Solid Phase Excitation-Emission Matrix Spectroscopy for In-Situ Chemical Analysis of Combustion Aerosols

2020 ◽  
Author(s):  
Gaurav Mahamuni ◽  
Jiayang He ◽  
Jay Rutherford ◽  
Byron Ockerman ◽  
Edmund Seto ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Cigarette Smoke ◽  
Forest Fires ◽  
Solid Phase ◽  
Incident Angle ◽  
Personal Exposure ◽  
Traffic Emission ◽  
Excitation Emission Matrix ◽  
Internal Excitation

<p>Exposure to combustion generated aerosols such as PM from residential woodburning, forest fires, cigarette smoke, and traffic emission have been linked to adverse health outcomes. It is important to assess the chemical composition of PM to examine personal exposure. Excitation-emission matrix (EEM) spectroscopy has been shown as a sensitive and cost-effective technique for evaluation of combustion PM composition and as a source apportionment tool. However, EEM measurements are hindered by a solvent extraction step and a need for benchtop instrumentation. Here, we present a methodology that eliminates this labor-intensive sample preparation and allows to automate and miniaturize the detection platform. A miniature electrostatic collector deposits PM sample onto transparent polydimethylsiloxane (PDMS) coated substrate, where PAH components are extracted into solid-phase (SP) solvent and analyzed using EEM spectroscopy in-situ. We evaluated external and internal excitation schemes to optimized signal to noise ratio. Analysis of woodsmoke and cigarette smoke samples showed good agreement with liquid extraction EEM spectra. Internal excitation is hindered by fluorescent interference from PDMS at λ<250nm. The external excitation EEM spectra are dependent on the incident angle; ranges of 30-40⁰ and 55-65⁰ showed the best results. The proposed SP-EEM technique can be used for development of miniaturized sensors for chemical analysis of combustion generated PM. </p>

Solid Phase Excitation-Emission Matrix Spectroscopy for In-Situ Chemical Analysis of Combustion Aerosols

2020 ◽  
Author(s):  
Gaurav Mahamuni ◽  
Jiayang He ◽  
Jay Rutherford ◽  
Byron Ockerman ◽  
Edmund Seto ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Cigarette Smoke ◽  
Forest Fires ◽  
Solid Phase ◽  
Incident Angle ◽  
Personal Exposure ◽  
Traffic Emission ◽  
Excitation Emission Matrix ◽  
Internal Excitation

<p>Exposure to combustion generated aerosols such as PM from residential woodburning, forest fires, cigarette smoke, and traffic emission have been linked to adverse health outcomes. It is important to assess the chemical composition of PM to examine personal exposure. Excitation-emission matrix (EEM) spectroscopy has been shown as a sensitive and cost-effective technique for evaluation of combustion PM composition and as a source apportionment tool. However, EEM measurements are hindered by a solvent extraction step and a need for benchtop instrumentation. Here, we present a methodology that eliminates this labor-intensive sample preparation and allows to automate and miniaturize the detection platform. A miniature electrostatic collector deposits PM sample onto transparent polydimethylsiloxane (PDMS) coated substrate, where PAH components are extracted into solid-phase (SP) solvent and analyzed using EEM spectroscopy in-situ. We evaluated external and internal excitation schemes to optimized signal to noise ratio. Analysis of woodsmoke and cigarette smoke samples showed good agreement with liquid extraction EEM spectra. Internal excitation is hindered by fluorescent interference from PDMS at λ<250nm. The external excitation EEM spectra are dependent on the incident angle; ranges of 30-40⁰ and 55-65⁰ showed the best results. The proposed SP-EEM technique can be used for development of miniaturized sensors for chemical analysis of combustion generated PM. </p>

scholarly journals Solid-phase excitation-emission matrix spectroscopy for chemical analysis of combustion aerosols

PLoS ONE ◽  
2021 ◽  
Vol 16 (5) ◽  
pp. e0251664
Author(s):  
Gaurav Mahamuni ◽  
Jiayang He ◽  
Jay Rutherford ◽  
Byron Ockerman ◽  
Arka Majumdar ◽  
...  
Keyword(s):  
Liquid Phase ◽  
Cigarette Smoke ◽  
Forest Fires ◽  
Solid Phase ◽  
Organic Fraction ◽  
Excitation Light ◽  
Excitation Emission Matrix ◽  
Internal Excitation ◽  
Combustion Aerosols

Exposure to ultrafine combustion aerosols such as particulate matter (PM) from residential woodburning, forest fires, cigarette smoke, and traffic emission have been linked to adverse health outcomes. Excitation-emission matrix (EEM) spectroscopy presents a sensitive and cost-effective alternative for analysis of PM organic fraction. However, as with other analytical chemistry methods, the miniaturization is hindered by a solvent extraction step and a need for benchtop instrumentation. We present a methodology for collecting and in-situ analysis of airborne nanoparticles that eliminates labor-intensive sample preparation and miniaturizes the detection platform. Nanoparticles are electrostatically collected onto a transparent substrate coated with solid-phase (SP) solvent—polydimethylsiloxane (PDMS). The PM organic fraction is extracted into PDMS and analyzed in-situ, thus avoiding liquid-phase extraction. In the SP-EEM analysis, we evaluated external and internal excitation schemes. Internal excitation shows the lowest scattering interference but leads to signal masking from PDMS fluorescence for λ<250nm. The external excitation EEM spectra are dependent on the excitation light incident angle; ranges of 30–40° and 55–65° show the best results. SP-EEM spectra of woodsmoke and cigarette smoke samples are in good agreement with the EEM spectra of liquid-phase extracts. The SP-EEM technique can be used to develop wearable sensors for exposure assessments and environmental monitoring.

Dynamic studies of silicide-mediated crystallization of amorphous silicon

1992 ◽  
Vol 50 (2) ◽  
pp. 1352-1353
Author(s):  
C. Hayzelden ◽  
J. L. Batstone
Keyword(s):  
Ion Implantation ◽  
Solid Phase ◽  
Metallic Phase ◽  
Single Crystal Substrate ◽  
Free Electrons ◽  
Melt Temperature ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
High Resolution Tem

Epitaxial reordering of amorphous Si(a-Si) on an underlying single-crystal substrate occurs well below the melt temperature by the process of solid phase epitaxial growth (SPEG). Growth of crystalline Si(c-Si) is known to be enhanced by the presence of small amounts of a metallic phase, presumably due to an interaction of the free electrons of the metal with the covalent Si bonds near the growing interface. Ion implantation of Ni was shown to lower the crystallization temperature of an a-Si thin film by approximately 200°C. Using in situ transmission electron microscopy (TEM), precipitates of NiSi2 formed within the a-Si film during annealing, were observed to migrate, leaving a trail of epitaxial c-Si. High resolution TEM revealed an epitaxial NiSi2/Si(l11) interface which was Type A. We discuss here the enhanced nucleation of c-Si and subsequent silicide-mediated SPEG of Ni-implanted a-Si.Thin films of a-Si, 950 Å thick, were deposited onto Si(100) wafers capped with 1000Å of a-SiO2. Ion implantation produced sharply peaked Ni concentrations of 4×l020 and 2×l021 ions cm−3, in the center of the films.

Growth of Epitaxial IrSi3 Layers on Si(111)

1989 ◽  
Vol 160 ◽  
Author(s):  
T. L. Lin ◽  
C. W. Nieh
Keyword(s):  
Surface Morphology ◽  
Molecular Beam ◽  
Solid Phase ◽  
Single Mode ◽  
Growth Conditions ◽  
Tem Analysis ◽  
Mbe Growth ◽  
Good Surface ◽  
Transmission Electron

AbstractEpitaxial IrSi3 films have been grown on Si (111) by molecular beam epitaxy (MBE) at temperatures ranging from 630 to 800 °C and by solid phase epitaxy (SPE) at 500 °C. Good surface morphology was observed for IrSi3 layers grown by MBE at temperatures below 680 °C, and an increasing tendency to form islands is noted in samples grown at higher temperatures. Transmission electron microscopy (TEM) analysis reveals that the IrSi3 layers grow epitaxially on Si(111) with three epitaxial modes depending on the growth conditions. For IrSi3 layers grown by MBE at 630 °C, two epitaxial modes were observed with ~ 50% area coverage for each mode. Single mode epitaxial growth was achieved at a higher MBE growth temperature, but with island formation in the IrSi3 layer. A template technique was used with MBE to improve the IrSi3 surface morphology at higher growth temperatures. Furthermore, single-crystal IrSi3 was grown on Si(111) at 500 °C by SPE, with annealing performed in-situ in a TEM chamber.

PFAS removal from wastewater by in-situ formed ferric nanoparticles: Solid phase loading and removal efficiency

2021 ◽  
Vol 9 (4) ◽  
pp. 105452
Author(s):  
Jianhua Zhang ◽  
Hongjiao Pang ◽  
Stephen Gray ◽  
Shaoheng Ma ◽  
Zongli Xie ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Solid Phase

scholarly journals Solid-Phase Extraction Embedded Dialysis (SPEED), an Innovative Procedure for the Investigation of Microbial Specialized Metabolites

Marine Drugs ◽  
2021 ◽  
Vol 19 (7) ◽  
pp. 371
Author(s):  
Phuong-Y Mai ◽  
Géraldine Le Goff ◽  
Erwan Poupon ◽  
Philippe Lopes ◽  
Xavier Moppert ◽  
...  
Keyword(s):  
Solid Phase Extraction ◽  
Solid Phase ◽  
Chemical Space ◽  
Molecular Profile ◽  
Phase Extraction ◽  
Specialized Metabolites ◽  
Streptomyces Albidoflavus ◽  
Cultivation Process ◽  
The Impact

Solid-phase extraction embedded dialysis (SPEED technology) is an innovative procedure developed to physically separate in-situ, during the cultivation, the mycelium of filament forming microorganisms, such as actinomycetes and fungi, and the XAD-16 resin used to trap the secreted specialized metabolites. SPEED consists of an external nylon cloth and an internal dialysis tube containing the XAD resin. The dialysis barrier selects the molecular weight of the trapped compounds, and prevents the aggregation of biomass or macromolecules on the XAD beads. The external nylon promotes the formation of a microbial biofilm, making SPEED a biofilm supported cultivation process. SPEED technology was applied to the marine Streptomyces albidoflavus 19-S21, isolated from a core of a submerged Kopara sampled at 20 m from the border of a saltwater pond. The chemical space of this strain was investigated effectively using a dereplication strategy based on molecular networking and in-depth chemical analysis. The results highlight the impact of culture support on the molecular profile of Streptomyces albidoflavus 19-S21 secondary metabolites.

scholarly journals Fe3O4@C Nanoparticles Synthesized by In Situ Solid-Phase Method for Removal of Methylene Blue

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 330
Author(s):  
Hengli Xiang ◽  
Genkuan Ren ◽  
Yanjun Zhong ◽  
Dehua Xu ◽  
Zhiye Zhang ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Solid Phase ◽  
Raw Materials ◽  
Phase Method ◽  
Maximum Adsorption Capacity ◽  
High Catalytic Activity ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
High Concentrations

Fe3O4@C nanoparticles were prepared by an in situ, solid-phase reaction, without any precursor, using FeSO4, FeS2, and PVP K30 as raw materials. The nanoparticles were utilized to decolorize high concentrations methylene blue (MB). The results indicated that the maximum adsorption capacity of the Fe3O4@C nanoparticles was 18.52 mg/g, and that the adsorption process was exothermic. Additionally, by employing H2O2 as the initiator of a Fenton-like reaction, the removal efficiency of 100 mg/L MB reached ~99% with Fe3O4@C nanoparticles, while that of MB was only ~34% using pure Fe3O4 nanoparticles. The mechanism of H2O2 activated on the Fe3O4@C nanoparticles and the possible degradation pathways of MB are discussed. The Fe3O4@C nanoparticles retained high catalytic activity after five usage cycles. This work describes a facile method for producing Fe3O4@C nanoparticles with excellent catalytic reactivity, and therefore, represents a promising approach for the industrial production of Fe3O4@C nanoparticles for the treatment of high concentrations of dyes in wastewater.

Sign in / Sign up

Export Citation Format

Share Document