scholarly journals Experimental Strength Evaluation of Bamboo Reinforced Concrete Beams

2021 ◽  
Vol 10 (1) ◽  
pp. 382-388
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Fine Particles ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforced Concrete Beams ◽  
Control Beam ◽  
Ultimate Load Carrying Capacity ◽  
Bamboo Reinforcement

This paper presents the outcome of an experimental investigation of the behavior and strength of reinforced concrete beams with bamboo reinforcement. A total of five beam specimens were tested in flexural under four point (pure bending) loading. A plain concrete beam (B1) served as a control beam. Two specimens (B2 and B3) were longitudinally reinforced with four bamboo culms and steel stirrups. The last two specimens (B4 and B5) had similar longitudinal reinforcement but bamboo pieces were used as shear stirrups. The bamboo culms used in two specimens (B2 & B4) were treated with bitumen along with sprinkling of fine particles of sand to achieve rough surface for better bonding with concrete. The introduction of bamboo reinforcement increased the stiffness, strength, and ductility of beams significantly as compared to the plain concrete beam. The ultimate load carrying capacity of bamboo reinforced concrete beams was found to be 2.49 to 3.29 times that of control beam. The observed ultimate load was 25% and 13% more for specimens with coated reinforcement in case of steel stirrups and bamboo stirrups respectively. The specimen with coated bamboo reinforcementand steel stirrups achieved the highest ultimate load among all specimens.

Numerical Analysis of Reinforced Concrete Beam Strengthened with CFRP or GFRP Laminates

2016 ◽  
Vol 707 ◽  
pp. 51-59 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Rania Khattab
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

The behaviour of reinforced concrete beam strengthened with Carbon Fiber Reinforced Polymer (CFRP) and Glass fiber reinforced polymer GFRP laminates was investigated using finite element models and the results are presented in this paper. The numerical investigation assessed the effect of the configuration of FRP strengthening laminates on the behaviour of concrete beams. The load-deflection behaviour, and ultimate load of strengthened beam were compared to those of un-strengthened concrete beams. It was shown that using U-shaped FRP sheets increased the ultimate load. The stiffness of the strengthed beam also increased after first yielding of steel reinforcing bars. At was also observed that strengthening beams with FRP laminates to one-fourth of the beam span, modifies the failure of the beam from shear-controlled near the end of the unstrengthened beam, to flexure-controlled near mid-span. CFRP produced better results compared GFRP in terms of the ability to enhance the behavior of strengthenened reinforced concrete beams.

Flexural Performance of Reinforced Concrete Built-up Beams with SIFCON

2020 ◽  
Vol 38 (5A) ◽  
pp. 669-680
Author(s):  
Ghazwan K. Mohammed ◽  
Kaiss F. Sarsam ◽  
Ikbal N. Gorgis
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Conventional Concrete ◽  
Flexural Performance ◽  
Load Carrying ◽  
Fiber Concrete

The study deals with the effect of using Slurry infiltrated fiber concrete (SIFCON) with the reinforced concrete beams to explore its enhancement to the flexural capacity. The experimental work consists of the casting of six beams, two beams were fully cast by conventional concrete (CC) and SIFCON, as references. While the remaining was made by contributing a layer of SIFCON diverse in-depth and position, towards complete the overall depths of the built-up beam with conventional concrete CC. Also, an investigation was done through the control specimens testing about the mechanical properties of SIFCON. The results showed a stiffer behavior with a significant increase in load-carrying capacity when SIFCON used in tension zones. Otherwise high ductility and energy dissipation appeared when SIFCON placed in compression zones with a slight increment in ultimate load. The high volumetric ratio of steel fibers enabled SIFCON to magnificent tensile properties.

scholarly journals Influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams

2018 ◽  
Vol 21 (13) ◽  
pp. 1977-1989 ◽  
Author(s):  
Tengfei Xu ◽  
Jiantao Huang ◽  
Arnaud Castel ◽  
Renda Zhao ◽  
Cheng Yang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Natural Frequencies ◽  
Concrete Beams ◽  
Dynamic Stiffness ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Reinforcing Bar ◽  
Sustained Loading ◽  
Inertia Model

In this article, experiments focusing at the influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams are reported. In these experiments, the bond between concrete and reinforcing bar was damaged using appreciate flexural loads. The static stiffness of cracked reinforced concrete beam was assessed using the measured load–deflection response under cycles of loading and unloading, and the dynamic stiffness was analyzed using the measured natural frequencies with and without sustained loading. Average moment of inertia model (Castel et al. model) for cracked reinforced beams by taking into account the respective effect of bending cracks (primary cracks) and the steel–concrete bond damage (interfacial microcracks) was adopted to calculate the static load–deflection response and the natural frequencies of the tested beams. The experimental results and the comparison between measured and calculated natural frequencies show that localized steel–concrete bond damage does not influence remarkably the dynamic stiffness and the natural frequencies both with and without sustained loading applied. Castel et al. model can be used to calculate the dynamic stiffness of cracked reinforced concrete beam by neglecting the effect of interfacial microcracks.

Prediction Scheme of Torsional Strength of Reinforced Concrete Beam

2012 ◽  
Vol 214 ◽  
pp. 306-310
Author(s):  
Han Chen Huang
Keyword(s):  
Genetic Algorithm ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Ann Model ◽  
Torsional Strength ◽  
Prediction Scheme ◽  
Optimal Network

This study proposes a artificial neural network with genetic algorithm (GA-ANN) for predicting the torsional strength of reinforced concrete beam. Genetic algorithm is used to the optimal network structure and parameters. A database of the torsional failure of reinforced concrete beams with a rectangular section subjected to pure torsion was obtained from existing literature for analysis. This study compare the predictions of the GA-ANN model with the ACI 318 code used for analyzing the torsional strength of reinforced concrete beam. The results show that the proposed model provides reasonable predictions of the ultimate torsional strength of reinforced concrete beams and offers superior torsion accuracy compared to that of the ACI 318-89 equation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals RETROFITTING AND DACTILITY OF REINFORCED CONCRETE BEAMS USING AN EXTERNAL REINFORCEMENT METHOD

2019 ◽  
Vol 3 (2) ◽  
pp. 135
Author(s):  
Novita Ike Triyuliani ◽  
Sri Murni Dewi ◽  
Lilya Susanti
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Concrete Block ◽  
Steel Reinforcement ◽  
Reinforced Concrete Beams ◽  
Building Structures ◽  
Average Increase ◽  
External Reinforcement ◽  
Strength And Ductility

The innovations strengthening building structures are important topics. Failure in structures such as beams and columns due to time, re-functions of a building, even initial design errors that are weak or lack the safety factor of a building structure. External reinforced concrete beams are one of the beams currently being developed. It is a concrete block with reinforcement of steel reinforcement on the outer (external) of the beam. This study aims to determine the index of increasing beam strength and ductility after retrofitting external steel reinforcement, which has the dimension of beams 15 x 15 x 100 cm, repeating 12 pcs, with external reinforcement each 6 pcs 2Ø6 and 3Ø6. The results from this study are an increasing the index of beam flexural strength after retrofit with external steel reinforcement. Meanwhile, beams after retrofit with 2Ø6 external steel have an average increase index of 1.25 and 1.21 while for external steel 3Ø6 are 1.29 and 1.60 respectively. The ductility depends on the value of ultimate load and maximum deflection that occurs, where the ductility value for the comparison of each specimen experiences a reduction in the average ductility value with 2Ø6 external steel which is 37.74% and 70.95% while with 3Ø6 external steel is 61,65% and 60.62%. Berbagai inovasi upaya peningkatan kekuatan struktur bangunan telah menjadi bahasan yang penting. Kegagalan pada struktur seperti balok dan kolom karena umur, alih fungsi suatu bangunan, bahkan kesalahan desain awal yang lemah atau kurang memenuhi faktor keamanan suatu struktur bangunan. Balok beton bertulangan eksternal adalah salah satu balok yang sedang dikembangkan pada saat ini, yaitu balok beton dengan perkuatan tulangan baja di sisi terluar (eksternal). Penelitian ini bertujuan untuk mengetahui indeks peningkatan kekuatan balok dan daktilitas setelah dilakukan perbaikan menggunakan tulangan baja eksternal, dengan dimensi balok 15 × 15 × 100 cm berulang 12 buah, penambahan tulangan baja eksternal masingmasing 6 buah 2Ø6 dan 3Ø6. Hasil yang didapat dari penelitian ini adalah indeks peningkatan kekuatan lentur balok setelah dilakukan perbaikan menggunakan tulangan baja eksternal. Dimana balok setelah dilakukan perbaikan dengan baja eksternal 2Ø6 memiliki indeks peningkatan rata-rata 1,25 dan 1,21 sedangkan untuk baja eksternal 3Ø6 masing-masing 1,29 dan 1,60. Daktilitas tergantung dari nilai beban ultimit dan lendutan maksimum yang terjadi, dimana nilai daktilitas untuk perbandingan tiap benda uji mengalami reduksi nilai daktilitas rata-rata dengan baja eksternal 2Ø6 yaitu sebesar 37,74% dan 70,95% sedangkan dengan baja eksternal 3Ø6 sebesar 61,65% dan 60,62%.

scholarly journals DUCTILITY RESPONSE OF HYBRID FIBRE REINFORCED CONCRETE BEAMS

2018 ◽  
pp. 174-179 ◽  
Author(s):  
Eswari Natarajan
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Volume Fraction ◽  
Fibre Volume ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforced Concrete ◽  
Hybrid Fibre ◽  
Service Load ◽  
Strength And Ductility

Abstract: The effect of fibre content on the Strength and ductility behaviour of hybrid fibre reinforced concrete (HFRC) beams having different fibre volume fractions was investigated. The parameters of this investigation included service load, ultimate load, service load deflection, ultimate load deflection, crack width, deflection ductility and energy ductility. The fibre volume fraction (Vf) ranged from 0.0 to 2.0 percent. Steel and polyolefin fibres were combined in different proportions and their impact on the above parameters was studied. The ductile response of hybrid fibre reinforced concrete beams was compared with that of control beam. The test results show that addition of 2.0 percent by volume of hybrid fibres improve the strength and ductility appreciably. Empirical expressions for predicting the strength and ductility of hybrid fibre reinforced concrete (HFRC) are proposed based on regression analysis. A close agreement has been obtained between the predicted and experimental results.

Performance of Reinforced Concrete Beams with Multiple Openings

2020 ◽  
Vol 857 ◽  
pp. 162-168
Author(s):  
Haidar Abdul Wahid Khalaf ◽  
Amer Farouk Izzet
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
Design Parameters ◽  
Ultimate Load Capacity ◽  
Concentrated Load ◽  
Simply Supported ◽  
Group I

The present investigation focuses on the response of simply supported reinforced concrete rectangular-section beams with multiple openings of different sizes, numbers, and geometrical configurations. The advantages of the reinforcement concrete beams with multiple opening are mainly, practical benefit including decreasing the floor heights due to passage of the utilities through the beam rather than the passage beneath it, and constructional benefit that includes the reduction of the self-weight of structure resulting due to the reduction of the dead load that achieves economic design. To optimize beam self-weight with its ultimate resistance capacity, ten reinforced concrete beams having a length, width, and depth of 2700, 100, and 400 mm, respectively were fabricated and tested as simply supported beams under one incremental concentrated load at mid-span until failure. The design parameters were the configuration and size of openings. Three main groups categorized experimental beams comprise the same area of openings and steel reinforcement details but differ in configurations. Three different shapes of openings were considered, mainly, rectangular, parallelogram, and circular. The experimental results indicate that, the beams with circular openings more efficient than the other configurations in ultimate load capacity and beams stiffness whereas, the beams with parallelogram openings were better than the beams with rectangular openings. Commonly, it was observed that the reduction in ultimate load capacity, for beams of group I, II, and III compared to the reference solid beam ranged between (75 to 93%), (65 to 93%), and (70 to 79%) respectively.

scholarly journals Study on the Flexural Performance of Hybrid-Reinforced Concrete Beams with a New Cathodic Protection System Subjected to Corrosion

Materials ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 234 ◽  
Author(s):  
Yingwu Zhou ◽  
Yaowei Zheng ◽  
Lili Sui ◽  
Biao Hu ◽  
Xiaoxu Huang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Steel Corrosion ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Flexural Performance ◽  
Reinforced Polymer ◽  
Steel Bar

Steel corrosion is considered as the main factor for the insufficient durability of concrete structures, especially in the marine environment. In this paper, to further inhibit steel corrosion in a high chloride environment and take advantage of the dual-functional carbon fiber reinforced polymer (CFRP), the impressed current cathodic protection (ICCP) technique was applied to the hybrid-reinforced concrete beam with internally embedded CFRP bars and steel fiber reinforced polymer composite bar (SFCB) as the anode material while the steel bar was compelled to the cathode. The effect of the new ICCP system on the flexural performance of the hybrid-reinforced concrete beam subjected to corrosion was verified experimentally. First, the electricity-accelerated precorrosion test was performed for the steel bar in the hybrid-reinforced beams with a target corrosion ratio of 5%. Then, the dry–wet cycles corrosion was conducted and the ICCP system was activated simultaneously for the hybrid-reinforced concrete beam for 180 days. Finally, the three-point bending experiment was carried out for the hybrid-reinforced concrete beams. The steel bars were taken out from the concrete to quantitatively measure the corrosion ratio after flexural tests. Results showed that the further corrosion of steel bars could be inhibited effectively by the ICCP treatment with the CFRP bar and the SFCB as the anode. Additionally, the ICCP system showed an obvious effect on the flexural behavior of the hybrid-reinforced concrete beams: The crack load and ultimate load, as well as the stiffness, were enhanced notably compared with the beam without ICCP treatment. Compared with the SFCB anode, the ICCP system with the CFRP bar as the anode material was more effective for the hybrid-reinforced concrete beam to prevent the steel corrosion.

Sign in / Sign up

Export Citation Format

Share Document