scholarly journals Influence of Alumina Nanofibers Sintered by the Spark Plasma Method on Nickel Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 548 ◽  
Author(s):  
Leonid Agureev ◽  
Valeriy Kostikov ◽  
Zhanna Eremeeva ◽  
Svetlana Savushkina ◽  
Boris Ivanov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Strength Properties ◽  
Alumina Nanoparticles ◽  
Metal Powders ◽  
Wide Range ◽  
The Matrix ◽  
Spark Plasma ◽  
Average Size

The article presents the study of alumina nanoparticles’ (nanofibers) concentration effect on the strength properties of pure nickel. The samples were obtained by spark plasma sintering of previously mechanically activated metal powders. The dependence of the grain size and the relative density of compacts on the number of nanofibers was investigated. It was found that with an increase in the concentration of nanofibers, the average size of the matrix particles decreased. The effects of the nanoparticle concentration (0.01–0.1 wt.%) on the elastic modulus and tensile strength were determined for materials at 25 °C, 400 °C, and 750 °C. It was shown that with an increase in the concentration of nanofibers, a 10–40% increase in the elastic modulus and ultimate tensile strength occurred. A comparison of the mechanical properties of nickel in a wide range of temperatures, obtained in this work with materials made by various technologies, is carried out. A description of nanofibers’ mechanisms of influence on the structure and mechanical properties of nickel is given. The possible impact of impurity phases on the properties of nickel is estimated. The tendency of changes in the mechanical properties of nickel, depending on the concentration of nanofibers, is shown.

Progress in the Development of a Mechanical Properties Microprobe

MRS Bulletin ◽  
1986 ◽  
Vol 11 (5) ◽  
pp. 15-21 ◽  
Author(s):  
W. C. Oliver
Keyword(s):  
Mechanical Properties ◽  
Mechanical Response ◽  
Quantitative Information ◽  
General Term ◽  
Strength Properties ◽  
Physical Measurements ◽  
Wide Range ◽  
The Matrix ◽  
Recent Developments ◽  
Skilled Practitioner

A mechanical properties microprobe is an exciting concept. A system with the ability to evaluate the mechanical response of a sample with submicron spacial resolution would have an extremely wide range of applications. Recent developments in hardware and understanding have placed this goal within our grasp.In 1971, J.J.Gilman wrote the following in his article, “Hardness—A Strength Microprobe”:“Hardness measurements are at once among the most maligned and the most magnificent of physical measurements. Maligned because they are often misinterpreted by the uninitiated, and magnificent because they are so efficient in generating information for the skilled practitioner. They can quickly yield quantitative information about the elastic, anelastic, plastic, viscous, and fracture properties of a great variety of both isotropic and anisotropic solids. The tools that are used are simple and the sample sizes that are needed are typically small, sometimes submicroscopic. This makes it unnecessary to have large specimens in order to measure strength properties and makes it possible to measure the properties of various microscopic particles within the matrix phase of a polyphase metal, mineral, or ceramic material. This is why hardness may be considered to be a strength microprobe.”These statements are worth repeating for two reasons. First, they point out the largely untapped potential for microin-dentation tests to improve our understanding of the mechanical properties of materials. Second, it is the first mention of hardness tests in the context of a strength microprobe. In this article the more general term of microindentation tests will be used, since hardness is only one of many properties that can be measured with such tests. In addition, the term mechanical properties microprobe (MPM) will be used rather than strength microprobe-again, to note the wide variety of properties that can be measured.

Effects of Consolidation Process on the Microstructure and Mechanical Properties of ODS Ferritic Alloy

2013 ◽  
Vol 747-748 ◽  
pp. 507-512 ◽  
Author(s):  
Tong Liu ◽  
Hai Long Shen ◽  
Tong Wen Zhang ◽  
Mu Zhu ◽  
Cheng Gong Qin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Hot Isostatic Pressing ◽  
Oxide Dispersion Strengthened ◽  
Consolidation Process ◽  
Ferritic Alloy ◽  
Plasma Sintering ◽  
The Matrix ◽  
Spark Plasma ◽  
Oxide Particles

The oxide-dispersion-strengthened (ODS) ferritic alloy powders (Fe-14Cr-3Al-2W-0.1Ti-0.35Y2O3) were prepared by mechanical alloying (MA) at a rotation speed of 720 rpm for 24 h. All the elements were mixed homogenously in the powder, and Cr and Al dissolved in α-Fe after MA. The bulk samples were produced by spark plasma sintering (SPS) at 950 and 50 MPa and by hot isostatic pressing (HIP) at 1150 and 130 MPa, respectively. The SPS sample showed a tensile strength of 730 MPa and a poor ductility due to the existence of pores in microsize. The HIP sample had a high tensile strength of 980 MPa, yield strength of 710 MPa and elongation of 10.3 %. The excellent mechanical properties of the HIP sample was due to the small grain size of the matrix of about 400 nm and the fine oxide particles of 5-40 nm.

scholarly journals The Extrusion and SPS of Zirconium–Copper Powders and Studies of Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3560
Author(s):  
Tomasz Skrzekut ◽  
Grzegorz Boczkal ◽  
Adam Zwoliński ◽  
Piotr Noga ◽  
Lucyna Jaworska ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Intermetallic Compounds ◽  
Room Temperature ◽  
Intermetallic Phase ◽  
Extrusion Process ◽  
Strength Properties ◽  
Plasma Sintering ◽  
Copper Powders ◽  
Spark Plasma ◽  
Zirconium Copper

Zr-2.5Cu and Zr-10Cu powder mixtures were consolidated in the extrusion process and using the spark plasma sintering technique. In these studies, material tests were carried out in the fields of phase composition, microstructure, hardness and tensile strength for Zr-Cu materials at room temperature (RT) and 400 °C. Fractography analysis of materials at room temperature and 400 °C was carried out. The research took into account the anisotropy of the materials obtained in the extrusion process. For the nonequilibrium SPS process, ZrCu2 and Cu10Zr7 intermetallic compounds formed in the material at sintering temperature. Extruded materials were composed mainly of α-Zr and ZrCu2. The presence of intermetallic compounds affected the reduction in the strength properties of the tested materials. The highest strength value of 205 MPa was obtained for the extruded Zr-2.5Cu, for which the samples were cut in the direction of extrusion. For materials with 10 wt.% copper, more participation of the intermetallic phase was formed, which lowered the mechanical properties of the obtained materials. In addition to brittle intermetallic phases, the materials were characterized by residual porosity, which also reduced the strength properties.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

The Investigation on Aluminium Alloys Automobile Wheel with Low-Titanium Content Produced by Electrolysis

2005 ◽  
Vol 475-479 ◽  
pp. 317-320 ◽  
Author(s):  
Jing Pei Xie ◽  
Ji Wen Li ◽  
Zhong Xia Liu ◽  
Ai Qin Wang ◽  
Yong Gang Weng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloys ◽  
Solution Treatment ◽  
A356 Alloy ◽  
Aging Treatment ◽  
Titanium Content ◽  
The Matrix ◽  
Automobile Wheel

The in-situ Ti alloying of aluminium alloys was fulfilled by electrolysis, and the material was made into A356 alloy and used in automobile wheels. The results show that the grains of the A356 alloy was refined and the second dendrites arm was shortened due to the in-situ Ti alloying. Trough 3-hour solution treatment and 2-hour aging treatment for the A356 alloy, the microstructures were homogeneous, and Si particles were spheroid and distribute in the matrix fully. The outstanding mechanical properties with tensile strength (σb≥300Mpa) and elongation values (δ≥10%) have been obtained because the heat treatment was optimized. Compared with the traditional materials, tensile strength and elongation were increased by 7.6~14.1% and 7.4~44.3% respectively. The qualities of the automobile wheels were improved remarkably.

Fabrication and Mechanical Properties of Dense/Porous β-Tricalcium Phosphate Bioceramics

2007 ◽  
Vol 330-332 ◽  
pp. 907-910
Author(s):  
Fa Ming Zhang ◽  
Jiang Chang ◽  
Jian Xi Lu ◽  
Kai Li Lin
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Exponential Growth ◽  
Weight Bearing ◽  
Area Ratio ◽  
Sectional Area ◽  
Cross Sectional ◽  
The Matrix ◽  
Porous Bioceramics

Attempt to increase the mechanical properties of porous bioceramics, a dense/porous structured β-TCP bioceramics that mimic the characteristics of nature bone were fabricated. Experimental results show that the dense/porous structured β-TCP bioceramics demonstrated excellent mechanical properties with compressive strength up to 74 MPa and elastic modulus up to 960 MPa, which could be tailored by the dense/porous cross-sectional area ratio obeying the rule of exponential growth. The interface between the dense and porous bioceramics is connected compactly and tightly with some micropores distributed in the matrix of both porous and dense counterparts. The dense/porous structure of β-TCP bioceramics may provide an effective way to increase the mechanical properties of porous bioceramics for bone regeneration at weight bearing sites.

scholarly journals Preparation and Mechanical Properties of Graphene Oxide: Cement Nanocomposites

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Fakhim Babak ◽  
Hassani Abolfazl ◽  
Rashidi Alimorad ◽  
Ghodousi Parviz
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Graphene Oxide ◽  
Cement Mortar ◽  
Cement Matrix ◽  
Cement Composites ◽  
Xrd Diffraction ◽  
Calcium Silicate Hydrates ◽  
The Matrix ◽  
Scanning Electron

We investigate the performance of graphene oxide (GO) in improving mechanical properties of cement composites. A polycarboxylate superplasticizer was used to improve the dispersion of GO flakes in the cement. The mechanical strength of graphene-cement nanocomposites containing 0.1–2 wt% GO and 0.5 wt% superplasticizer was measured and compared with that of cement prepared without GO. We found that the tensile strength of the cement mortar increased with GO content, reaching 1.5%, a 48% increase in tensile strength. Ultra high-resolution field emission scanning electron microscopy (FE-SEM) used to observe the fracture surface of samples containing 1.5 wt% GO indicated that the nano-GO flakes were well dispersed in the matrix, and no aggregates were observed. FE-SEM observation also revealed good bonding between the GO surfaces and the surrounding cement matrix. In addition, XRD diffraction data showed growth of the calcium silicate hydrates (C-S-H) gels in GO cement mortar compared with the normal cement mortar.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Sign in / Sign up

Export Citation Format

Share Document