scholarly journals The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment

2008 ◽  
Vol 15 (3) ◽  
pp. 49-58 ◽  
Author(s):  
Leszek Matuszewski ◽  
Zbigniew Szydło
Keyword(s):  
Magnetic Fluid ◽  
Sea Water ◽  
Water Environment ◽  
Colloidal Suspensions ◽  
Magnetic Fluids ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Design Activities ◽  
Pressure Water ◽  
Working Out

The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment Presented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MF seals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless (screw or centrifugal) fluid seal used as the first stage seal and then the MF seal as the main seal. Further parts of the article contain discuss of the properties of magnetic fluids in the construction of MF seals. Sample of the few systems of magnetic fluid seals are presented, which have been researched lately in our laboratory including sea conditions. The magnetic fluids used in our seals are colloidal suspensions of magnetic nanoparticles. Undertaken earlier various systems selection for sea-water purposes forced us to focus on double sealing systems, in which the MF seal is used as the second seal following a conventional system especially adapted to co-operation with MF systems. This solution successfully limits direct contact of the sealed liquid with the magnetic fluid, and the entire sealing construction secures absolute tightness of the system. Using this solution we also can reduce costs by elements high accuracy avoidance. Research and design activities are carried out in the AGH Laboratory of Seals and Magnetic Fluid Applications together with Deep Water Department of Technical University of Gdansk over the use of magnetic fluid seals in sea water environment. These activities are oriented on working out MF seals able to work effectively in machines in which low-pressure water flow takes place. The objects of experimental investigations are seals having two different nominal diameters: 50 mm and 220 mm and two research rigs of different construction had to be built up. Works are scheduled to be continued.

DEVELOPMENT OF INTEGRATED MONITORING NETWORK FOR MEASURING SALINITY OF SEA WATER

2018 ◽  
pp. 18-26
Author(s):  
Sima Ajdar qizi Askerova
Keyword(s):  
Surface Waters ◽  
Sea Water ◽  
Water Environment ◽  
Monitoring Network ◽  
Monitoring Networks ◽  
The Caspian Sea ◽  
Integrated Monitoring ◽  
Ecological Control ◽  
Different Depths ◽  
Optimal Construction

Monitoring of sea water condition is one of major requirements for carrying out the reliable ecological control of water environment. Monitoring networks contain such elements as sea buoys, beacons, etc. and are designated for measuringvarious hydrophysical parameters, including salinity of sea water. Development of specialized network and a separate buoy system for measuring thesea water salinity at different depths makes it possible to determine major regularities of processes of pollution and self-recovery of the sea waters. The article describes the scientific and methodological basics for development of this specialized network and questions of its optimal construction. It is well-known that at a depth of 30-45 m of the Caspian Sea salinity decreases and then at a depth of 45-60 m salinity is fully recovered. The mentioned changes of salinity at the relatively upper layer of sea waters is of special interest for studying the effect of ocean-going processes on the climate forming in the Caspian area. In terms of informativeness of measurements of surface waters salinity, the most informative is a layer ata 30-60 m depth, where inversion and recovery of salinity take place. It is shown that in most informative subrange of measurements, i. e. at a depth of 30-60 m optimization of regime of measurements complex should be carried out in order to increase the effectiveness of held researches. It is shown that at a depth of 35-50 m choice of the optimum regime of measurements makes it possible to obtain the maximum amount of information.

MEASURES FOR ENVIRONMENT CONSERVATION IN ENCLOSED COASTAL SEAS

2017 ◽  
Author(s):  
Keizo Negi ◽  
Keizo Negi ◽  
Takuya Ishikawa ◽  
Takuya Ishikawa ◽  
Kenichiro Iba ◽  
...  
Keyword(s):  
Water Pollution ◽  
Water Quality ◽  
Water Mass ◽  
Sea Water ◽  
Red Tide ◽  
Water Environment ◽  
Quality Standard ◽  
Tokyo Bay ◽  
View Point ◽  
High Concentration

Japan experienced serious water pollution during the period of high economic growth in 1960s. It was also the period that we had such damages to human health, fishery and living conditions due to red tide as much of chemicals, organic materials and the like flowing into the seas along the growing population and industries in the coastal areas. Notable in those days was the issues of environment conservation in the enclosed coastal seas where pollutants were prone to accumulate inside due to low level of water circulation, resulting in the issues including red tide and oxygen-deficient water mass. In responding to these issues, we implemented countermeasures like effluent control with the Water Pollution Control Law and improvement/expansion of sewage facilities. In the extensive enclosed coastal seas of Tokyo Bay, Ise Bay and the Seto Inland Sea, the three areas of high concentration of population, we implemented water quality total reduction in seven terms from 1979, reducing the total quantities of pollutant load of COD, TN and TP. Sea water quality hence has been on an improvement trend as a whole along the steady reduction of pollutants from the land. We however recognize that there are differences in improvement by sea area such as red tide and oxygen-deficient water mass continue to occur in some areas. Meanwhile, it has been pointed out that bio-diversity and bio-productivity should be secured through conservation/creation of tidal flats and seaweed beds in the view point of “Bountiful Sea” To work at these challenges, through the studies depending on the circumstances of the water environment in the enclosed coastal seas, we composed “The Policy of Desirable State of 8th TPLCS” in 2015. We have also added the sediment DO into the water quality standard related to the life-environmental items in view of the preservation of aquatic creatures in the enclosed water areas. Important from now on, along the Policy, is to proceed with necessary measures to improve water quality with good considerations of differences by area in the view point of “Beautiful and bountiful Sea”.

Effect of operating conditions on rejection of anionic pollutants in the water environment by nanofiltration especially in very low pressure range

1996 ◽  
Vol 34 (9) ◽  
pp. 149-156 ◽  
Author(s):  
C. Ratanatamskul ◽  
K. Yamamoto ◽  
T. Urase ◽  
S. Ohgaki
Keyword(s):  
Water Environment ◽  
Chloride Ions ◽  
Operating Conditions ◽  
Transmembrane Pressure ◽  
Operating Pressure ◽  
Nanofiltration Membranes ◽  
Single Solution ◽  
Crossflow Velocity ◽  
Membrane Type ◽  
New Generation

The recent development of new generation LPRO or nanofiltration membranes have received attraction for application in the field of wastewater and water treatment through an increasingly stringent regulation for drinking purpose and water reclamation. In this research, the application on treatment of anionic pollutants (nitrate, nitrite, phosphate, sulfate and chloride ions) have been investigated as functions of transmembrane pressure, crossflow velocity and temperature under very much lower pressure operation range (0.49 to 0.03 MPa) than any other previous research used to do. Negative rejection was also observed under very much low range of operating pressure in the case of membrane type NTR-7250. Moreover, the extended Nernst-Planck model was used for analysis of the experimental data of the rejection of nitrate, nitrite and chloride ions in single solution by considering effective charged density of the membranes.

Experimental investigations to predict optimistic biodiesel(s) and its optimistic operating conditions by varying ignition delay period and fuel spray pressures for lower emissions and better performance

2020 ◽  
Vol 234 (19) ◽  
pp. 3890-3902
Author(s):  
Vishal V Patil ◽  
Ranjit S Patil
Keyword(s):  
Methyl Ester ◽  
Ignition Delay ◽  
Seed Oil ◽  
Delay Period ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Rubber Seed Oil ◽  
Rubber Seed ◽  
Neem Seed Oil ◽  
Ignition Delay Period

In this study, different characteristics of sustainable renewable biodiesels (those have a high potential of their production worldwide and in India) were compared with the characteristics of neat diesel to determine optimistic biodiesel for the diesel engine at 250 bar spray pressure. Optimistic fuel gives a comparatively lower level of emissions and better performance than other selected fuels in the study. Rubber seed oil methyl ester was investigated as an optimistic fuel among the other selected fuels such as sunflower oil methyl ester, neem seed oil methyl ester, and neat diesel. To enhance the performance characteristics and to further decrease the level of emission characteristics of fuel ROME, further experiments were conducted at higher spray (injection) pressures of 500 bar, 625 bar, and 750 bar with varying ignition delay period via varying its spray timings such as 8°, 13°, 18°, 23°, 28°, and 33° before top dead center. Spray pressure 250 bar at 23° before top dead center was investigated as an optimistic operating condition where fuel rubber seed oil methyl ester gives negligible hydrocarbon emissions (0.019 g/kW h) while its nitrogen oxide (NOX) emissions were about 70% lesser than those observed with neat diesel, respectively.

Influence of Viscosity and Magnetoviscous Effect on the Performance of a Magnetic Fluid Seal in a Water Environment

2017 ◽  
Vol 61 (2) ◽  
pp. 367-375 ◽  
Author(s):  
Zhenkun Li ◽  
Decai Li ◽  
Yibiao Chen ◽  
Yilong Yang ◽  
Jie Yao
Keyword(s):  
Magnetic Fluid ◽  
Water Environment ◽  
Magnetoviscous Effect

Gas Cooling and Humidification: Design of Packed Towers from Small-Scale Tests

1950 ◽  
Vol 163 (1) ◽  
pp. 41-53 ◽  
Author(s):  
W. F. Carey ◽  
G. J. Williamson
Keyword(s):  
Operating Conditions ◽  
Total Heat ◽  
Small Scale ◽  
Water Cooling ◽  
Packed Tower ◽  
Simple Method ◽  
Worked Example ◽  
Gas Cooling ◽  
Heat Method ◽  
Working Out

On plants in which gases are processed, the gases are often brought into direct contact with water—usually in packed towers. The purpose may be to cool a hot gas, to increase the humidity of a gas, or, in the well-known special case of water-cooling towers, to cool water by contact with atmospheric air. These processes involve simultaneous transfers of sensible heat and water vapour, and existing methods of analysis are complex and laborious, except for the cooling of water, for which Merkel's total-heat method has long been available. Merkel's approximate solution offers the engineer a simple method of working out, for any operating conditions, the amount of heat transferred and the “driving force” available for transferring it. The present paper generalizes the total-heat method and, with a permissible sacrifice in accuracy, preserves the essential simplicity of the water-cooling treatment for gas-cooling and humidification processes. To complete the design of a packed tower, a knowledge is required of the characteristics of the packing. Information obtained in small towers is given for a number of packings, and a worked example shows how to apply the method of treatment, and the packing data presented, to the design of a large plant tower.

Convection in Magnetic Fluids With Internal Heat Generation

1991 ◽  
Vol 113 (1) ◽  
pp. 122-127 ◽  
Author(s):  
N. Rudraiah ◽  
G. N. Sekhar
Keyword(s):  
Heat Source ◽  
Uniform Distribution ◽  
Heat Generation ◽  
Magnetic Fluid ◽  
Fluid Layer ◽  
Internal Heat ◽  
Magnetic Fluids ◽  
Internal Heat Generation ◽  
Stationary Convection ◽  
Expansion Technique

The effect of a uniform distribution of heat source on the onset of stationary convection in a horizontal Boussinesq magnetic fluid layer bounded by isothermal nonmagnetic boundaries is investigated. Solutions are obtained using a higher order Galerkin expansion technique, considering different isothermal boundary combinations (rigid-rigid, rigid-free, and free-free). It is found that the effect of internal magnetic number, due to a heat source, is to make the system more unstable. The results obtained, in the limiting cases, compare well with the existing literature.

Experimental Investigation on the Rubbing Process of Labyrinth Seals Considering the Material Combination

2020 ◽  
Author(s):  
Lisa Hühn ◽  
Oliver Munz ◽  
Corina Schwitzke ◽  
Hans-Jörg Bauer
Keyword(s):  
Turbine Blades ◽  
Design Guidelines ◽  
Operating Conditions ◽  
Contact Forces ◽  
Experimental Investigations ◽  
Process Data ◽  
Labyrinth Seals ◽  
Material Combination ◽  
Higher Temperature ◽  
And Control

Abstract Labyrinth seals are used to prevent and control the mass flow rate between rotating components. Due to thermally and mechanically induced expansions during operation and transient flight maneuvers, a contact, the so-called rubbing process, between rotor and stator cannot be excluded. A large amount of rubbing process data concerning numerical and experimental investigations is available in public literature as well as at the Institute of Thermal Turbomachinery (ITS). The investigations were carried out for different operating conditions, material combinations, and component geometries. In combination with the experiments presented in this paper, the effects of the different variables on load due to rubbing are compared, and discussed with the focus lying on the material combination. The influence of the material on the loads can be identified as detailed as never before. For example, the contact forces in the current experiments are higher due to a higher temperature resistance of Young’s modulus. The analysis will also be based on the rubbing of turbine blades. Design guidelines are derived for labyrinth seals with improved properties regarding tolerance of rub events. Based on the knowledge obtained, guidelines for designing reliable labyrinth seals for future engines are discussed.

Experimental Inverstigations On the Pressure Fluctuations in the Sealing Gap of Dry Gas Seals with Embedded Pressure Sensors

2021 ◽  
Author(s):  
Jingjing Luo ◽  
Dieter Brillert
Keyword(s):  
High Speed ◽  
Gas Flow ◽  
Static Pressure ◽  
Pressure Sensors ◽  
Operating Conditions ◽  
Test Facility ◽  
Experimental Investigations ◽  
Mechanical Seals ◽  
Process Gas ◽  
Sealing Gap

Abstract Dry gas lubricated non-contacting mechanical seals (DGS), most commonly found in centrifugal compressors, prevent the process gas flow into the atmosphere. Especially when high speed is combined with high pressure, DGS is the preferred choice over other sealing alternatives. In order to investigate the flow field in the sealing gap and to facilitate the numerical prediction of the seal performance, a dedicated test facility is developed to carry out the measurement of key parameters in the gas film. Gas in the sealing film varies according to the seal inlet pressure, and the thickness of gas film depends on this fluctuated pressure. In this paper, the test facility, measurement methods and the first results of static pressure measurements in the sealing gap of the DGS obtained in the described test facility are presented. An industry DGS with three-dimensional grooves on the surface of the rotating ring, where experimental investigations take place, is used. The static pressure in the gas film is measured, up to 20 bar and 8,100 rpm, by several high frequency ultraminiature pressure transducers embedded into the stationary ring. The experimental results are discussed and compared with the numerical model programmed in MATLAB, the characteristic and magnitude of which have a good agreement with the numerical simulations. It suggests the feasibility of measuring pressure profiles of the standard industry DGS under pressurized dynamic operating conditions without altering the key components of the seal and thereby affecting the seal performance.

Corrosion Phenomena of Eurofeer Steel in Pb-17Li Stationary Flow at Magnetic Field

2006 ◽  
Author(s):  
E. Platacis ◽  
I. Bucenieks ◽  
F. Muktupavel ◽  
A. Shishko
Keyword(s):  
Magnetic Field ◽  
Structural Material ◽  
Corrosion Rate ◽  
Liquid Metals ◽  
Metal Flow ◽  
Stationary Flow ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Martensitic Steels ◽  
Eurofer 97

Search of new energy sources draws the increasing attention to use for this purpose of reactors. In the Europe some years the program EUROATOM uniting scientific of the many countries for the decision of constructive problems at designing of fusion reactors operates. One of the main things in this program is the problem of liquid metals breeder blanket behaviour. Structural material of blanket should meet high requirements because of extreme operating conditions. Therefore the knowledge of the effect of metals flow velocity, temperatures and also a neutron irradiation and a magnetic field on the corrosion processes are necessary. At the moment the eutectic lead -lithium (Pb-17Li) is considered as the most suitable tritium breeder material [1–3]. In turn as a structural material have been tested both many austenitic and ferritic-martensitic steels [2–4]. As the optimum variant is considered steel EUROFER 97, which corrosion rate in liquid Pb-17Li eutectic is the least [3,4]. However, these results have been received without taking into account influence of a strong magnetic field. At the same time, this influence should be essential, as because of change of hydrodynamics of a liquid metal flow, and because of interaction of a magnetic field with a ferromagnetic steel. It has been shown in [5,6] that the magnetic field leads to increase of corrosion rate for austenitic (316L) and martensitic (1,4914) steels. Experimental data for EUROFER 97, and also a theoretical substantiation of the phenomenon are absent, that creates essential difficulties for forecasting working capacity of blanket construction. The aim of presented work were the theoretical and experimental investigations of magnetic field influence on the corrosion of EUROFER 97 steel exposed to flowing Pb-17 Li in specific designed loop.

Sign in / Sign up

Export Citation Format

Share Document