scholarly journals Synthesis and Characterization of Copper Impregnated Mesoporous Carbon as Heterogeneous Catalyst for Phenylacetylene Carboxylation with Carbon Dioxide

2020 ◽  
Vol 21 (1) ◽  
pp. 77
Author(s):  
Putri Nurul Amalia ◽  
Iman Abdullah ◽  
Dyah Utami Cahyaning Rahayu ◽  
Yuni Krisyuningsih Krisnandi
Keyword(s):  
Carbon Dioxide ◽  
Surface Area ◽  
Mesoporous Carbon ◽  
High Surface ◽  
High Surface Area ◽  
Bet Surface Area ◽  
Soft Template ◽  
Average Pore ◽  
Carbon Dioxide Co2

Carbon dioxide (CO2) is a compound that can potentially be used as a carbon source in the synthesis of fine chemicals. However, the utilization of CO2 is still constrained due to its inert and stable nature. Therefore, the presence of a catalyst is needed in CO2 conversion. This study aims to synthesize copper impregnated mesoporous carbon (Cu/MC) as a catalyst for phenylacetylene carboxylation reaction with CO2 to produce phenylpropiolic acid. The synthesis of mesoporous carbon was performed via the soft template method. The as-synthesized Cu/MC material was characterized by FTIR, SAA, XRD, and SEM-EDX. BET surface area analysis of mesoporous carbon showed that the material has a high surface area of 405.8 m2/g with an average pore diameter of 7.2 nm. XRD pattern of Cu/MC indicates that Cu has been successfully impregnated in the form of Cu(0) and Cu(I). Phenylacetylene carboxylation reaction with CO2 was carried out by varying reaction temperatures (25, 50, and 75 °C), amount of catalyst (28.6, 57.2, and 85.8 mg), type of base (Cs2CO3, K2CO3, and Na2CO3), and variation of support. The reaction mixtures were analyzed by HPLC and showed that the highest phenylacetylene conversion of 41% was obtained for the reaction at 75 °C using Cs2CO3 as a base.

scholarly journals Synthesis and Gas-Permeation Characterization of a Novel High-Surface Area Polyamide Derived from 1,3,6,8-Tetramethyl-2,7-diaminotriptycene: Towards Polyamides of Intrinsic Microporosity (PIM-PAs)

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 361 ◽  
Author(s):  
Giuseppe Genduso ◽  
Bader Ghanem ◽  
Yingge Wang ◽  
Ingo Pinnau
Keyword(s):  
Surface Area ◽  
Gas Permeability ◽  
High Surface ◽  
High Surface Area ◽  
Gas Permeation ◽  
Bet Surface Area ◽  
Mixed Gas ◽  
Fractional Free Volume ◽  
Intrinsic Microporosity

A triptycene-based diamine, 1,3,6,8-tetramethyl-2,7-diamino-triptycene (TMDAT), was used for the synthesis of a novel solution-processable polyamide obtained via polycondensation reaction with 4,4′-(hexafluoroisopropylidene)bis(benzoic acid) (6FBBA). Molecular simulations confirmed that the tetrasubstitution with ortho-methyl groups in the triptycene building block reduced rotations around the C–N bond of the amide group leading to enhanced fractional free volume. Based on N2 sorption at 77 K, 6FBBA-TMDAT revealed microporosity with a Brunauer–Emmett–Teller (BET) surface area of 396 m2 g−1; to date, this is the highest value reported for a linear polyamide. The aged 6FBBA-TMDAT sample showed moderate pure-gas permeabilities (e.g., 198 barrer for H2, ~109 for CO2, and ~25 for O2) and permselectivities (e.g., αH2/CH4 of ~50) that position this polyamide close to the 2008 H2/CH4 and H2/N2 upper bounds. CO2–CH4 mixed-gas permeability experiments at 35 °C demonstrated poor plasticization resistance; mixed-gas permselectivity negatively deviated from the pure-gas values likely, due to the enhancement of CH4 diffusion induced by mixing effects.

Use of High Surface Area TiO2 Nanosheet in Dye-sensitized Solar Cell

2006 ◽  
Vol 951 ◽  
Author(s):  
Sorapong Pavasupree ◽  
Supachai Ngamsinlapasathian ◽  
Yoshikazu Suzuki ◽  
Susumu Yoshikawa
Keyword(s):  
Surface Area ◽  
Pore Diameter ◽  
High Surface ◽  
High Surface Area ◽  
Mesoporous Structure ◽  
Energy Conversion Efficiency ◽  
Bet Surface Area ◽  
Average Pore ◽  
Dye Sensitized ◽  
Solar Energy Conversion Efficiency

ABSTRACTHigh surface area nanosheet TiO2 with mesoporous structure were synthesized by hydrothermal method at 130 °C for 12 h. The samples characterized by XRD, SEM, TEM, SAED, and BET surface area. The nanosheet structure was slightly curved and approximately 50-100 nm in width and several nanometers in thickness. The as-synthesized nanosheet TiO2 had average pore diameter about 3-4 nm. The BET surface area and pore volume of the sample were about 642 m2/g and 0.774 cm3/g, respectively. The solar energy conversion efficiency (η) of the cell using nanorods/nanoparticles TiO2 (from the nanosheet calcined at 450 °C for 2 h) with mesoporous structure was about 7.08 % with Jsc of 16.35 mA/cm2, Voc of 0.703 V and ff of 0.627; while η of the cell using P-25 reached 5.82 % with Jsc of 12.74 mA/cm2, Voc of 0.704V and ff of 0.649.

scholarly journals New Porous Silicon-Containing Organic Polymers: Synthesis and Carbon Dioxide Uptake

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1488
Author(s):  
Safaa H. Mohamed ◽  
Ayad S. Hameed ◽  
Emad Yousif ◽  
Mohammad Hayal Alotaibi ◽  
Dina S. Ahmed ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Surface Area ◽  
Pore Volume ◽  
High Surface ◽  
High Surface Area ◽  
Organic Polymers ◽  
Average Pore ◽  
Carbon Dioxide Uptake ◽  
Design And Synthesis ◽  
The One

The design and synthesis of new multifunctional organic porous polymers has attracted significant attention over the years due to their favorable properties, which make them suitable for carbon dioxide storage. In this study, 2-, 3-, and 4-hydroxybenzaldehyde reacted with phenyltrichlorosilane in the presence of a base, affording the corresponding organosilicons 1–3, which further reacted with benzidine in the presence of glacial acetic acid, yielding the organic polymers 4–6. The synthesized polymers exhibited microporous structures with a surface area of 8.174–18.012 m2 g−1, while their pore volume and total average pore diameter ranged from 0.015–0.035 cm3 g−1 and 1.947–1.952 nm, respectively. In addition, among the synthesized organic polymers, the one with the meta-arrangement structure 5 showed the highest carbon dioxide adsorption capacity at 323 K and 40 bar due to its relatively high surface area and pore volume.

scholarly journals Developing Eco-Friendly and Cost-Effective Porous Adsorbent for Carbon Dioxide Capture

Molecules ◽  
2021 ◽  
Vol 26 (7) ◽  
pp. 1962
Author(s):  
Mahboubeh Nabavinia ◽  
Baishali Kanjilal ◽  
Noahiro Fujinuma ◽  
Amos Mugweru ◽  
Iman Noshadi
Keyword(s):  
Carbon Dioxide ◽  
Surface Area ◽  
Co2 Capture ◽  
High Surface ◽  
Scale Up ◽  
Polymer Networks ◽  
High Surface Area ◽  
Excellent Thermal Stability ◽  
Doped Polymers ◽  
Metal Doped

To address the issue of global warming and climate change issues, recent research efforts have highlighted opportunities for capturing and electrochemically converting carbon dioxide (CO2). Despite metal doped polymers receiving widespread attention in this respect, the structures hitherto reported lack in ease of synthesis with scale up feasibility. In this study, a series of mesoporous metal-doped polymers (MRFs) with tunable metal functionality and hierarchical porosity were successfully synthesized using a one-step copolymerization of resorcinol and formaldehyde with Polyethyleneimine (PEI) under solvothermal conditions. The effect of PEI and metal doping concentrations were observed on physical properties and adsorption results. The results confirmed the role of PEI on the mesoporosity of the polymer networks and high surface area in addition to enhanced CO2 capture capacity. The resulting Cobalt doped material shows excellent thermal stability and promising CO2 capture performance, with equilibrium adsorption of 2.3 mmol CO2/g at 0 °C and 1 bar for at a surface area 675.62 m2/g. This mesoporous polymer, with its ease of synthesis is a promising candidate for promising for CO2 capture and possible subsequent electrochemical conversion.

Carbon Dioxide Sequestration Using Activated Carbon From Agro Waste-Waste Bamboo

2021 ◽  
Author(s):  
Emmanuel Ayodele ◽  
Victoria Ezeagwula ◽  
Precious Igbokwubiri
Keyword(s):  
Activated Carbon ◽  
Fly Ash ◽  
Greenhouse Gases ◽  
Surface Area ◽  
Carbon Capture ◽  
Agricultural Waste ◽  
High Surface ◽  
Research Work ◽  
High Surface Area ◽  
Bet Surface Area

Abstract Bamboo trees are one of the fastest growing trees in tropical rainforests around the world, they have various uses ranging from construction to fly ash generation used in oil and gas cementing, to development of activated carbon which is one of the latest uses of bamboo trees. This paper focuses on development of activated carbon from bamboo trees for carbon capture and sequestration. The need for improved air quality becomes imperative as the SDG Goal 12 and SDG Goal13 implies. One of the major greenhouse gases is CO2 which accounts for over 80% of greenhouse gases in the environment. Eliminating the greenhouse gases without adding another pollutant to the environment is highly sought after in the 21st century. Bamboo trees are mostly seen as agricultural waste with the advent of scaffolding and other support systems being in the construction industry. Instead of burning bamboo trees or using them for cooking in the local communities which in turn generates CO2 and fly ash, an alternative was considered in this research work, which is the usage of bamboo trees to generate activated, moderately porous and high surface area carbon for extracting CO2 from various CO2 discharge sources atmosphere and for water purification. This paper focuses on the quality testing of activated carbon that can effectively absorb CO2. The porosity, pore volume, bulk volume, and BET surface area were measured. The porosity of the activated carbon is 27%, BET surface area as 1260m²/g. Fixed carbon was 11.7%, Volatility 73%, ash content 1.7%.

Sign in / Sign up

Export Citation Format

Share Document