SIFAT FISIK DAN MEKANIK PAPAN PARTIKEL DARI LIMBAH PLASTIK JENIS HDPE (High Density Polyetylene) DAN RANTING/CABANG KARET (Hevea brasiliensis Muell.Arg)

2011 ◽  
Vol 3 (1) ◽  
pp. 7
Author(s):  
Sari Mirad Noor
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Plastic Waste ◽  
High Density ◽  
Different Types ◽  
Materials Used ◽  
The Impact

The need of log increace rapidly, mean while forest product decrease, so efficiency on wood process should be done wisely, in the other hand plastic waste is uncompossed material, become an environmental problems. This research aims to determine the impact of particles of type HDPE plastic wastes and twigs/branches of rubber on some physical and mechanical properties of wood. Physical properties have been tested for water content, density, thickness, and water absorption. Although mechanical properties tests were tough Broken/Module of Rufture (MOR) and the preservation of architecture/modulus of elasticity (MOE).     The raw materials used are polyethylene of high density of waste plastic and rubber adhesive urea formaldehyde branch branch. Experimental design used the randomized Completely Design (RCD) 5 x 4, in which each treatment became much like 5 times replicated).The treatment used is the diversity of the composition of the waste of plastic of different types of polyethylene of high density provides a significant effect on the content of water, water absorption, the density and the development of thickness. With regard to the persistence and the fracture of the arch determination not to give a significant effect.Keywords: physical and mechanical properties, particle board, HDPE plastic waste, branch/twig of  rubber.

Comparison of Mechanical Properties of Fly Ash Artificial Geopolymer Aggregates with Natural Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 290-295 ◽  
Author(s):  
Alida Abdullah ◽  
Ku Amirrul Rahman Ku Yin ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Mien Van Tran
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Specific Gravity ◽  
Water Absorption ◽  
Raw Materials ◽  
Construction Materials ◽  
High Water ◽  
Natural Aggregate ◽  
Materials Used ◽  
The Impact

This study was conducted to compare the mechanical properties of fly ash artificial geopolymer aggregates with natural aggregate (rock) in term of its impact strength, specific gravity and water absorption.The raw materials used were fly ash, sodium hydroxide, sodium silicate and natural aggregate. After the artificial geopolymer aggregate has been produced, its water absorption, specific gravity and aggregate impact test has been done. All results obtained were compared to natural aggregate. The result shows that the fly ash geopolymer aggregate are lighter than natural aggregate in term of its specific gravity. The impact value for fly ash artificial geopolymer aggregate slightly high compared to natural aggregate while it has high water absorption value compared to natural aggregate. As conclusion, the fly ash artificial geopolymer aggregate can be used as one of the construction materials in concrete as an alternative for coarse aggregate besides natural aggregate with more lightweight properties.

scholarly journals SIFAT FISIK DAN MEKANIK PAPAN PARTIKEL BERDASARKAN KOMPOSISI LIMBAH KULIT BUAH PINANG DAN LIMBAH KAYU GERGAJIAN DENGAN VARIASI KADAR PEREKAT

2021 ◽  
Vol 9 (2) ◽  
pp. 207
Author(s):  
Asmawati Wurya Sari ◽  
M Dirhamsyah ◽  
Yuliati Indrayani
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Betel Nut ◽  
Particle Board ◽  
Composition Ratio

This research aimed to analyze the physical and mechanical properties of particleboard based on the composition of raw materials and adhesive content as well as their interaction with the optimum quality of particle boards that meet JIS A 5908-2003 standards. The particleboard was made with a size of 30 cm x 30 cm x 1 cm with a target density of 0.7 g/cm³.  The pressing was done at a temperature of 140°C for 8 minutes with a pressure of 25 kg/cm². The composition ratio of betel nut peel waste and sawdust varied, namely 60% betel nut peel waste: 40% sawdust, 50% betel nut peel waste: 50% sawdust, and 40% betel nut peel waste: sawdust 60%. The adhesive used was Urea Formaldehyde with a concentration of 12%, 14%, and 16%. The results showed that all test values met the JIS A 5908: 2003 standard except the MOE test. The optimum value of particle board of betel nut peel and sawdust was with a composition ratio of 50% betel nut peel waste: 50% sawdust, 16% adhesive content, with a density value of 0.6876 g/cm³, a moisture content of 9,4530%, water absorption 34,5306%, thickness expansion 8,2508%, MOE 12432,6243 kg/cm², MOR 205,8462 kg/cm², adhesive firmness 2,2530 kg/cm², screw holding strength 81,6861 kg/cm².Keywords: adhesive content, betel nut peel waste, material composition, mechanical properties, particleboard, physical.Abstrak Penelitian ini bertujuan untuk menganalisis sifat fisik dan mekanik papan partikel berdasarkan komposisi bahan baku dan kadar perekat serta interaksi keduanya terhadap kualitas papan partikel yang optimum serta memenuhi standar JIS A 5908-2003. Papan partikel dibuat dengan ukuran 30 cm x 30 cm x 1 cm dengan target kerapatan 0,7 g/cm³. Pengepresan  pada suhu 140°C selama 8 menit dengan tekanan 25 kg/cm². Perbandingan komposisi kulit buah pinang dan serbuk kayu gergaji bervariasi yaitu kulit buah pinang 60% : serbuk kayu gergaji 40%, kulit buah pinang 50% : serbuk kayu gergaji 50% dan kulit buah pinang 40% : serbuk kayu gergaji 60%. Perekat yang digunakan adalah Urea Formaldehida dengan konsentrasi 12%, 14% dan 16%. Hasil penelitian menunjukkan semua nilai uji memenuhi standar JIS A 5908 : 2003 kecuali uji MOE. Nilai papan partikel kulit buah pinang dan serbuk kayu gergaji optimum dengan perbandingan komposisi kulit buah pinang 50% : serbuk kayu gergaji 50%, kadar perekat 16%, dengan nilai densitas 0,6876 g/cm³, kadar air 9,4530%, daya serap air 34,5306%, pengembangan tebal 8,2508%, MOE 12432,6243 kg/cm², MOR 205,8462 kg/cm², Keteguhan rekat 2,2530 kg/cm², kekuatan menahan sekrup 81,6861 kg/cm².Kata kunci : papan partikel, kadar perekat, kulit buah pinang, komposisi bahan, sifat fisik dan mekanik.

scholarly journals EFFECTS OF DENSITY OF SAGO/UREA FORMALDEHYDE PARTICLEBOARD TOWARDS ITS THERMAL STABILITY, MECHANICAL AND PHYSICAL PROPERTIES

2016 ◽  
Vol 78 (10) ◽  
Author(s):  
Tay Chen Chiang ◽  
Sinin Hamdan ◽  
Mohd Shahril Osman
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Physical Properties ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Great Influence ◽  
Physical And Mechanical Properties ◽  
Internal Bonding ◽  
Scanning Calorimetry

This study examined the effect of density on the thermal stability, physical and mechanical properties of sago particleboard. Sago particles and Urea Formaldehyde (UF) were used as raw materials in the fabrication process. The fabrication and testing method were based on JIS A 5908 standard. The samples were prepared based on different desired density and went through a series of thermal stability, mechanical and physical tests. Mechanical properties of the composites were characterized by tensile, flexural, impact strength, screw test and internal bonding which had great influence on the particleboard performance. All the panels were tested for physical properties (water absorption and thickness swelling) to identify their use for indoor application. Thermal properties like thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) for the Sago/UF composites were analysed. The results showed particleboard with 800 kg/m3 exhibited the optimum strength on Internal Bonding, Screw test, Bending and Flexure test. Particleboard with 700 kg/m3 has better performance on Impact test. 500 kg/m3 showed better curing properties with DSC. TGA showed that all the Sago/UF particleboard decompose with single-stage and were decomposed into three main steps like water absorption, volatile and char.

scholarly journals Eco-Friendly, High-Density Fiberboards Bonded with Urea-Formaldehyde and Ammonium Lignosulfonate

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 220
Author(s):  
Petar Antov ◽  
Viktor Savov ◽  
Ľuboš Krišťák ◽  
Roman Réh ◽  
George I. Mantanis
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
High Density ◽  
Thickness Swelling ◽  
Formaldehyde Content ◽  
Uf Resin ◽  
Natural Wood ◽  
European Standards

The potential of producing eco-friendly, formaldehyde-free, high-density fiberboard (HDF) panels from hardwood fibers bonded with urea-formaldehyde (UF) resin and a novel ammonium lignosulfonate (ALS) is investigated in this paper. HDF panels were fabricated in the laboratory by applying a very low UF gluing factor (3%) and ALS content varying from 6% to 10% (based on the dry fibers). The physical and mechanical properties of the fiberboards, such as water absorption (WA), thickness swelling (TS), modulus of elasticity (MOE), bending strength (MOR), internal bond strength (IB), as well as formaldehyde content, were determined in accordance with the corresponding European standards. Overall, the HDF panels exhibited very satisfactory physical and mechanical properties, fully complying with the standard requirements of HDF for use in load-bearing applications in humid conditions. Markedly, the formaldehyde content of the laboratory fabricated panels was extremely low, ranging between 0.7–1.0 mg/100 g, which is, in fact, equivalent to the formaldehyde release of natural wood.

scholarly journals KUALITAS PAPAN PARTIKEL BERDASARKAN KOMPOSISI SEKAM PADI DAN KAYU SENGON DENGAN VARIASI KADAR PEREKAT

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Dendi Prayoga ◽  
. Dirhamsyah ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Rice Husk ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Solid Content ◽  
Particle Board ◽  
Rice Husks ◽  
Wood Processing

This research aimed to examine the physical and mechanical properties of particle boards based on the composition of raw materials and adhesive content and know the treatment of the composition of raw materials and the best adhesive content and meet the standard JIS A 5908-2003. The research was conducted at Wood Workshop Laboratory, Wood Processing Laboratory Faculty of Forestry,Tanjungpura University and Laboratory of PT. Duta Pertiwi Nusantara Pontianak. The adhesive used is Urea Formaldehyde with 52% Solid Content. Comparison of the composition of rice husks and sengon varies namely rice husk 50%: sengon 50%, rice husk 60%: sengon 40% and rice husk 70%: sengon 30%  and variations in the levels of UF adhesives, namely 14% and 16%, with target density 0,7 gr/cm3. The particleboard was 30 cm x 30 cm x 1 cm Pressing at temperature 140oC for 8 minutes, with  pressure of 25 kg/cm2. The research results of the study of density and moisture content meet the standards JIS A 5908-2003. The best particle values of rice husk and sengon  with composition a ratio of  rice husk 50%: sengon 50% , 16% adhesive content  16%, with density value of  0,7072 gr/cm3, moisture content 9,1949 %, thick development 12,3210 %, water absorption 68,8270 %, MOE 12110,7273 kg/cm2, MOR 161,0025 kg/cm2, firmness sticky 1,9320 kg/cm2, screw holding strength 62,3124 kg.Keywords : adhesive, composition, particle board, rice husk, sengon

An attempt to use „Tetra Pak” waste material in particleboard technology

2021 ◽  
Vol 114 ◽  
pp. 70-75
Author(s):  
Radosław Auriga ◽  
Piotr Borysiuk ◽  
Alicja Auriga
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Core Layer ◽  
Waste Material ◽  
Thickness Swelling ◽  
The Core ◽  
Tetra Pak ◽  
The Impact

An attempt to use „Tetra Pak” waste material in particleboard technology. The study investigates the effect of addition Tetra Pak waste material in the core layer on physical and mechanical properties of chipboard. Three-layer chipboards with a thickness of 16 mm and a density of 650 kg / m3 were manufactured. The share of Tetra Pak waste material in the boards was varied: 0%, 5%, 10% and 25%. The density profile was measured to determine the impact of Tetra Pak share on the density distribution. In addition, the manufactured boards were tested for strength (MOR, MOE, IB), thickness swelling and water absorption after immersion in water for 2 and 24 hours. The tests revealed that Tetra Pak share does not affect significantly the value of static bending strength and modulus of elasticity of the chipboard, but it significantly decreases IB. Also, it has been found that Tetra Pak insignificantly decreases the value of swelling and water absorption of the chipboards.

scholarly journals Environmentally-Friendly High-Density Polyethylene-Bonded Plywood Panels

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1166 ◽  
Author(s):  
Pavlo Bekhta ◽  
Ján Sedliačik
Keyword(s):  
Mechanical Properties ◽  
Hot Pressing ◽  
High Density Polyethylene ◽  
Phenol Formaldehyde ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Core Layer ◽  
High Density ◽  
Pressing Pressure ◽  
Pressing Time

Thermoplastic films exhibit good potential to be used as adhesives for the production of veneer-based composites. This work presents the first effort to develop and evaluate composites based on alder veneers and high-density polyethylene (HDPE) film. The effects of hot-pressing temperature (140, 160, and 180 °C), hot-pressing pressure (0.8, 1.2, and 1.6 MPa), hot-pressing time (1, 2, 3, and 5 min), and type of adhesives on the physical and mechanical properties of alder plywood panels were investigated. The effects of these variables on the core-layer temperature during the hot pressing of multiplywood panels using various adhesives were also studied. Three types of adhesives were used: urea–formaldehyde (UF), phenol–formaldehyde (PF), and HDPE film. UF and PF adhesives were used for the comparison. The findings of this work indicate that formaldehyde-free HDPE film adhesive gave values of mechanical properties of alder plywood panels that are comparable to those obtained with traditional UF and PF adhesives, even though the adhesive dosage and pressing pressure were lower than when UF and PF adhesives were used. The obtained bonding strength values of HDPE-bonded alder plywood panels ranged from 0.74 to 2.38 MPa and met the European Standard EN 314-2 for Class 1 plywood. The optimum conditions for the bonding of HDPE plywood were 160 °C, 0.8 MPa, and 3 min.

Development of the New Generation Materials for the Soft Pipe Lining Rehabilitation

2005 ◽  
Author(s):  
Hsin Her Yu ◽  
Min-Hsun Cheng ◽  
Rong-Yuan Jou ◽  
Kuang-Chyi Lee ◽  
Chien-Chang Lin
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resins ◽  
Potable Water ◽  
Raw Materials ◽  
Trade Mark ◽  
Power Cables ◽  
Different Types ◽  
Materials Used ◽  
New Generation ◽  
Optimum Sample

With increasing global urbanization and industrialization, many more pipelines for gas, potable water, sewer, oil, and power cables have been installed underground, underwater, in buildings and in factories. Maintenance of such pipelines is crucial. However, it is often difficult and has become a growing problem these days. The PALTEM-HL (Trade mark and stands for Pipeline Automatic Lining SysTEM, Hose Lining Method), a pipeline relining system, was developed as an effective and inexpensive solution for this problem. In this project, we try to develop a new resins and the adhesives system to replace the raw materials used in the PALTEM-HL system. Anionic harder combined two different types of epoxy resins were investigated in this study. After curing, the mechanical properties and glass transition temperature of the mixture were examined and the optimum sample preparation prescription was also found. FTIR (Fourier Transform Infrared Spectroscopy) and DSC (Differential Scanning Calorimeter) were employed to monitor the curing process of the mixtures. The mechanical properties of the mixture were also measured by Instron and micro Vickers.

Dispersing the Charge as a Way to Improve the Quality of Ceramic Bricks

2018 ◽  
Vol 931 ◽  
pp. 558-563 ◽  
Author(s):  
Viktoriya A. Guryeva ◽  
Viktor V. Dubineckij ◽  
Aleksandr V. Doroshin
Keyword(s):  
Mechanical Properties ◽  
Original Composition ◽  
Water Absorption ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Dust Particles ◽  
Drill Cuttings ◽  
Additional Processing ◽  
Grinding Time

Investigations of the influence of dispersion of feedstock on the basis of clay of the Buguruslan deposit and drill cuttings from the facilities of PJSC «Orenburgneft» have been carried out, it is revealed that as the grinding time increases, the content of clay and dust particles increases. Intensive sintering of the samples between 1000 °C and 1100 °C has been established, which is confirmed by the compaction of the samples and the decrease in the water absorption of the ceramic masses. Minimal water absorption, within 2.35%, showed a sample of 3-hour grinding, and a sample of a 2-hour grinding of 8.34%. As a result of the study of dispersion of the charge on the basis of clay raw materials and drill cuttings, it was found that by subjecting the original composition to additional processing, within 2 hours, the physical and mechanical properties of ceramic bricks can be improved.

Effects of Caeser Weed (Urena lobata L ) Fibre, Afara (Terminalia superba) and Mahogany (Khaya senegalensis) Dusts on some Physical and Mechanical Properties of Epoxy Resin

2012 ◽  
Vol 7 ◽  
pp. 21-33
Author(s):  
Ishaya Musa Dagwa ◽  
O. Ojo
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Epoxy Resin ◽  
Tensile Modulus ◽  
Physical And Mechanical Properties ◽  
Shore Hardness ◽  
Fibre Filler ◽  
Standard Procedures ◽  
The Impact ◽  
Positive Effect

In Recent Times, Environmental Concerns Arising from Pollution, Global Warming and Waste Management Have Led to the Generation of Interest in the Use of Environmentally Friendly Materials, Especially, Biological Materials such as Natural Fibres and Particulates in Composite Materials Manufacture. in this Work, Natural Fillers (Afara-Mahogany Particulates of 150µm) and Fibre (Caesar Weed Fibre of 5mm Length) Were Mixed with Epoxy Resin at the Various Fibre/filler Weight Percentages as Follows: 2%, 4%, 6%, 8% and 10% with Random Fibre Orientations. some Physical and Mechanical Properties of the Composite Were Determined Using Standard Procedures. Ninety (90) Wt% of Epoxy Resin Mixed with 10 Wt% for each of the Following: Caeser Weed Fibre, Afara and Mahogany, Improved the Tensile Modulus by 2652.6%, 321.37%, and 129.73% and the Impact Strength by 162.7%, 133.9% and 15.25%, Respectively. Also, Composites Density Reduced by 26.26%, 3.03%, and 3.03%, and its Hardness too Reduced by 5.41%, 1.35%, and 4.05%, Respectively. Meanwhile, the Water Absorption Were 4.9%, 2.79%, and 4.12% for 10wt% of Caeser Weed Fibre, Afara and Mahogany, Respectively and 90wt% Epoxy Resin. Therefore, Caeser Weed Fibre Had the Greatest Positive Effect on the Tensile Strength, Impact Energy Absorbed and Density. however, Afara-Epoxy Composite Had the Least Water Absorption and Higher Shore Hardness Value than Mahogany-Epoxy and Caeser Weed Fibre-Epoxy Composites.

Sign in / Sign up

Export Citation Format

Share Document