ◽  
S. Flury ◽  
N. Pandis
Keyword(s):  
Surface Roughness ◽  
Surface Profile ◽  
Average Decrease ◽  
Grain Sizes ◽  
Significant Difference ◽  
Unit Increase ◽  
Optical Profilometer ◽  
Repeated Applications ◽  
Diamond Grain

Abstract Purpose To evaluate the residual surface roughness of 5 common diamond-coated interproximal reduction (IPR) systems after consecutive in vitro applications in relation to system, diamond grain size, and instrument thickness. Methods IPR was performed on 80 extracted human incisors using motor-driven strips and discs under predefined conditions. The IPR auxiliaries were applied at 5 consecutive sessions of 20 s on intact interproximal surfaces, and the surface profile (Ra, Rz, Rmax) was analyzed at baseline and after each session with an optical profilometer. Results No overall significant difference in the roughness values was found between systems (P = 0.07 for Ra, P = 0.33 for Rz, and P = 0.48 for Rmax). There was a significant average decrease of Ra, Rz, and Rmax for all systems for every unit increase in time by −0.171 μm (P < 0.001), −3.297 (P ≤ 0.001), and −2.788 μm (P = 0.001), respectively. Ra, Rz, and Rmax values increased significantly, i.e., by 0.194 μm (P = 0.003), 5.890 μm (P = 0.001), and 5.319 μm (P = 0.010) as instrument thickness increased by one unit. No significant reductions in Ra, Rz, and Rmax were observed across grain sizes (−0.008 μm [P > 0.05], −0.244 μm [P > 0.05], and −0.179 μm [P > 0.05], respectively). There was no evidence of interaction between system and time as the P values for Ra, Rz, and Rmax were 0.88, 0.51, and 0.70, respectively. Conclusions All IPR materials presented significant gradual decrease of surface roughness after repeated applications. There were no significant roughness changes among auxiliaries of different grain sizes. Thinner auxiliaries showed significantly more roughness reduction, possibly requiring more frequent replacement than thick auxiliaries in clinical practice.

Surface properties of composite resins with and without fluorides for bracket bonding / Propriedades de superfície de resinas compostas com e sem fluoretos para colagem de suportes

2021 ◽  
Vol 7 (7) ◽  
pp. 67267-67276
Author(s):  
Emillyn Jones Greijal Dias Holanda ◽  
José Guilherme Neves ◽  
Milton Santamaria-Jr ◽  
Silvia Amélia Scudeler Vedovello ◽  
Ana Rosa Costa ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Color Change ◽  
Composite Resins ◽  
Hardness Tester ◽  
Significant Difference ◽  
Post Test ◽  
Roughness Analysis ◽  
Diamond Paste ◽  
Penetration Time

The aim of this study was to evaluate the surface properties of orthodontic resins with and without fluoride. Forty disks, measuring 2 mm thick by 6 mm in diameter, were made of 4 bracket-bonding composite resins (n=10): Transbond Plus Color Change-3M/Unitek (TPCC); Transbond XT- 3M/Unitek (TXT), Orthocem -FGM (OC); Orthocem UV Trace-FGM (OCUV). The discs were photoactivated for 40 seconds with irradiance of 450 mW/cm2 and manually polished in sequence by silicon carbide sandpapers with 1200 and 2000 grain size and finished with diamond paste and felt disc. The surface microhardness analysis was performed using a Shimadzu Micro Hardness Tester HMV-2,000 (Shimadzu Corporation, Kyoto, Japan) with a load of 50 gF and a 5 second penetration time. Surface roughness readings were taken using a Surf Corder Roughness Meter (SE 1700- Kosaka, Lisboa-Portugal). For data analysis, ANOVA (one-way) was used, followed by Tukey's post-test (?=0.05). The microhardness results showed a difference (p?0.05) in the means of the orthodontic resins between TPCC and TXT with the other groups. After the surface roughness analysis, the averages showed that TPCC resin showed higher roughness compared to OC and OCUV (p?0.05), and there was no statistical difference with TXT. It was concluded that statistically the composite resins with fluoride showed significant difference regarding hardness and roughness.

scholarly journals In vitro quantitative evaluation of marginal microleakage in class II restorations confected with a glass ionomer cement and two composite resins

2001 ◽  
Vol 15 (4) ◽  
pp. 277-282 ◽  
Author(s):  
Maria Fernanda Borro BIJELLA ◽  
Maria Francisca Thereza Borro BIJELLA ◽  
Salete Moura Bonifácio da SILVA
Keyword(s):  
Glass Ionomer Cement ◽  
Class Ii ◽  
Deionized Water ◽  
Composite Resins ◽  
Glass Ionomer ◽  
Dye Penetration ◽  
Significant Difference ◽  
Distal Direction ◽  
Ionomer Cement

This study evaluated, in vitro, marginal microleakage in class II restorations confected with the glass ionomer cement Vitremer and with the composite resins Ariston pHc and P-60. The aims of the study were to assess the effect of thermocycling on those materials and to evaluate two methods utilized in the analysis of dye penetration. Sixty premolars divided in three groups were utilized; the teeth had proximal cavities whose cervical walls were located 1 mm below the cementoenamel junction. Half of the test specimens from each group underwent thermocycling; the other half remained in deionized water, at 37ºC. The specimens were immersed, for 24 hours, in a basic 0.5% fuchsin solution at 37ºC. For the analysis of microleakage, the specimens were sectioned in a mesio-distal direction, and the observation was carried out with the software Imagetools. The results were evaluated through the 2-way ANOVA and through the Tukey’s test. All groups presented marginal microleakage. The smallest values were obtained with Vitremer, followed by those obtained with the composite resins P-60 and Ariston pHc. There was no statistically significant difference caused by thermocycling, and the method of maximum infiltration was the best for detecting the extension of microleakage.

scholarly journals Effect of an Optical Whitening Toothpaste on Color Stability of Tooth-Colored Restorative Materials

2020 ◽  
Vol 14 (01) ◽  
pp. 085-091
Author(s):  
Sedighe Sadat Hashemikamangar ◽  
Farnoosh Hoseinpour ◽  
Nazanin Kiomarsi ◽  
Mehrzad Gholampour Dehaki ◽  
Mohammad Javad Kharazifard
Keyword(s):  
Statistical Analysis ◽  
Color Change ◽  
Color Stability ◽  
Composite Resins ◽  
Time Points ◽  
Color Changes ◽  
Honestly Significant Difference ◽  
Significant Difference ◽  
Resin Modified Glass Ionomer ◽  
Composite Samples

Abstract Objectives This study aimed to assess the effect of an optical whitening toothpaste on color stability of microhybrid, nanofilled, and microfilled composite resins and resin-modified glass ionomer (RMGI) cement in comparison of two other toothpastes. Materials and Methods In this experimental study, disc-shaped composite samples were fabricated. The samples were then polished using silicon carbide papers. Twenty-seven samples of each material were fabricated and subjected to colorimetry using a spectrophotometer. Each group of material was then divided into three subgroups for the application of conventional whitening and whitening containing blue covarine toothpastes. One operator brushed the samples with an electric soft toothbrush with circular motion twice a day, each time for 30 seconds. Colorimetry was performed at 0, 1, 7, 30, and 90 days. Statistical Analysis Two-way analysis of variance (ANOVA), one-way ANOVA, and Tukey’s honestly significant difference (HSD) test were used for statistical analysis. Results The interaction effect of type of restorative material and time on ∆E was not significant at baseline or 1 day (p > 0.05). The effect of type of toothpaste on ∆E was not significant at baseline or 1 day (p = 0.78) but the effect of type of material was significant (p < 0.05). The toothpastes had significantly different effects on ∆E of Z250 at all time points (p < 0.05) except for ∆E0–30 (p = 0.106). The toothpastes had significantly different effects on ∆E of Z350 and Gradia at all time points (p < 0.05). The same was true for RMGI except for ∆E0–7 (p = 0.43) and ∆E0–90 (p = 0.52). The majority of color changes caused by toothpastes were not clinically perceivable (∆E < 3.3), except for ∆E0–90 by the whitening toothpaste (∆E = 9), ∆E0–90 by the conventional toothpaste for Z350 (∆E = 3.9), and ∆E0–1 by the whitening toothpaste for RMGI (∆E = 3.7). Conclusion The color change of all composite samples was not clinically perceivable (<3.3) at all time points, which shows that the tested toothpastes do not cause a significant change in color of composite materials.

scholarly journals Results of modern tuboperitoneal infertility treatment

2009 ◽  
Vol 66 (1) ◽  
pp. 57-62 ◽  
Author(s):  
Drenka Turjacanin-Pantelic ◽  
Dragana Bojovic-Jovic ◽  
Biljana Arsic ◽  
Eliana Garalejic
Keyword(s):  
Statistical Analysis ◽  
Surgical Treatment ◽  
Infertility Treatment ◽  
P Value ◽  
Modern Approach ◽  
Vitro Fertilization ◽  
Group I ◽  
Significant Difference ◽  
Group Ii

Background/Aim. A modern approach to surgical treatment of tuboperitoneal infertility is based on laporascopic techniques. The aim of this study was to compare results of tuboperitoneal infertility treatment by the use of laparoscopy and classical laparotomy. Methods. A retrospectiveprospective study on 66 women treated operatively form tuboperitoneal infertility was performed. Data from patient's anamnesis and those related to the surgical treatment results, obtained by the use of an inquiry, were used in retrospective and prospective analysis, respectively. Chi-square test was used in statistical analysis. P value < 0.05 was considered significant. Results. Classical laparotomy was used on 34 women in a period from 1996 to 1997, while 32 women were operated laparoscopically in a period from 1999 to 2000. The results were as follows: a total number of conceived women was 16 (24%), seven in the group I (20.6%) and nine in the group II (28.1%); 13 women were with one pregnancy, six in the group I (17.6%) and seven in the group II (22%). Twice pregnant were three women, one in the group I (2.9%) and two in the group II (6.2%). The resulting pregnancies were: five women with abortion spontaneous, two in the group I (5.9%) and three in the group II (9.4%); two women with extrauterine pregnancy in the group I (5.9%); three with pretemporal birth, one in the group I (2.9%) and two in the group II (6.2%), while six women were with the temporal birth, two in the group I (5.9%) and four in the group II (12.5%). Statistical analysis showed that there was no significant difference in the results between these two groups. Conclusion. Surgical treatment of tubeperitoneal infertility, regardless of the used methods (classical laparotomy or laparoscopy) was successful in a great number of women. These methods have a great advantage over in vitro fertilization, and they should not be ignored.

scholarly journals Comparison of Shear Bond Strength and Microleakage of Various Bulk-fill Bioactive Dentin substitutes: An in vitro Study

2016 ◽  
Vol 17 (12) ◽  
pp. 997-1002 ◽  
Author(s):  
Fahad I Alkhudhairy ◽  
Zeeshan H Ahmad
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Physical And Mechanical Properties ◽  
Pairwise Comparison ◽  
In Vitro Study ◽  
Composite Resins ◽  
Intergroup Comparison ◽  
Significant Difference ◽  
Tukey Honestly Significant Difference

ABSTRACT Introduction Various bulk-fill materials depending on their composition, viscosity, and flow ability have different physical and mechanical properties. The aim of this in vitro study was to determine and compare the shear bond strength and microleakage properties of activa restorative with other bulk-fill restorative materials surefil (SDR), Biodentine, ever X posterior. Materials and methods Forty permanent premolars were selected for shear bond strength, and 20 permanent premolars were selected with class II cavities on mesial and distal side for microleakage. Universal testing device was used to assess the shear bond strength. Microleakage was checked using dye penetration method under a stereomicroscope. Mean and standard deviation values were calculated from the recorded values. Intergroup comparison was done by one-way analysis of variance (ANOVA) followed by pairwise comparison using Tukey honestly significant difference (HSD) post hoc test. Results The mean shear bond strength was highest for SDR surefil followed by Ever X posterior, Bioactive restorative, and Biodentine respectively. In this study, SDR (surefil) showed better shear bond strength and better microleakage properties compared with the other test materials (F = 186.7157, p < 0.05). Conclusion The result of this study showed that flowable and fiber-reinforced composites have better shear bond strength and microleakage properties. Clinical significance Flowable bulk-fill composite resins can be used as dentin substitutes because of its superior properties. How to cite this article Alkhudhairy FI, Ahmad ZH. Comparison of Shear Bond Strength and Microleakage of Various Bulk-fill Bioactive Dentin substitutes: An in vitro study. J Contemp Dent Pract 2016;17(12):997-1002.

Sign in / Sign up

Export Citation Format

Share Document