scholarly journals Experimental study of the mechanical properties of Palacos bone cements

TRAUMA ◽  
2021 ◽  
Vol 22 (3) ◽  
pp. 63-67
Author(s):  
P.M. Zhuk ◽  
M.N. Matsipura ◽  
V.O. Movchaniuk ◽  
M.Yu. Karpinskiy ◽  
O.D. Karpinska ◽  
...  
Keyword(s):  
Mathematical Modeling ◽  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Bone Cement ◽  
Ultimate Strength ◽  
Polymerization Process ◽  
Bone Cements ◽  
Fast Bone

Background. Currently, bone cements are widely used in orthopedics. The range of prescriptions for bone cement use is very large, and requires different qualities depending on the purpose. Therefore, researchers are forced to conduct their own invetigations to study the mechanical properties of bone cements. The purpose was to determine in the experiment the value of an elastic modulus and ultimate strength of Palacos bone cements for further use in mathematical models of osteosynthesis and arthroplasty. Materials and methods. Samples of two brands of cement, Palacos R and Palacos fast, were examined. Samples with a diameter of 5 mm and a length of 10 mm were made from each type of cement. The study was carried out 2 hours and 2 days after polymerization. At each stage, 10 cement samples of each type were tested for compression. Results. After 2 hours of polymerization, the Palacos fast samples had a statistically significant advantage in terms of the tensile strength, which was 105.77 ± 3.19 MPa, over the Palacos R — 87.24 ± 3.70 MPa. The higher elastic modulus for Palacos fast samples — 2,942.50 ± 99.67 MPa compared to Palacos R — 82,542.40 ± 65.55 MPa turned out to be statistically significant. Two days after fabrication, the strength characteristics of bone cements changed upward. Thus, the ultimate strength of Palacos fast samples was determined within 116.39 ± 2.85 MPa, which is statistically significant higher than for Palacos R samples for which this indicator was within 95.58 ± 4.53 MPa. Similar tendencies were characteristic of an elastic modulus, which amounted to 3,048.93 ± 108.70 MPa for Palacos fast and 2,642.90 ± 22.93 MPa — for Palacos R samples. The value of the elastic modulus for both brands of bone cement has a statistically significant tendency to increase. On average, an elastic modulus for Palacos R cement increased by 4.0 ± 2.6 %, for Palacos fast samples — by 3.5 ± 1.4 %. Conclusions. Palacos R bone cement by the end of the polymerization process has an elastic modulus of 2,542.40 ± 65.55 MPa and a tensile strength of 87.24 ± 3.70 MPa, which is statistically significant lower (p = 0.001) than thereof Palacos fast cement (2,942.50 ± ± 99.67 MPa and 105.77 ± 3.19 MPa, respectively). The indicators of the tensile strength and elastic modulus of the samples of bone cement of both studied brands have a statistically significant (p = 0.001) tendency to increase within 2 days, on average by 9.6 ± 10.1 % and 3.5 ± 4.0 %, respectively. The obtained elastic modulus and ultimate strength of Palacos R and Palacos fast bone cements can be used for mathematical modeling of various types of arthroplasty.

Molecular dynamics study on the tensile properties of graphene/Cu nanocomposite

2017 ◽  
Vol 06 (03) ◽  
pp. 1750021 ◽  
Author(s):  
Jun Hua ◽  
Zhirong Duan ◽  
Chen Song ◽  
Qinlong Liu
Keyword(s):  
Mechanical Properties ◽  
Molecular Dynamics ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Comparative Analysis ◽  
Strain Rate ◽  
Ultimate Strength ◽  
Strain Rates ◽  
Single Crystal Copper ◽  
Single Slice

In this paper, the mechanical properties, including elastic properties, deformation mechanism, dislocation formation and crack propagation of graphene/Cu (G/Cu) nanocomposite under uniaxial tension are studied by molecular dynamics (MD) method and the strain rate dependence is also investigated. Firstly, through the comparative analysis of tensile results of single crystal copper (Cu), single slice graphene/Cu (SSG/Cu) nanocomposite and double slice graphene/Cu (DSG/Cu) nanocomposite, it is found that the G/Cu nanocomposites have larger initial equivalent elastic modulus and tensile ultimate strength comparing with Cu and the more content of graphene, the greater the tensile strength of composites. Afterwards, by analyzing the tensile results of SSG/Cu nanocomposite under different strain rates, we find that the tensile ultimate strength of SSG/Cu nanocomposite increases with the increasing of strain rate gradually, but the initial equivalent elastic modulus basically remains unchanged.

Experimental Study on Basic Mechanical Properties of Recycled Concrete Made of Brick and Tile

2012 ◽  
Vol 166-169 ◽  
pp. 3323-3328
Author(s):  
Ling Jun Xie ◽  
Ai Liang Zhai ◽  
Chun He Wang ◽  
Chang Liang Ji ◽  
Shu Jian Chen
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Failure Modes ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Brick And Tile

By experimental, study on the elastic modulus including the failure modes of Recycled Concrete made of Brick and Tile with the splitting tensile strength and the compressive strength, And the relational formula between the splitting tensile strength and the compressive strength was summarized from the results.

Effect of Clay Dosage on Mechanical Properties of Plastic Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 664-667 ◽  
Author(s):  
Qiao Yan Guan ◽  
Peng Zhang
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Internal Friction ◽  
Friction Angle ◽  
Splitting Tensile Strength ◽  
Plastic Concrete

A designed experimental study has been conducted to investigate the effect of clay dosage on mechanical properties of plastic concrete. The mechanical properties include compressive strength, splitting tensile strength, shear strength and elastic modulus. On the basis of the experimental results of the specimens of eight sets of mix proportions, the mechanism of action of clay on these mechanical properties has been analyzed in details. The results indicate that there is a tendency of decrease in the compressive strength, splitting tensile strength, shear strength and elastic modulus of plastic concrete with the increase of clay dosage. However, the internal friction angle of the shear specimens is increasing gradually with the increase of clay dosage. Further, the clay appears can improve the ductility of plastic concrete and this can help plastic concrete to bear larger deformation before failure.

scholarly journals Influence of Alumina Nanofibers Sintered by the Spark Plasma Method on Nickel Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 548 ◽  
Author(s):  
Leonid Agureev ◽  
Valeriy Kostikov ◽  
Zhanna Eremeeva ◽  
Svetlana Savushkina ◽  
Boris Ivanov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Strength Properties ◽  
Alumina Nanoparticles ◽  
Metal Powders ◽  
Wide Range ◽  
The Matrix ◽  
Spark Plasma ◽  
Average Size

The article presents the study of alumina nanoparticles’ (nanofibers) concentration effect on the strength properties of pure nickel. The samples were obtained by spark plasma sintering of previously mechanically activated metal powders. The dependence of the grain size and the relative density of compacts on the number of nanofibers was investigated. It was found that with an increase in the concentration of nanofibers, the average size of the matrix particles decreased. The effects of the nanoparticle concentration (0.01–0.1 wt.%) on the elastic modulus and tensile strength were determined for materials at 25 °C, 400 °C, and 750 °C. It was shown that with an increase in the concentration of nanofibers, a 10–40% increase in the elastic modulus and ultimate tensile strength occurred. A comparison of the mechanical properties of nickel in a wide range of temperatures, obtained in this work with materials made by various technologies, is carried out. A description of nanofibers’ mechanisms of influence on the structure and mechanical properties of nickel is given. The possible impact of impurity phases on the properties of nickel is estimated. The tendency of changes in the mechanical properties of nickel, depending on the concentration of nanofibers, is shown.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

The influence of functionalization time of carbon nanotube on the mechanical properties of the epoxy composites

2017 ◽  
Vol 51 (12) ◽  
pp. 1693-1701 ◽  
Author(s):  
EA Zakharychev ◽  
EN Razov ◽  
Yu D Semchikov ◽  
NS Zakharycheva ◽  
MA Kabina
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Carbon Nanotube ◽  
Composite Materials ◽  
Polymer Composites ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

This paper investigates the structure, length, and percentage of functional groups of multi-walled carbon nanotubes (CNT) depending on the time taken for functionalization in HNO3 and H2SO4 mixture. The carbon nanotube content and influence of functionalization time on mechanical properties of polymer composite materials based on epoxy matrix are studied. The extreme dependencies of mechanical properties of carbon nanotube functionalization time of polymer composites were established. The rise in tensile strength of obtained composites reaches 102% and elastic modulus reaches 227% as compared to that of unfilled polymer. The composites exhibited best mechanical properties by including carbon nanotube with 0.5 h functionalization time.

Sign in / Sign up

Export Citation Format

Share Document