scholarly journals ADSORPTION PROPERTIES OF TITANIA-SILICA MEMBRANES OBTAINED ON CERAMIC SUBSTRАTE

2018 ◽  
Vol 54 (3) ◽  
pp. 274-280
Author(s):  
T. F. Kouznetsova ◽  
A. I. Ivanets ◽  
J. D. Sauka
Keyword(s):  
Surface Area ◽  
Quartz Substrate ◽  
Cetylpyridinium Chloride ◽  
Nitrogen Adsorption ◽  
Mesoporous Structure ◽  
Adsorption Properties ◽  
Molar Ratio ◽  
Silica Membranes ◽  
Metal Silicate ◽  
Adsorption Desorption

Titania-silica membranes on a porous quartz substrate are prepared by its direct contact with metal silicate sol at various Ti/Si ratios in the conditions of coagel sedimentation and presence of cetylpyridinium chloride. The study of textural and adsorption properties of membranes is conducted by low-temperature nitrogen adsorption-desorption, including methods of t-plots and DFT theory. It was shown that obtained membranes have mesoporous structure with the specific surface area and pore hydraulic diameter varied in intervals of 64–217 m2 /g and 4–11 nm, respectively. Developed values of surface area remain up to molar ratio of Ti/Si = 50/50.

Synthesis and Structural Characterization of SiO2-Al2O3 Xerogels

2007 ◽  
Vol 336-338 ◽  
pp. 2286-2289
Author(s):  
Fei He ◽  
Xiao Dong He ◽  
Yao Li
Keyword(s):  
Structural Change ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
Mesoporous Structure ◽  
Supercritical Drying ◽  
High Specific Surface Area ◽  
Molar Ratio

Low-density xSiO2-(1-x)Al2O3 xerogels with x=0.9, 0.8, 0.7, 0.6 (mole fractions) were prepared by sol-gel and non-supercritical drying. Silica alkogels, which were the framework of binary composite materials, formed from tetraethyl orthosilicate (TEOS) by hydrolytic condensation with a molar ratio of TEOS: H2O: alcohol: hydrochloric acid: ammonia =1: 4: 10: 7.5×10-4: 0.0375. Aluminum hydroxide derived from Al(NO3)3·9H2O and NH4OH acting in the alcohol solution under the condition of catalyst. After filtrating and washing, the precipitation was mixed into silica sols to form SiO2-Al2O3 mixed oxide gels with different silicon and aluminum molar ratio. The structural change and crystallization of the binary xerogels were investigated after heat treatment at 600 for 2 h by the means of X-ray diffraction. Nitrogen adsorption experiment was performed to estimate specific surface area, porous volume and pore size distribution. The structural change of xerogels was observed by FT-IR spectroscopy. The resulting mixed xerogels possess of mesoporous structure which is characteristic of cylindrical pores, high specific surface area of 596-863 m2/g and a relatively narrow pore distribution of 2.8-30 nm. Al2O3 is introduced into the SiO2 phase and some of Al-O-Si bonds form.

Effect of Carbon Pre-Treatment on Pd Dispersion in Synthesis of Pd/C Catalyst

2014 ◽  
Vol 804 ◽  
pp. 149-152 ◽  
Author(s):  
Ji Sun Kim ◽  
Jae Ho Baek ◽  
Myung Hwan Kim ◽  
Seong Soo Hong ◽  
Man Sig Lee
Keyword(s):  
Surface Area ◽  
Nitrogen Adsorption ◽  
Area Ratio ◽  
High Dispersion ◽  
Co Chemisorption ◽  
Pd Dispersion ◽  
Before And After ◽  
Pre Treatment ◽  
Treated Carbon ◽  
Adsorption Desorption

In this study, we confirmed effect of carbon pre-treatment on Pd dispersion in synthesis of Pd/C catalyst. Physical characteristics on the surface of before and after pre-treated carbon were analyzed by nitrogen adsorption-desorption analysis. The dispersion and size of Pd particles were analyzed by XRD, FE-TEM and CO-chemisorption. After pre-treatment, surface area of carbon were decreased. And mesopore area ratio were increased with decreasing micropore area ratio. In the case of pre-treated carbon, we confirmed high dispersion of Pd particles.

Texture Evaluation of Sol-Gel Derived Mesoporous Bioactive Glass

2013 ◽  
Vol 284-287 ◽  
pp. 230-234
Author(s):  
Yu Jen Chou ◽  
Chi Jen Shih ◽  
Shao Ju Shih
Keyword(s):  
Surface Area ◽  
Calcination Temperature ◽  
High Surface ◽  
Sol Gel ◽  
High Surface Area ◽  
Nitrogen Adsorption ◽  
Bioactive Glasses ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Adsorption Desorption

Recent years mesoporous bioactive glasses (MBGs) have become important biomaterials because of their high surface area and the superior bioactivity. Various studies have reported that when MBGs implanted in a human body, hydroxyl apatite layers, constituting the main inorganic components of human bones, will form on the MBG surfaces to increase the bioactivity. Therefore, MBGs have been widely applied in the fields of tissue regeneration and drug delivery. The sol-gel process has replaced the conventional glasses process for MBG synthesis because of the advantages of low contamination, chemical flexibility and lower calcination temperature. In the sol-gel process, several types of surfactants were mixed with MBG precursor solutions to generate micelle structures. Afterwards, these micelles decompose to form porous structures after calcination. Although calcination is significant for contamination, crystalline and surface area in MBG, to the best of the authors’ knowledge, only few systematic studies related to calcination were reported. This study correlated the calcination parameters and the microstructure of MBGs. Microstructure evaluation was characterized by transmission electron microscopy and nitrogen adsorption/desorption. The experimental results show that the surface area and the pore size of MBGs decreased with the increasing of the calcination temperature, and decreased dramatically at 800°C due to the formation of crystalline phases.

Synthesis of Novel Core-Shell Structured Hydroxyapatite/Meso-Silica for Removal of Methylene Blue from Aqueous Solutions

2012 ◽  
Vol 463-464 ◽  
pp. 543-547 ◽  
Author(s):  
Cheng Feng Li ◽  
Xiao Lu Ge ◽  
Shu Guang Liu ◽  
Fei Yu Liu
Keyword(s):  
Methylene Blue ◽  
Aqueous Solutions ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Low Cost ◽  
Nitrogen Adsorption ◽  
Precipitation Method ◽  
Core Shell ◽  
Adsorption Desorption

Core-shell structured hydroxyapatite (HA)/meso-silica was prepared and used as absorbance of methylene blue (MB). HA/meso-silica was synthesized in three steps: preparation of nano-sized HA by wet precipitation method, coating of dense silica and deposition of meso-silica shell on HA. As-received samples were characterized by Fourier transformed infare spectra, small angle X-ray diffraction, nitrogen adsorption-desorption isotherm and transmission electron microscopy. A wormhole framework mesostructure was found for HA/meso-silica. The specific surface area and pore volume were 128 m2•g-1 and 0.36 cm3•g-1, respectively. From the adsorption isotherm, HA/meso-silica with the great specific surface area exhibited a prominent adsorption capacity of MB (134.0 mg/g) in comparison with bare HA (0 mg/g). This study might shed light on surface modification of conventional low-cost adsorbents for removal of organic pollutants from aqueous solutions.

Effects of Carbonation on the Specific Surface BET of Cement Mortar Measured by Two Different Methods: Nitrogen Adsorption and Water Adsorption

2014 ◽  
Vol 931-932 ◽  
pp. 421-425 ◽  
Author(s):  
Son Tung Pham ◽  
William Prince
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Water Adsorption ◽  
Cement Mortar ◽  
Nitrogen Adsorption ◽  
Accelerated Carbonation ◽  
Molecular Sizes ◽  
The Difference ◽  
Adsorption Desorption

The objective of this work was to examine the microstructural changes caused by the carbonation of normal mortar. Samples were prepared and subjected to accelerated carbonation at 20°C, 65% relative humidity and 20% CO2concentration. The evolutions of the pore size distribution and the specific surface area during carbonation were calculated from the adsorption - desorption isotherms of water vapour and nitrogen. Conflicts observed in the results showed that the porous domains explored by these two methods are not the same due to the difference in molecular sizes of nitrogen and water. These two techniques therefore help to complementarily evaluate the effects of carbonation. The study also helped to explain why results in the literature diverge greatly on the influence of carbonation on specific surface area.

Effects of mesoporous structure on grain growth of nanostructured tungsten oxide

2004 ◽  
Vol 19 (9) ◽  
pp. 2687-2693 ◽  
Author(s):  
Lay Gaik Teoh ◽  
Jiann Shieh ◽  
Wei Hao Lai ◽  
Min Hsiung Hon
Keyword(s):  
Activation Energy ◽  
Surface Area ◽  
Grain Growth ◽  
Pore Diameter ◽  
Mesoporous Structure ◽  
Average Pore ◽  
Transmission Electron ◽  
Show Evidence ◽  
Different Temperatures ◽  
Adsorption Desorption

The effects of mesoporous structure on grain growth were investigated in this study. The synthesis was accomplished using block copolymer as the organic template and tungsten chloride as the inorganic precursor. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy, x-ray diffractometry (XRD), transmission electron microscopy, and N2 adsorption/desorption isotherms were used to characterize the microstructures obtained for different temperatures. TGA and XRD analyses demonstrate that copolymers were expelled at 150–250 °C, and mesoporous structure was stable up to 350 °C. The pore diameter and the surface area evaluated from the Barrett-Joyner-Halenda model and Brunauer–Emmett–Teller method indicated that the average pore diameter is 4.11 nm and specific surface area is 191.5 m2/g for 250 °C calcination. Arrhenius equation used to calculate the activation energy for grain growth demonstrates that the activation energy for grain growth was about 38.1 kJ/mol before mesostructure collapse and 11.3 kJ/mol after collapse. These results show evidence of two different mechanisms governing the process of grain growth. The presence of the pore can be related to the obstacle for grain growth.

scholarly journals Synthesis and characterization of porous silica and polyaniline-porous silica composite materials with high surface area

2014 ◽  
Vol 49 (1) ◽  
pp. 1-8
Author(s):  
US Akhtar ◽  
MK Hossain ◽  
MS Miran ◽  
MYA Mollah
Keyword(s):  
Electron Microscopy ◽  
Pore Size ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
Porous Silica ◽  
Nitrogen Adsorption ◽  
High Specific Surface Area ◽  
Molar Ratio ◽  
Cylindrical Pore

Porous silica materials were synthesized from tetraethyl orthosilicate (TEOS) using Pluronic P123 (non-ionic triblock copolymer, EO20PO70O20) as template under acidic conditions which was then used to prepare polyaniline (PAni) and porous silica composites (PAnisilica) at a fixed molar ratio. These materials were characterized by nitrogen adsorption-desorption isotherm measured by Barrett-Joyner- Halenda (BJH) method and pore size distribution from desorption branch and surface area measured by the Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), transmission electron microscopy (TEM), TEM-energy dispersive X-ray (EDX) and Fourier transform infrared (FT-IR) spectroscopy. The composite maintains its structure even after the polymerization and the polymer is dispersed on the inorganic matrix. The rod-like porous silica was about 1?m to 1.5 ?m long and on an average the diameter was in the range of 300- 500 nm. The SEM and TEM images show well ordered 2d hexagonal pore, high specific surface area (850 m2g-1) and uniform pore size of ca. 6.5 nm in diameter. After incorporation of PAni inside the silica pore, framework of porous silica did not collapse and the surface area of the composite was as high as 434 m2g-1 which was 5.5 time higher than our previous report of 78.3 m2g-1. Due to shrinkage of the framework during the incorporation of aniline inside the silica, the pore diameter slightly increase to 7.5 nm but still showing Type IV isotherm and typical hysteresis loop H1 implying a uniform cylindrical pore geometry. DOI: http://dx.doi.org/10.3329/bjsir.v49i1.18847 Bangladesh J. Sci. Ind. Res. 49(1), 1-8, 2014

scholarly journals Physicochemical Study of 3,4-Dichlorophenoxyacetic Acid Intercalated into Hydrotalcite-Like Compound by Ion Exchanged Method

2016 ◽  
Vol 846 ◽  
pp. 440-447
Author(s):  
Sheikh Ahmad Izaddin Sheikh Mohd Ghazali ◽  
Siti Halimah Sarijo ◽  
Mohd Zobir Hussein
Keyword(s):  
Surface Area ◽  
Anion Exchange ◽  
Layered Double Hydroxide ◽  
Nitrogen Adsorption ◽  
Basal Spacing ◽  
Dichlorophenoxyacetic Acid ◽  
Exchange Method ◽  
Type Iv ◽  
Double Hydroxide ◽  
Adsorption Desorption

The intercalation of herbicide, 3,4-dicholorophenoxyacetic acid (3,4D), into zinc-aluminium-layered double hydroxide (LDH) for the formation of a new nanocomposite ZADX, was accomplished via anion exchange method. Due to the intercalation of 3,4D with LDH interlayer domain, basal spacing expanded from 8.9Å in the ZAL to 17.7-19.0 Å in the ZADX. The percentage loading of 3,4D in the ZADX is 51.4 % (w/w). The FTIR spectra of the nanocomposite shows resemblance peaks of the 3,4D and Zn-Al-layered double hydroxide indicating the inclusion of 3,4D into the layered double hydroxide. Surface area of the resulting nanocomposite increased from 1.3 to 7.14 m2g-1 with the nitrogen adsorption-desorption of type IV.

scholarly journals Structural Study of Microporous Xerogels Prepared by Polycondensation of Pyrogallol with Formaldehyde

2010 ◽  
Vol 6 (1) ◽  
pp. 878-883 ◽  
Author(s):  
Rebeh Moussaoui ◽  
Mongi Ben Mosbah ◽  
Younes Moussaoui ◽  
Elimame Elaloui
Keyword(s):  
Specific Surface ◽  
Aqueous Medium ◽  
Surface Area ◽  
Absorption Spectra ◽  
Structural Study ◽  
Perchloric Acid ◽  
Nitrogen Adsorption ◽  
Desorption Isotherms ◽  
Adsorption Desorption ◽  
Ftir Absorption Spectra

Microporous xerogels were prepared by polycondensation of pyrogallol with formaldehyde catalyzed by perchloric acid in aqueous medium. The samples were characterized by FTIR absorption spectra. The micro-porosity and the specific surface area are characterized by nitrogen adsorption - desorption isotherms. The obtained characteristics depend on the conditions of polycondensation.

scholarly journals Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

2021 ◽  
Author(s):  
You Wu ◽  
Zuannian Liu ◽  
Bakhtari Mohammad Fahim ◽  
Junnan Luo
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Adsorption Mechanism ◽  
Nitrogen Adsorption ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Mechanisms ◽  
Adsorption Desorption

Abstract In this study, MIL-101(Fe), MIL-101(Fe,Cu), and Graphene Oxide (GO) /MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOFs-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including reaction time, pH, temperature and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g− 1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m2/g is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe),which are 747.75 and 510.66m2/g respectively. The adsorption mechanism of phosphate is electrostatic attraction, form coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

Sign in / Sign up

Export Citation Format

Share Document