scholarly journals Alkali Lignin from Rice (Oryza sativa L.) Husk as Adsorbent for Aqueous Methyl Orange and Bromothymol Blue: Analysis of the Adsorption Kinetics and Mechanism

KIMIKA ◽  
2021 ◽  
Vol 32 (1) ◽  
pp. 19-33
Author(s):  
Marjorie Pearl Linde ◽  
Kevinilo Marquez
Keyword(s):  
Oryza Sativa ◽  
Methyl Orange ◽  
Contact Time ◽  
Oryza Sativa L ◽  
Removal Rate ◽  
Bromothymol Blue ◽  
Isotherm Models ◽  
Adsorption Model ◽  
Adsorption Processes ◽  
Pseudo Second Order

In this study, lignin was isolated from rice (Oryza sativa L.) husk using alkaline extraction method and was used as an adsorbent for aqueous solutions of methyl orange (MO) and bromothymol blue (BTB). The equilibrium removal rate of MO was found to be at 61.4%, with experimental equilibrium adsorbate uptake, qe, of 1.23 mg·g-1, achieved at 150 minutes contact time. For BTB, the equilibrium removal rate was found to be at 78.3%, with an experimental qe of 1.57 mg·g-1, achieved at 150 minutes contact time. Pseudo-first order (PFO) and pseudo-second order (PSO) kinetic models were then used to investigate the kinetics of the adsorption process. Both MO and BTB on lignin were found to follow a PSO kinetic model, with rates of 6.84 x 10-3 g·mg-1·min-1 and 0.69 g·mg-1·min-1, respectively. Langmuir, Freundlich, Dubinin-Radushkevich (DR), Brunauer-Emmett-Teller (BET), Flory Huggins (FH), and Temkin adsorption isotherm models were then used to determine the appropriate equilibrium adsorption model for both substrates. Based on the calculations performed, the Temkin model best described the adsorptive removal of both MO and BTB. Based on the Temkin model, the adsorption processes of both MO and BTB were found to occur spontaneously, with equilibrium rate constants of 0.083 L·mg-1 and 0.012 L·mg-1, respectively.  

Adsorption of 2,4,6-trichlorophenol on bentonite modified with benzyldimethyltetradecylammonium chloride

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Infrared Spectroscopy ◽  
Contact Time ◽  
Removal Rate ◽  
Organic Pollutant ◽  
Freundlich Isotherm ◽  
Solution Concentration ◽  
Isotherm Models ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pseudo Second Order

The objective of this study is to evaluate the performance and capacities of the bentonite of Maghnia, modified with benzyldimethyltetradecylammonium chloride, to remove the organic pollutant 2,4,6-Trichlorophenol (TCP). The modified sample was studied by X-ray diffraction (XRD) technique, infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) methods. The best removal rate (99.52%) was obtained at 19°C, pH 4, solution concentration of 50 mg/L, stirring speed of 180 rpm and contact time of 60 min. The results were well fitted by both Langmuir and Freundlich isotherm models and the pseudo-second-order is the best model to describe the process.

scholarly journals Study of the Digestate as an Innovative and Low-Cost Adsorbent for the Removal of Dyes in Wastewater

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 852
Author(s):  
Sicong Yao ◽  
Massimiliano Fabbricino ◽  
Marco Race ◽  
Alberto Ferraro ◽  
Ludovico Pontoni ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Contact Time ◽  
Removal Rate ◽  
Low Cost ◽  
Second Order ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Diffusion Kinetic ◽  
Pseudo Second Order

Digestate, as an urban solid waste, was considered as an innovative adsorbent for colorant polluted wastewater. Batch adsorption experiments were carried out using digestate as an adsorbent material to remove various dyes belonging to different categories. The removal rate and adsorption capacity of dyes were evaluated and the dose of digestate, contact time, and initial dye concentration were studied. The maximum removal rate was approximately 96% for Methylene Blue. The equilibrium time for the Methylene Blue was 4 h, while for other dyes, a longer contact time was required to reach the equilibrium. The suspicion of colloidal matter release into the solution from solid fraction of the digestate led to the investigation of the consequence of a washing step of the digestate adsorbent upstream the adsorption experiment. Washed and not washed adsorbents were tested and the differences between them in terms of dye removal were compared. Moreover, experimental data were fitted by pseudo-first order, pseudo-second order, and intra-partial diffusion kinetic models as well as Langmuir, Freundlich, and Sips isotherm models. The results from fitted models showed that the adsorption of various dyes onto the digestate was mostly well fitted by the Langmuir isotherm and pseudo-second-order kinetic model.

Chromium (VI) adsorption onto activated sulfate lignin

2009 ◽  
Vol 4 (2) ◽  
Author(s):  
Nassima Tazrouti ◽  
Moussa Amrani
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Analytical Data ◽  
Order Equation ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Adsorption Model ◽  
Chromium Vi ◽  
Pseudo Second Order

Activated lignin having surface area of 1023 m2.g-1 has been prepared from sulfate lignin that was treated by 30 % H2O2 and carbonized at 300 °C in order to test the chromium (VI) adsorption from aqueous solution. The influence of contact time, pH, initial concentration of adsorbent and adsorbate and temperature on the adsorption capacity were investigated. The maximum removal of Cr(VI) was found to be 92,36 % at pH=2 and contact time of 80 min. Optimal concentration of lignin and Cr(VI) were found to be 3.8 g.l-1 and 180 mg.l-1, respectively. The adsorption kinetics was tested pseudo-first-order and pseudo-second-order equation. The analytical data were fitted well in a pseudo-second-order equation and the rate of removal of chromium was found to speed up with increasing temperature. Activation energy for the adsorption process was found to be 18.19 Kj.mol-1. The Langmuir and Freundlich adsorption isotherm models were applied to describe the isotherm and isotherm constants for the adsorption of Cr (VI) on lignin. These constants and correlation coefficients of the isotherm models were calculated and compared. Results indicated that Cr (VI) uptake could be described by the Langmuir adsorption model. The maximum adsorption capacity (qm) of Cr (VI) on lignin was 75.75 mg.g-1 at temperature of 40°C. The dimensionless equilibrium parameter (RL) signified a favorable adsorption of Cr (VI) on lignin and was found between 0.0601 and 0.818 (0<RL<1). The thermodynamic parameters like ΔG°, ΔS° and ΔH° were calculated and it has been found that the reaction was spontaneous and endothermic in nature. This study indicates that lignin has the potential to become an effective and economical adsorbent for removal Cr (VI) from the waste water.

scholarly journals Efficient Removal of Methyl Orange from Wastewater by Polymeric Chitosan-iso-vanillin

2020 ◽  
Vol 7 (1) ◽  
pp. 16-25
Author(s):  
Eman A. Alabbad
Keyword(s):  
Water Pollution ◽  
Methyl Orange ◽  
Contact Time ◽  
Removal Rate ◽  
Second Order ◽  
Rate Equations ◽  
Order Kinetic ◽  
Solution Ph ◽  
Modified Chitosan ◽  
Pseudo Second Order

Introduction: Water pollution is a serious issue in several countries. In addition, because of limited water resources, the recycling of wastewater is crucial. Consequently, new and effective sorbents are required to reduce the cost of wastewater treatment as well as to mitigate the health problems caused by water pollution. Methods: In this study, the removal of Methyl Orange (MO) dye from wastewater using a chitosan-iso-vanillin polymer was evaluated. The removal of MO from an aqueous solution was studied in a batch system, using the modified chitosan polymer. Results: The results indicate that the removal of MO by the modified chitosan was affected by the solution pH, sorbent dosage, initial MO concentration, contact time, and temperature. The experimental data were fitted to the Langmuir, Freundlich, and Temkin isotherms, and Freundlich isotherm showed the best fit. The kinetic data were fitted to the pseudo-first-order and pseudo-second-order rate equations. Thus, the removal of MO was controlled via chemisorption, and the removal rate was 97.9% after 3 h at an initial MO concentration of 100 ppm and a sorbent dose of 0.05 g. The adsorption behavior of the modified chitosan for the removal of MO was well-described using the pseudo-second-order kinetic model. Intraparticle diffusion analysis was also conducted, and the thermodynamic properties, including entropy (∆S), enthalpy (∆H), and free energy (∆G), were determined. Conclusion: The pH, initial MO concentration, sorbent dosage, adsorption temperature, and contact time had a significant effect on the adsorption of MO by chitosan-iso-vanillin.

Kinetic Study of Methyl Orange Adsorption from Solution by IOCZ

2013 ◽  
Vol 684 ◽  
pp. 194-197
Author(s):  
Yi Ke Li ◽  
Bing Lu Zhao ◽  
Wei Xiao ◽  
Run Ping Han ◽  
Yan Qiang Li
Keyword(s):  
Methyl Orange ◽  
Contact Time ◽  
Adsorption Mechanism ◽  
Order Model ◽  
Initial Concentration ◽  
Pseudo Second Order ◽  
Adsorption From Solution ◽  
Adsorption Quantity ◽  
Regressive Analysis

The effect of contact time and the determination of the kinetic parameters of adsorption of methyl orange (MO) from aqueous solution onto Iron-Oxide-Coated-Zeolite (IOCZ) powder are important in understanding the adsorption mechanism. The effect of contact time on adsorption quantity was studied at different initial concentration and temperature, respectively. The pseudo-second-order model was adopted to fit the experimental data using non-linear regressive analysis and it was used to predict the adsorption behavior. The results showed that the process of adsorption MO was endothermic and chemisorption. The pore diffusion was not significant.

Characterization and adsorption performance of chitosan/diatomite membranes for Orange G removal

e-Polymers ◽  
2016 ◽  
Vol 16 (2) ◽  
pp. 99-109 ◽  
Author(s):  
Xiu-Juan Wu ◽  
Ji-De Wang ◽  
Li-Qin Cao
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Ph Value ◽  
Removal Rate ◽  
Composite Membranes ◽  
Second Order ◽  
Inorganic Substances ◽  
Phase Inversion Technique ◽  
Orange G ◽  
Pseudo Second Order

AbstractNovel chitosan/diatomite (CS/DM) membranes were prepared by phase inversion technique to remove anionic azo dyes from wastewater. The fabricated composite membranes exhibited the combined advantages of inorganic substances, diatomites, and polysaccharides. These composite membranes were characterized through Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction analysis. The mechanical properties of the membranes were also evaluated. Adsorption experiments were conducted under varied initial dye concentration, solution pH values, contact time, and adsorbent dosage. The results indicate that pH 3 is the optimal pH value for Orange G adsorption. The CS/DM membranes exhibit the highest adsorption capacity of 588 mg g-1 and removal rate of 94% under an initial dye concentration of 200 mg l-1, contact time of 6 h, and membrane dosage of 8 mg. Langmuir, Freundlich and Redlich-Peterson adsorption models were applied to describe the equilibrium isotherms at different dye concentrations. The equilibrium data was found to be fitted well to the Redlich-Peterson isotherm. Pseudo-first-order and pseudo-second-order kinetics models were used to describe the adsorption of membranes. The adsorption data were well explained by pseudo-second-order models, and also followed by the Elovich model. In addition, these membranes display high adsorption capacity and mechanical performance even after reused for seven times.

Removal of acetaminophen (ACT) from aqueous solution by using nanosilica adsorbent: experimental study, kinetic and isotherm modeling

2020 ◽  
Vol 49 (1) ◽  
pp. 55-62
Author(s):  
Akbar Eslami ◽  
Zahra Goodarzvand Chegini ◽  
Maryam Khashij ◽  
Mohammad Mehralian ◽  
Marjan Hashemi
Keyword(s):  
Removal Rate ◽  
Synthesis Method ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Content Type ◽  
Bet Analysis ◽  
Pseudo Second Order

Purpose A nanosilica adsorbent was prepared and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET. Design/methodology/approach The optimum conditions for the highest adsorption performance were determined by kinetic modeling. The adsorbent was used for the adsorption of acetaminophen (ACT), and the parameters affecting the adsorption were discussed like pH, initial concentration, contact time and adsorbent dosage. The adsorbent have been characterized by SEM, XRD and BET analysis. The kinetic models including pseudo-first-order and pseudo-second-order with Langmuir and Freundlich isotherm models were applied to investigate the kinetic and isotherms parameters. Findings The adsorption of ACT increased to around 95% with the increase of nanosilica concentration to 30 g/L. Moreover, the adsorption process of ACT follows the pseudo-second-order kinetics and the Langmuir isotherm with the maximum adsorption capacity of 609 mg/g. Practical implications This study provided a simple and effective way to prepare of nanoadsorbents. This way was conductive to protect environmental and subsequent application for removal of emerging pollutants from aqueous solutions. Originality/value The novelty of the study is synthesizing the morphological and structural properties of nanosilica-based adsorbent (specific surface area, pore volume and size, shape and capability) and improving its removal rate through optimizing the synthesis method; and studying the capability of synthesis of nanosilica-based adsorbent for removal of ACT as a main emerging pharmaceutical water contaminant.

scholarly journals Characterization and Evaluation of Zeolite A/Fe3O4 Nanocomposite as a Potential Adsorbent for Removal of Organic Molecules from Wastewater

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Emmanuel Nyankson ◽  
Jonas Adjasoo ◽  
Johnson Kwame Efavi ◽  
Reuben Amedalor ◽  
Abu Yaya ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Isotherm Models ◽  
Adsorption Efficiency ◽  
Ferrous Chloride ◽  
X Ray ◽  
Intraparticle Diffusion Model ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Chloride Salts

In this work, zeolite (Z) and Z-Fe3O4 nanocomposite (Z-Fe3O4 NC) have been synthesized. The Fe3O4 nanoparticles were synthesized using the extract from maize leaves and ferric and ferrous chloride salts and encapsulated into the zeolite framework. The nanocomposite (Z-Fe3O4 NC) was characterized using X-ray diffractometer (XRD), Fourier-transform infrared (FT-IR) spectroscopy, energy-dispersive X-ray (EDX) spectroscopy, and scanning electron microscopy (SEM). The potential of Z-Fe3O4 NC as an adsorbent for removing methylene blue molecules (MB) from solution was examined using UV-Vis and kinetic and equilibrium isotherm models. The adsorption data fitted best with the pseudo-second-order model and Weber and Morris model, indicating that the adsorption process was chemisorption, while the Weber and Morris described the rate-controlling steps. The intraparticle diffusion model suggests that the adsorption processes were pore and surface diffusion controlled. The Langmuir isotherm model best describes the adsorption process indicating homogeneous monolayer coverage of MB molecules onto the surface of the Z-Fe3O4 NC. The maximum Langmuir adsorption capacity was 2.57 mg/g at 25°C. The maximum adsorption efficiency was 97.5%. After regeneration, the maximum adsorption efficiency achieved at a pH of 7 was 82.6%.

scholarly journals Adsorption of Nickel and Chromium From Aqueous Solutions Using Copper Oxide Nanoparticles: Adsorption Isotherms, Kinetic Modeling, and Thermodynamic Studies

2019 ◽  
Vol 6 (2) ◽  
pp. 66-74 ◽  
Author(s):  
Raziyeh Hosseini ◽  
Mohammad Hossein Sayadi ◽  
Hossein Shekari
Keyword(s):  
Aqueous Solutions ◽  
Copper Oxide ◽  
Removal Efficiency ◽  
Contact Time ◽  
Removal Rate ◽  
Copper Oxide Nanoparticles ◽  
Isotherm Models ◽  
Oxide Nanoparticles ◽  
Initial Concentration ◽  
Adsorbent Dosage

The research was conducted with an aim to assess the efficiency of copper oxide nanoparticles as an adsorbent to remove Ni and Cr. The effect of pH, adsorbent dosage, contact time, initial concentration of metals (Ni and Cr) on the adsorption rate was evaluated and removal of these elements from aqueous solutions was measured using Atomic Absorption Spectrum System (Conter AA700). Moreover, the kinetic and isotherm besides thermodynamic adsorption models were assessed. The highest Ni and Cr removal rate occurred at an optimal pH of 7, and an initial concentration of 30 mg/L, a time period of 30 minutes, and 1 g/L of copper oxide nanoparticles. In fact, with the increase of adsorbent dosage and contact time, the removal efficiency increased and with initial concentration increase of Ni and Cr ions, the removal efficiency reduced. The correlation coefficient of isotherm models viz. Langmuir, Freundlich, Temkin, Redlich-Peterson, and Koble-Corrigan showed that Ni and Cr adsorption via copper oxide nanoparticles better follows the Langmuir model in relation to other models. The results showed that kinetic adsorption of Ni and Cr via copper oxide nanoparticles follows the second order pseudo model with correlation coefficients above 0.99. In addition, the achieved thermodynamic constants revealed that the adsorption process of metals (i.e., Ni and Cr) via copper oxide nanoparticles was endothermic and spontaneous and the reaction enthalpy values for these metals were 17.727 and 11.862 kJ/mol, respectively. In conclusion, copper oxide nanoparticles can be used as effective and environmentally compatible adsorbents to remove Ni and Cr ions from the aqueous solutions

scholarly journals Biosorption of Cr(III) from aqueous solution using an agricultural by-product jute stick powder: Equilibrium and kinetic studies

2018 ◽  
Vol 9 (3) ◽  
pp. 202-212 ◽  
Author(s):  
Mohammad Nasir Uddin ◽  
Jahangir Alam ◽  
Syeda Rahimon Naher
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Metal Ion ◽  
Water Solution ◽  
Low Cost ◽  
Isotherm Models ◽  
Infrared Spectrometry ◽  
Order Kinetic ◽  
Adsorption Model ◽  
Experimental Conditions

The adsorption capacity of chromium(III) from synthetic waste water solution by a low cost biomaterial, Jute Stick Powder (JSP)was examined. A series of batch experiments were conducted at different pH values, adsorbent dosage and initial chromium concentration to investigate the effects of these experimental conditions. To analyze the metal adsorption on to the JSP, most common adsorption isotherm models were applied. To study the reaction rate, the kinetic and diffusion models were also applied. The morphological structure and variation of functional groups in the JSP before and after adsorption was examined by scanning electron microscope (SEM) and Fourier transform infrared spectrometry (FT-IR). Maximum chromium removal capacities of JSP was 84.34%with corresponding equilibrium uptake 8.4 mg/g from 50 mg/L of synthetic metal solution in 60 minutes of contact time at pH = 6.0 and 28 °C with continuous stirring at 180 rpm. The percent sorption of the biomass decreased with increasing concentration of metal ion but increased with decreasing pH, increasing contact time and adsorbent doses. Data for this study indicated a good correspondence with both isotherms of Langmuir and Freundlich isotherm. The analysis of kinetic indicated that Chromium was consistent with the second-order kinetic adsorption model. The rate of removal of Cr(III) ions from aqueous solution by JSP was found rapid initially within 5-30 minutes and reached in equilibrium in about 40 minutes. The investigation revealed that JSP, a low cost agricultural byproduct, was a potential adsorbent for removal of heavy metal ions from aqueous solution.

Sign in / Sign up

Export Citation Format

Share Document