scholarly journals Experimental Study on Influence of Methylcellulose on Tensile and Flexural Strength of Normal Strength Ordinary Portland Cement Concrete

2021 ◽  
Vol 40 (4) ◽  
pp. 703-713
Author(s):  
Ali Ahmed ◽  
Shakir Ahmad ◽  
Muhammad Mannal Kaleem ◽  
Muhammad Bilal Zahid
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Control Sample ◽  
Modulus Of Rupture ◽  
Compression Tests ◽  
Portland Cement Concrete ◽  
Concrete Cylinder ◽  
Compressive Strength Of Concrete ◽  
Normal Strength

Current study explores the possibility of improvement in various categories of concrete’s strengths (including tensile strength, flexural strength etc.) by using methylcellulose as an additive. The effect of methylcellulose on concrete’s compressive strength has also been investigated experimentally. Concrete samples were casted with several methylcellulose to binder ratios varying from 0.002 to 0.01 by weight of cement. Several tests were performed on concrete specimens including concrete cylinder and cube compression tests, split cylinder tests and modulus of rupture tests. Results showed that addition of methylcellulose increased the tensile strength of concrete. Addition of 0.2% of methylcellulose increased the tensile strength of concrete by 16%. This increase in tensile strength reached up to 73% of the control sample on addition of 1% methylcellulose. It was observed that the effect of methylcellulose on compressive strength of concrete depends upon the type of samples being tested (cube or cylinder). The compressive strength of concrete cylinders showed a plateau behavior with peak at 0.4% methylcellulose content with an increase of 18.7%. Effect of methylcellulose on concrete cylinder strength becomes insignificant beyond 0.6%. It was observed that addition of methylcellulose reduces the modulus of rupture values. The reduction in MOR was only 3% at 0.2% methylcellulose content but it grew to 30% at 1% methylcellulose content. The research presents an effective way of increasing tensile strength of concrete but without significant effect on concrete’s compressive strength and modulus of rupture values. These findings can be used to determine optimum content of methylcellulose to achieve desired performance from concrete depending upon the intended use.

Advanced concretes for high temperature applications

2019 ◽  
Author(s):  
Alok A. Deshpande ◽  
Dhanendra Kumar ◽  
Ravi Ranade ◽  
Andrew S. Whittaker
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Strain Hardening ◽  
Modulus Of Rupture ◽  
Direct Tension ◽  
Conventional Concrete ◽  
Normal Strength ◽  
Temperature Applications

<p>The mechanical properties of concrete deteriorate at high temperatures. Strain-hardening cementitious composites (SHCC) are a special class of fiber-reinforced concretes that exhibit strain-hardening behavior in direct tension. The mechanical behavior of a SHCC made using polyvinyl alcohol (PVA) fibers is characterized after exposure to temperatures up to 800°C. The effects of temperature on compressive strength, splitting tensile strength and modulus of rupture are reported. For comparison, a normal strength conventional concrete of similar compressive strength to the SHCC was heated and tested in the same conditions as the SHCC. The normalized tensile strength of SHCC at room temperature, and after exposure to high temperature, is significantly greater than the value for conventional concrete. The PVA fibers provide crack-bridging capacity up to about 200°C (melting point of PVA fibers is 230°C), leading to improved tensile behavior. At greater temperatures, the fibers melt, creating pathways for steam to escape, reducing micro-cracking and significantly improving mechanical behavior with respect to conventional concrete. SHCC is a robust alternative to conventional concrete for high temperature applications.</p>

Relationship between Compressive, Splitting Tensile and Flexural Strength of Concrete Containing Granulated Waste Polyethylene Terephthalate (PET) Bottles as Fine Aggregate

2013 ◽  
Vol 795 ◽  
pp. 356-359 ◽  
Author(s):  
Mohd Irwan Juki ◽  
Mazni Awang ◽  
Mahamad Mohd Khairil Annas ◽  
Koh Heng Boon ◽  
Norzila Othman ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Fine Aggregate ◽  
Pet Bottles ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Waste Polyethylene

This paper describes the experimental investigation of relationship between splitting tensile strength and flexural strength with the compressive strength of concrete containing waste PET as fine aggregates replacement. Waste PET was reprocesses and used as the artificial fine aggregate at the replacement volume of 25%, 50% and 75%, Cylindrical and prism specimens were tested to obtain the compressive, splitting tensile and flexural strength at the age of 28 days. Based on the investigation, a relationship for the prediction of splitting tensile and flexural strength was derived from the compressive strength of concrete containing waste PET as fine agglegate replacement.

scholarly journals Properties of Concrete with Tire Derived Aggregate Partially Replacing Coarse Aggregates

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Gideon Siringi ◽  
Ali Abolmaali ◽  
Pranesh B. Aswath
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Modulus Of Rupture ◽  
Conventional Concrete ◽  
Mineral Aggregate ◽  
Coarse Aggregates ◽  
Strength Based ◽  
Tire Derived Aggregate

Tire derived aggregate (TDA) has been proposed as a possible lightweight replacement for mineral aggregate in concrete. The role played by the amount of TDA replacing coarse aggregate as well as different treatment and additives in concrete on its properties is examined. Conventional concrete (without TDA) and concrete containing TDA are compared by examining their compressive strength based on ASTM C39, workability based on ASTM C143, splitting tensile strength based on ASTM C496, modulus of rupture (flexural strength) based on ASTM C78, and bond stress based on ASTM C234. Results indicate that while replacement of coarse aggregates with TDA results in reduction in strength, it may be mitigated with addition of silica fume to obtain the desired strength. The greatest benefit of using TDA is in the development of a higher ductile product while utilizing recycled TDA.

scholarly journals Effect of Temperature on the Rate of Gain of Strength of Concrete

2019 ◽  
Vol 8 (6) ◽  
pp. 3906-3911
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Effect Of Temperature ◽  
Strength Parameters ◽  
Split Tensile Strength ◽  
Different Temperatures ◽  
Zero Degree ◽  
Hardened State ◽  
Compressive Strength Of Concrete

This paper presents the effect of temperature on the rate of gain of strength of concrete. Different samples of concrete were cast at different temperatures and various properties of concrete in fresh and hardened state were determined. It was observed that the three strength parameters viz. the compressive strength, the split tensile strength and the flexural strength of concrete are adversely affected when the temperature during first 24 hours is less than or equal to zero degree Celsius. The compressive strength of concrete was determined using 100mm and 150 mm cubes and a comparison was made between the two. It was observed that the strength of 100 mm cubes was greater than that of 150 mm cubes. Later a relationship was developed between 7 days,14 days and 28 days strength.

scholarly journals Strengths of Geo Polymer Concrete by Adding Metakaoline

2019 ◽  
Vol 8 (2) ◽  
pp. 2682-2687
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Point Of View ◽  
Polymer Concrete ◽  
Split Tensile Strength ◽  
Compressive Strength Of Concrete

Based0on the results obtained from this study0,the following Conclusions seems to be valid. The increase0in percentage replacement of Fly Ash with Metakaoline from 0% to 10.00% causes increase in Slump value up to 5% and beyond that slump is decreased. This0shows workability is reducing as percentage of Metakaoline increased beyond 5%. Hence, 5% replacement of Fly ash with Metakaoline is suitable from workability0point of view. The increase in percentage replacement0of Fly ash with0Metakaoline from 0% to 5% causes increase in compressive strength of concrete from 17.6MPa to 22.6MPa. Further0increase in percentage replacement of Fly ash with Metakaoline from 5% to 10% causes decrease in the0compressive strength from 22.6MPa to 18.7MPa. Hence, 5.00% replacement of Fly Ash with Metakaoline is advisable from compressive strength point of view .The increase in percentage replacement of Fly ash with Metakaoline from 0% to 5% causes increase in0Split Tensile strength of concrete from 3.72MPa to 4.68MPa. Further0increase in0percentage replacement of Fly ash with Metakaoline from 5% to 10% causes decrease in the split Tensile strength from 4.68MPa to 3.94MPa. Hence, 5.00% replacement of Fly Ash with Metakaoline is advisable from Split Tensile strength point of view. The increase in percentage replacement of Fly ash with Metakaoline from 0% to 5% causes increase in0flexural strength of concrete from 3.0 MPa to 3.36 MPa. Further increase in percentage replacement of Fly ash with Metakaoline from 5% to 10% causes decrease in the flexural strength from 3.36MPa to 3.2MPa.Hence 5.00% replacement of fly ash with Metakaoline is advisable from flexural strength point of view.Finally,it can conclude keeping in view of the workability ,compressive strength ,split tensile strength and flexural strength in mind,5% replacement of fly ash with Metakaolin is recommended for use in GEO POLYMER CONCRETE (GPC).

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

Development of Nanocement Mortar as a Construction Material

2013 ◽  
Vol 795 ◽  
pp. 684-691 ◽  
Author(s):  
Wail N. Al-Rifaie ◽  
Omar Mohanad Mahdi ◽  
Waleed Khalil Ahmed
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Construction Material ◽  
Modulus Of Rupture ◽  
Early Stages

The present research examined the compressive and flexural strength of nanocement mortar by using micro cement, micro sand, nanosilica and nanoclay in developing a nanocement mortar which can lead to improvements in ferrocement construction. The measured results demonstrate the increase in compressive and flexural strength of mortars at early stages of hardening. In addition, the influence of heating on compressive strength of cement mortar. General expressions to predict the compressive strength, modulus of rupture for the developed nanocement mortar in the present work are proposed.

Test Comparison Research Mechanics Performance between Sisal Fiber Concrete and Rubber Powder Concrete

2011 ◽  
Vol 243-249 ◽  
pp. 494-498
Author(s):  
Hui Ming Bao
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Sisal Fiber ◽  
Environment Friendly ◽  
Rubber Powder ◽  
Comparison Research ◽  
Mechanics Performance ◽  
Fiber Concrete ◽  
Sisal Fibers

By means of the tests on the mechanics performance of the reinforcing concrete mixed with sisal fibers or rubber powder of certain content are investigated. The compressive strength, tensile strength and flexural strength, etc. are compared. The test indicates that when the test condition is same, the compressive strength, tensile strength and flexural strength of the sisal fibers concrete are better than those of the rubber powder’s. The sisal fiber concrete is environment friendly than the rubber powder concrete. And it has widely value of spread and utilization.

Effect of using magnetic water on the mechanical properties of concrete exposed to elevated temperature

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wasim Barham ◽  
Ammar AL-Maabreh ◽  
Omar Latayfeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Tap Water ◽  
Splitting Tensile Strength ◽  
Content Type ◽  
Normal Water ◽  
Magnetic Water

PurposeThe influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.Design/methodology/approachExperimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.FindingsExposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.Originality/valuePrevious research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

scholarly journals The Mechanical Properties of Steel-Polypropylene Fibre Composites Concrete (HyFRCC)

2015 ◽  
Vol 773-774 ◽  
pp. 949-953 ◽  
Author(s):  
Izni Syahrizal Ibrahim ◽  
Wan Amizah Wan Jusoh ◽  
Abdul Rahman Mohd Sam ◽  
Nur Ain Mustapa ◽  
Sk Muiz Sk Abdul Razak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Concrete Strength ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Polypropylene Fibre ◽  
Experimental Results

This paper discusses the experimental results on the mechanical properties of hybrid fibre reinforced composite concrete (HyFRCC) containing different proportions of steel fibre (SF) and polypropylene fibre (PPF). The mechanical properties include compressive strength, tensile strength, and flexural strength. SF is known to enhance the flexural and tensile strengths, and at the same time is able to resist the formation of macro cracking. Meanwhile, PPF contributes to the tensile strain capacity and compressive strength, and also delay the formation of micro cracks. Hooked-end deformed type SF fibre with 60 mm length and fibrillated virgin type PPF fibre with 19 mm length are used in this study. Meanwhile, the concrete strength is maintained for grade C30. The percentage proportion of SF-PPF fibres are varied in the range of 100-0%, 75-25%, 50-50%, 25-75% and 0-100% of which the total fibre volume fraction (Vf) is fixed at 0.5%. The experimental results reveal that the percentage proportion of SF-PPF fibres with 75-25% produced the maximum performance of flexural strength, tensile strength and flexural toughness. Meanwhile, the percentage proportion of SF-PPF fibres with 100-0% contributes to the improvement of the compressive strength compared to that of plain concrete.

Sign in / Sign up

Export Citation Format

Share Document