Comparison of Mechanical Properties of Fly Ash Artificial Geopolymer Aggregates with Natural Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 290-295 ◽  
Author(s):  
Alida Abdullah ◽  
Ku Amirrul Rahman Ku Yin ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Mien Van Tran
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Specific Gravity ◽  
Water Absorption ◽  
Raw Materials ◽  
Construction Materials ◽  
High Water ◽  
Natural Aggregate ◽  
Materials Used ◽  
The Impact

This study was conducted to compare the mechanical properties of fly ash artificial geopolymer aggregates with natural aggregate (rock) in term of its impact strength, specific gravity and water absorption.The raw materials used were fly ash, sodium hydroxide, sodium silicate and natural aggregate. After the artificial geopolymer aggregate has been produced, its water absorption, specific gravity and aggregate impact test has been done. All results obtained were compared to natural aggregate. The result shows that the fly ash geopolymer aggregate are lighter than natural aggregate in term of its specific gravity. The impact value for fly ash artificial geopolymer aggregate slightly high compared to natural aggregate while it has high water absorption value compared to natural aggregate. As conclusion, the fly ash artificial geopolymer aggregate can be used as one of the construction materials in concrete as an alternative for coarse aggregate besides natural aggregate with more lightweight properties.

SIFAT FISIK DAN MEKANIK PAPAN PARTIKEL DARI LIMBAH PLASTIK JENIS HDPE (High Density Polyetylene) DAN RANTING/CABANG KARET (Hevea brasiliensis Muell.Arg)

2011 ◽  
Vol 3 (1) ◽  
pp. 7
Author(s):  
Sari Mirad Noor
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Plastic Waste ◽  
High Density ◽  
Different Types ◽  
Materials Used ◽  
The Impact

The need of log increace rapidly, mean while forest product decrease, so efficiency on wood process should be done wisely, in the other hand plastic waste is uncompossed material, become an environmental problems. This research aims to determine the impact of particles of type HDPE plastic wastes and twigs/branches of rubber on some physical and mechanical properties of wood. Physical properties have been tested for water content, density, thickness, and water absorption. Although mechanical properties tests were tough Broken/Module of Rufture (MOR) and the preservation of architecture/modulus of elasticity (MOE).     The raw materials used are polyethylene of high density of waste plastic and rubber adhesive urea formaldehyde branch branch. Experimental design used the randomized Completely Design (RCD) 5 x 4, in which each treatment became much like 5 times replicated).The treatment used is the diversity of the composition of the waste of plastic of different types of polyethylene of high density provides a significant effect on the content of water, water absorption, the density and the development of thickness. With regard to the persistence and the fracture of the arch determination not to give a significant effect.Keywords: physical and mechanical properties, particle board, HDPE plastic waste, branch/twig of  rubber.

Development of Fly Ash-Based Geopolymer Lightweight Bricks Using Foaming Agent - A Review

2015 ◽  
Vol 660 ◽  
pp. 9-16 ◽  
Author(s):  
Wan Mastura Wan Ibrahim ◽  
Kamarudin Hussin ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Aeslina Abdul Kadir ◽  
Mohammed Binhussain
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Building Material ◽  
Raw Materials ◽  
Construction Materials ◽  
Physical And Mechanical Properties ◽  
Foaming Agent ◽  
Positive Effects ◽  
The World ◽  
Great Development

Bricks are widely used as a construction and building material due to its properties. Recent years have seen a great development in new types of inorganic cementitious binders called ‘‘geopolymeric cement’’ around the world. This prompted its use in bricks, which improves the greenness of ordinary bricks. The development of fly ash-based geopolymer lightweight bricks is relatively new in the field of construction materials. This paper reviews the uses of fly ash as a raw materials and addition of foaming agent to the geopolymeric mixture to produce lightweight bricks. The effects on their physical and mechanical properties have been discussed. Most manufactured bricks with incorporation of foaming agent have shown positive effects by producing lightweight bricks, increased porosity and improved the thermal conductivities of fly ash-based geopolymer bricks. However, less of performances in number of cases in terms of mechanical properties were also demonstrated.

scholarly journals Use of Plastic Aggregates in Concrete

2019 ◽  
Vol 9 (1) ◽  
pp. 4406-4412
Keyword(s):  
Mechanical Properties ◽  
Carbon Dioxide ◽  
Fly Ash ◽  
Construction Industry ◽  
Negative Impact ◽  
Raw Materials ◽  
Waste Products ◽  
Waste Plastic ◽  
Coarse Aggregates ◽  
Materials Used

There is no doubt concrete is most useful thing in construction industry but it has a negative impact also, just like a coin has two faces. Raw materials used in manufacturing of concrete affects the environment in one or the another negative way. Like manufacturing of cement produce carbon dioxide whereas the production of aggregates adds dust to the environment. Production of coarse aggregates also impact the geology of the area from they were extracted. A step taken in this direction is the use of waste products along with or in replacement of cement. Many of these materials are already in use, like silica fume, fly ash etc. In this study, plastic coarse aggregates were used in place of natural coarse aggregates. Plastic aggregates were produced by little processing of waste plastic. Plastic is the biggest threat to the environment, and it is affecting the environment rapidly. Some recent studies show that it can be used construction industry due to some of its properties like inert behavior, resistance to degradation etc. Also use of waste plastic can help in reducing plastic waste Various experiments were performed to test the mechanical properties of the concrete with plastic coarse aggregates. Concrete was prepared using plastic coarse aggregates in varying proportions of 0, 2.5, 5, 7.5 and 10%

scholarly journals Construction Materials Used in the Historical Roman Era Bath in Myra

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Cem Oguz ◽  
Fikret Turker ◽  
Niyazi Ugur Kockal
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Construction Materials ◽  
Sieve Analysis ◽  
Specific Mass ◽  
Loading Test ◽  
Historical Building ◽  
Roman Time ◽  
Stereo Microscope ◽  
Materials Used

The physical, chemical, and mechanical properties of mortars and bricks used in the historical building that was erected at Myra within the boundaries of Antalya Province during the Roman time were investigated. The sample picked points were marked on the air photographs and plans of the buildings and samples were photographed. Then petrographic evaluation was made by stereo microscope on the polished surfaces of construction materials (mortar, brick) taken from such historical buildings in laboratory condition. Also, microstructural analyses (SEM/EDX, XRD), physical analyses (unit volume, water absorption by mass, water absorption by volume, specific mass, compacity, and porosity), chemical analyses (acid loss and sieve analysis, salt analyses, pH, protein, fat, pozzolanic activity, and conductivity analyses), and mechanical experiments (compressive strength, point loading test, and tensile strength at bending) were applied and the obtained results were evaluated. It was observed that good adherence was provided between the binder and the aggregate in mortars. It was also detected that bricks have preserved their originality against environmental, atmospheric, and physicochemical effects and their mechanical properties showed that they were produced by appropriate techniques.

scholarly journals Mix Design and Mechanical Properties of Fly Ash and GGBFS-Synthesized Alkali-Activated Concrete (AAC)

2019 ◽  
Vol 4 (2) ◽  
pp. 20 ◽  
Author(s):  
Ramamohana Reddy Bellum ◽  
Ruben Nerella ◽  
Sri Rama Chand Madduru ◽  
Chandra Sekhar Reddy Indukuri
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Raw Materials ◽  
Construction Materials ◽  
Xrd Analysis ◽  
Mix Design ◽  
Geopolymer Concrete ◽  
Curing Conditions ◽  
Factors Affecting ◽  
Alkali Activated

Cement is one of the construction materials widely used around the world in order to develop infrastructure and it is also one of the factors affecting economies. The production of cement consumes a lot of raw materials like limestone, which releases CO2 into the atmosphere and thus leads to global warming. Many investigations are underway in this area, essentially focusing on the eco-accommodating environment. In the research, an alternative material to cement binder is geopolymer binder, with the same efficiency. This paper presents scanning electron microscope (SEM) and X-ray diffraction (XRD) analysis of factory byproducts (i.e., fly ash and ground granulated blast furnace slag (GGBFS)). The mix design process for the manufacture of alkali-activated geopolymer binders synthesized by fly ash and GGBFS is presented. The mechanical properties (compression, split tensile and flexural strength, bond strength) of geopolymer concrete at different mix proportions and at dissimilar curing conditions were also investigated. Geopolymer concrete synthesized with 30% fly ash and 70% GGBFS has better properties at 14 M of NaOH and cured in an oven for 24 h at 70 °C.

Properties of Lightweight Bubbles Aggregate (LBA) for the Replacement of Coarse Aggregates in Concrete

2014 ◽  
Vol 803 ◽  
pp. 11-15
Author(s):  
Norlia Mohamad Ibrahim ◽  
Leong Qi Wen ◽  
Roshazita Che Amat ◽  
Taksiah Abdul Majid ◽  
Nur Liza Rahim ◽  
...  
Keyword(s):  
Specific Gravity ◽  
Portland Cement ◽  
Water Absorption ◽  
Bulk Density ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Construction Materials ◽  
Cement Composite ◽  
Partial Replacement ◽  
Concrete Production

The depletion of natural resources in the production of coarse aggregate are very crucial. Construction materials are solely depends on natural granite in the making of cement composite. Therefore , there is an urgency need to develop new alternatives material that can replace the usage of granite in concrete production. In this study, LBA have been produced to cater this problem. It is made from a mixture of bubbles from foam and ordinary portland cement. The ratio of the raw materials used is 1 part of bubbles and 2 part of ordinary Portland cement. Its manufacturing process does not involving any sintering process so it will part help to reduce energy comsuption at about 30%. The properties and characteristics of the LBA such as density, specific gravity, water absorption, strength were investigated. Results shown that the specific gravity of LBA was 1.00, water absorption was 19.44%, dry bulk density was between 730 – 800 kg/m3 and dry loose bulk density was ranged from 700 to 730 kg/m3 and the strength of aggregates is 14.00 MPa. It is found that the LBA can be used as a partial replacement of granite in the production of concrete. Keywords: LBA, concrete, density

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

scholarly journals Cellulose Nanofibrils/Xyloglucan Bio-Based Aerogels with Shape Recovery

Gels ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 5
Author(s):  
Samuel Mandin ◽  
Samuel Moreau ◽  
Malika Talantikite ◽  
Bruno Novalès ◽  
Jean-Eudes Maigret ◽  
...  
Keyword(s):  
Water Absorption ◽  
Shape Recovery ◽  
Cellulose Nanofibrils ◽  
High Water ◽  
Absorption Capacity ◽  
Absorption Properties ◽  
High Affinity ◽  
High Water Absorption ◽  
Freezing Procedure ◽  
The Impact

Bio-based aerogels containing cellulose nanofibrils (CNFs) are promising materials due to the inherent physical properties of CNF. The high affinity of cellulose to plant hemicelluloses (xyloglucan, xylan, pectin) is also an opportunity to develop biomaterials with new properties. Here, we prepared aerogels from gelled dispersions of CNFs and xyloglucan (XG) at different ratios by using a freeze-casting procedure in unidirectional (UD) and non-directional (ND) manners. As showed by rheology analysis, CNF and CNF/XG dispersions behave as true gels. We investigated the impact of the freezing procedure and the gel’s composition on the microstructure and the water absorption properties. The introduction of XG greatly affects the microstructure of the aerogel from lamellar to cellular morphology. Bio-based aerogels showed high water absorption capacity with shape recovery after compression. The relation between morphology and aerogel compositions is discussed.

scholarly journals Green Packaging from Consumer and Business Perspectives

2021 ◽  
Vol 13 (3) ◽  
pp. 1356
Author(s):  
Gonzalo Wandosell ◽  
María C. Parra-Meroño ◽  
Alfredo Alcayde ◽  
Raúl Baños
Keyword(s):  
Sustainable Development ◽  
Raw Materials ◽  
Research Activity ◽  
Word Clouds ◽  
Climate Action ◽  
Green Packaging ◽  
Materials Used ◽  
Societal Challenge ◽  
Corporate Social ◽  
The Impact

Sustainable development is a global objective that aims to address the societal challenge of climate action, the environment, resource efficiency, and raw materials. In this sense, an important strategy is the promotion of green packaging, that is, the use of sustainable materials and designs for the packaging of goods. In recent years, many research works have been published in the specialised area covering the different perspectives and dimensions of green packaging. However, to our knowledge, no previous investigations have analysed the research activity on green packaging from business and consumer perspectives. The present study intends to fill this gap by analysing all of the publications found in the Scopus database with the help of visual analytic tools, including word clouds and Gephi network visualization software. More specifically, our study analyses the impact of green packaging from business and consumer viewpoints, including some specific issues such as the design and materials used in green packaging, green packaging costs, marketing strategies and corporate social responsibility related to green packaging, and the impact of green packaging in waste management, the circular economy, logistics, and supply chain management. The results obtained reveal the growing interest of scholars and researchers in all of these dimensions, as is made patently clear by the increasing number of journal publications in recent years. The practical implications of this study are significant, given the growing awareness among companies and consumers about the importance of the promotion of sustainable development through green packaging alternatives. More specifically, the results of this research could be very useful for all of those agents who are interested in learning about the main lines of research being developed in the field of green packaging.

Alternative Concrete – Geopolymer Concrete

2021 ◽  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Construction Industry ◽  
Building Material ◽  
Construction Materials ◽  
Raw Material ◽  
Geopolymer Concrete ◽  
Sustainable Solutions ◽  
New Construction ◽  
Alkali Activated

Concrete is the most versatile, durable and reliable material and is the most used building material. It requires large amounts of Portland cement which has environmental problems associated with its production. Hence, an alternative concrete – geopolymer concrete is needed. The general aim of this book is to make significant contributions in understanding and deciphering the mechanisms of the realization of the alkali-activated fly ash-based geopolymer concrete and, at the same time, to present the main characteristics of the materials, components, as well as the influence that they have on the performance of the mechanical properties of the concrete. The book deals with in-depth research of the potential recovery of fly ash and using it as a raw material for the development of new construction materials, offering sustainable solutions to the construction industry.

Sign in / Sign up

Export Citation Format

Share Document