scholarly journals Heavy metal contamination and water quality of selected fish ponds at Sunyani, Ghana: A comparison with WHO standards

2021 ◽  
Author(s):  
CI Chemistry International
Keyword(s):  
Water Quality ◽  
Heavy Metal ◽  
Physicochemical Parameters ◽  
Heavy Metal Contamination ◽  
Oxygen Demand ◽  
World Health ◽  
Total Hardness ◽  
Fish Ponds ◽  
Long Term Effects ◽  
Health Organization

Optimum fish production is greatly dependent on the physical, chemical and biological qualities of water. Hence, successful fish pond management requires an in-depth understanding of water quality. A study to assess heavy metal (Cr, Cd, Mn, Pb and Zn) contamination and physicochemical parameters of water samples from eight selected fish ponds in Sunyani, Ghana, was conducted. The parameters included temperature, pH, salinity, total hardness, electrical conductivity (EC), chemical oxygen demand (COD) and biological oxygen demand (BOD). The results revealed detectable Mn and Zn levels in all the selected fish ponds; with Mn levels in three ponds being significantly higher than the World Health Organization (WHO) recommended limit (< 0.500 mg/L). Of the three samples, which showed detectable Cr and Cd levels, concentrations of two exceeded the permissible limits. Pb was below the detection limit in all the samples whilst Cu levels detected in two of the ponds were below the permissible limit. The investigated physicochemical parameters had the following ranges: temperature 26-29 C, pH 5.8-8.2, BOD 0.3-20 mg/L, Total Dissolved Solids (TDS) 37-249 mg/L, EC 73.67-498 μS/cm, total hardness 0.8-5.7 mg/L, salinity 0.03-0.22 psu and COD 2.9-9.7 mg/L. Most of these values were within WHO recommended levels. The findings suggest that regular monitoring of the heavy metal load is necessary to guard against long-term effects of its presence in the water, influencing fish and human uptake.

scholarly journals IMPACTS OF DUMPSITE ON SOIL AND GROUNDWATER QUALITY: A CASE STUDY OF ERINFUN COMMUNITY, ADO EKITI, SOUTHWESTERN NIGERIA

2021 ◽  
Vol 5 (2) ◽  
pp. 112-116
Author(s):  
F., F. Akinola ◽  
M., O. Lasisi ◽  
B., S. Awe
Keyword(s):  
Water Quality ◽  
Drinking Water ◽  
Water Sample ◽  
Biochemical Oxygen Demand ◽  
Water Samples ◽  
Physicochemical Parameters ◽  
Oxygen Demand ◽  
Soil Samples ◽  
World Health ◽  
Health Organization

Groundwater pollution has increased as a result of poor waste disposal practices in developing countries. The purpose of this study was to determine the levels of physicochemical parameters and heavy metal concentrations in order to investigate the impact of dumpsites on groundwater and soil quality in Erinfun community. Four (4) water samples were collected hand dug well and four (4) soil samples designated Ss1 to Ss4 were collected at distances of 10, 20, 30 and 40 m, respectively, away from the waste dumpsite. Physicochemical parameters and traces such as odour, colour, taste and temperature, as well as Biochemical Oxygen Demand, Chemical Oxygen Demand, Dissolve Oxygen, Total Dissolve Solid, pH, and chloride were measured in collected water samples. Collected soil samples were also analyzed for heavy metals such as Magnesium, Zinc, Iron, Chromium, and Lead. All the physical parameters of the water samples analysed were found not to be within the acceptable limit of World Health Organization and Nigerian Standard of Drinking Water Quality standards. The chemical constituents tested were within the acceptable limit of World Health Organization and Nigerian Standard of Drinking Water Quality except for the Biochemical Oxygen Demand, Chemical Oxygen Demand and Dissolve Oxygen of water samples 1 and 2, respectively. The concentration of trace metals in water sample test were within health limit except for Magnesium and Iron which has the highest concentrations in water sample 1 at 10 m away from dumpsite (61.00 mg/l and 0.46 mg/l). Consequently, open dumpsites are discouraged, and constructed standard landfills with appropriate monitoring guidelines are recommended.

scholarly journals Water quality profile of fresh water wetland of Atpadi in Sangli District, Maharashtra (India)

2013 ◽  
Vol 14 (3) ◽  
pp. 95-99
Author(s):  
Alaka A. Patil
Keyword(s):  
Water Quality ◽  
Oxygen Demand ◽  
Environmental Parameters ◽  
Biological Oxygen Demand ◽  
Total Alkalinity ◽  
World Health ◽  
Total Hardness ◽  
Quality Profile ◽  
Calcium Magnesium ◽  
Health Organization

This paper presents a study on influence on environmental parameters on water quality at wetland of Atpadi in Atpadi tehsil of Sangli district on the basis of water quality index (WQI). WQI was determined on the basis of various parameters like pH, dissolved oxygen, total alkalinity, total hardness, calcium, magnesium, chlorides, total dissolved solids and biological oxygen demand for which no earlier reports are available on these water bodies. During this investigation, it was observed that some parameters are within the range prescribed by World Health Organization, Indian Council of Medical Research, Bureau of Indian Standard etc. But some parameters are beyond the permissible limit.

Some Physicochemical Parameters of Wastewater from an Oil Industry at Point of Discharge in Port Harcourt, Rivers State, Nigeria

2020 ◽  
Vol 6 (2) ◽  
pp. 23-28
Author(s):  
O. A. F Wokoma ◽  
◽  
O. S Edori ◽  
Keyword(s):  
Physicochemical Parameters ◽  
Oxygen Demand ◽  
Aquatic Organisms ◽  
Oil Industry ◽  
World Health ◽  
Port Harcourt ◽  
Water Association ◽  
Wastewater Samples ◽  
Health Organization ◽  
Rivers State

Wastewater samples were collected from an oil industry at the point of discharge for a period of two years, from January 2018 – December 2019. The wastewater samples were analyzed for different physicochemical parameters such as temperature, turbidity, total dissolved solids (TDS), total suspended solids (TSS), conductivity, pH, alkalinity, salinity, total hydrocarbon content (THC), biochemical oxygen demand (BOD) and chemical oxygen demand (COD) to examine their conformity to fulfill requirements as recommended by World Health Organization (WHO), Federal Ministry of Environment (FME) and Drinking Water Association (DWA). The results indicated that all the parameters in the discharged wastewater were within acceptable limits of the regulatory bodies. The field data showed that the investigated firm conformed to the law by carrying out proper procedures before discharging the effluents into the public drain and river. Therefore, the release of wastewater from the industry doesn't constitute a danger to the environment as well as aquatic organisms. Keywords: Physicochemical parameter, wastewater discharge, oil industry, environment, contaminants

scholarly journals Evaluation of Groundwater Quality in the Vicinity of Khurrianwala Industrial Zone, Pakistan

Water ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1321 ◽  
Author(s):  
Muhammad Aleem ◽  
Cao Shun ◽  
Chao Li ◽  
Arslan Aslam ◽  
Wu Yang ◽  
...  
Keyword(s):  
Water Quality ◽  
Groundwater Quality ◽  
Anthropogenic Activities ◽  
World Health ◽  
Total Hardness ◽  
Industrial Zone ◽  
High Concentration ◽  
Physico Chemical ◽  
Health Organization ◽  
National Environmental

The industrial augmentation and unguided anthropogenic activities contaminate water sources in most parts of the world especially in developing countries like Pakistan. High concentration of pollutants in groundwater affects human, soil, and crop health badly. The present study was conducted to investigate groundwater quality for drinking and irrigation purposes in an industrial zone of Pakistan. A GIS tool was used to investigate the spatial distribution of different physico-chemical parameters. In this study, the average results exceeding World Health Organization (WHO) and National Environmental Quality Standards (NEQS) were found for pH 7.84, total dissolved solids (TDS) 1492 mg/L, phosphate 0.51 mg/L, dissolved oxygen (DO) 9.92% saturation, F-coli 6.48 colonies/100 mL, Na+ 366 mg/L, HCO3− 771 mg/L, sulfate 251 mg/L, chlorides 427 mg/L, total hardness (as CaCO3) 292 mg/L, electrical conductivity (EC) 2408 μS/cm, iron (Fe) 0.48 mg/L, chrome (Cr) 0.50 mg/L, arsenic (As) 0.04 mg/L, total phosphorus (TP) 0.17 mg/L, sodium adsorption ratio (SAR) 9.76 (in meq/L), residual sodium carbonate (RSC) 9.28 meq/L, % ion balance 14.4 (in meq/L), percentage sodium ion (% Na+) concentration 58.9 meq/L, and water quality index (WQI) 69.0. The trend of cations and anions were (in meq/L) Na > Mg > Ca > K and HCO3 > Cl > CO3 > SO4 respectively. Although the results of the present study showed poor conditions of the groundwater for drinking as WQI but and irrigation purposes as SAR, it needs to improve some more conditions for the provision of safe drinking water and irrigation water quality.

scholarly journals Physicochemical Analysis of Surface and Ground Water in Ugbomro and Iteregbi, Delta State, Nigeria

2020 ◽  
Vol 24 (3) ◽  
pp. 511-517
Author(s):  
O.B. Ovonramwen
Keyword(s):  
Oxygen Demand ◽  
Physicochemical Analysis ◽  
Total Alkalinity ◽  
World Health ◽  
Total Hardness ◽  
Need For Treatment ◽  
Environmental Status ◽  
Groundwater Samples ◽  
Health Organization ◽  
Surface And Groundwater

Physicochemical analyses of surface and groundwater samples from eleven different locations in Ugbomro and Iteregbi, Delta State, Nigeria were sampled and analyzed for physicochemical parameters according to standard methods for the examination of water and wastewater. The following  mean and standard deviation were obtained from the groundwater of the communities: temp (oC) 22.46 ± 0.50 and 23.23 ± 0.99, pH 6.63 ± 0.68 and6.69 ± 0.24, dissolved oxygen (DO) (mg/L) 5.91 ± 0.46 and 5.73 ± 0.46, chemical oxygen demand (COD) (mg/L) 4.24 ± 0.01 and 4.43 ± 0.10, biochemical oxygen demand (BOD) (mg/L) 3.51 ± 0.38 and 3.84 ± 0.21, Turbidity (NTU) 1.22 ± 1.07 and 3.56 ± 0.77, electrical conductivity (EC) (μs/cm) 748.9 ± 215.79 and 786.67 ± 226.77, color (TCU) 1.22 ± 2.12 and 6.11 ± 2.11, total alkalinity (TA) (mg/L) 6.22 ± 7.38 and 14.11 ± 11.19, HCO3- (mg/L) 6.22 ± 7.38 and 14.11 ± 11.19, NO3 - (mg/L) 1.13 ± 0.62 and 2.89 ± 1.25, total solids (TS) (mg/L) 489.09 ± 180.17 and 664.95 ± 373.37, total suspended solids (TSS) (mg/L) 32.25 ± 24.29 and 123.86 ± 82.79, total dissolved solids (TDS) (mg/L) 456.78 ± 163.73 and 542.20 ± 450.66, Cl- (mg/L) 21.20 ± 3.20 and 20.10 ± 3.89, total hardness (TH) (mg/L) 26.67 ± 22.83 and 46.78 ± 36.17, Na (mg/L) 1.26 ± 0.06 and 1.16 ± 0.04, K (mg/L) 0.04 ± 0.01 and 0.06 ± 0.03, Mg (mg/L) 4.32 ± 3.23 and 6.96 ± 5.49, Ca (mg/L) 8.68 ± 9.35 and 18.12 ± 13.71 respectively. The results obtained were subjected to statistical analysis and compared with the standard set by the Standards Organization of Nigeria (SON) and the World Health Organization (WHO) for water samples. Some of the parameters did not meet the standards, hence the need for treatment. The present physio-chemical analyses of surface and groundwater quality of the two neighboring university areas, Ugbomro and Iteregbi, were done to assess the environmental status of  the environment before socio-economic impacts. Keywords: physicochemical, surface water, groundwater, water quality

scholarly journals A Detailed Assessment of Groundwater Quality in the Kabul Basin, Afghanistan, and Suitability for Future Development

Water ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2890 ◽  
Author(s):  
Hussain Ali Jawadi ◽  
Jay Sagin ◽  
Daniel D. Snow
Keyword(s):  
Water Quality ◽  
Future Development ◽  
Poor Quality ◽  
Physicochemical Analysis ◽  
World Health ◽  
Total Hardness ◽  
Human Consumption ◽  
Water Type ◽  
Dissolved Solids ◽  
Health Organization

Kabul is one of the most populated cities in Afghanistan and providing resources to support this population in an arid climate presents a serious environmental challenge. The current study evaluated the quality of local Kabul Basin groundwater to determine its suitability water for drinking and irrigation purposes now and into the future. This aim was aided through groundwater parameter assessment as well as determination of Water Quality Index (WQI) developed from 15 observation points near the city. The results of our physicochemical analysis illustrate that groundwater in the majority of areas of the Kabul Basin is not generally suitable for human consumption, and in some cases the concentrations of many contaminants are higher than accepted health standards or water quality benchmarks. The aquifer underlies an arid landscape, and because of this 85% of the samples tested are very hard while just over 13% are classified as hard. Groundwater in the Kabul Basin is typically high in calcium and magnesium and overall classified as a calcium bicarbonate water type. Overall, more than 60% of the analyzed samples had concentrations higher than the World Health Organization (WHO) standard of total dissolved solids (TDS), 10% in total hardness (TH), about 30% in turbidity and more than 90% in magnesium. The results show that based on WQI, without treatment, roughly 5% of groundwater in the studied area is unsuitable for human consumption, while 13.3% is very poor and 40% is poor quality water. Approximately 40% of the assessed groundwater has good quality and could be used as drinking water for future development. Groundwater in some areas shows evidence of pollution and high dissolved solids content, rendering these sources unsuitable for either drinking or irrigation purposes.

scholarly journals Ground Water Quality of Gandhinagar Taluka, Gujarat, India

2008 ◽  
Vol 5 (3) ◽  
pp. 435-446 ◽  
Author(s):  
Mayur C. Shah ◽  
Prateek G. Shilpkar ◽  
Pradip B. Acharya
Keyword(s):  
Water Quality ◽  
Dissolved Oxygen ◽  
Water Samples ◽  
Oxygen Demand ◽  
Total Alkalinity ◽  
World Health ◽  
Total Hardness ◽  
Drinking And Irrigation ◽  
Quality Of Water

Present communication deals with study of physico-chemical parameters such as pH, electrical conductivity (EC), total dissolved solids (TDS), total alkalinity (TA), calcium hardness (CaH), magnesium hardness (MgH), total hardness (TH), chloride (Cl-), fluoride (F-), sodium (Na+), potassium (K+), dissolved oxygen (DO), biochemical oxygen demand (BOD), chemical oxygen demand (COD) and sulphate (SO42-) of water samples of bore wells of forty villages of Gandhinagar taluka of Gujarat state,India. The experimental values of water samples were compared with standard values given by World Health Organization (WHO) and United State Salinity Laboratory for drinking and irrigation purposes respectively. Water Quality Index (WQI) was also calculated to know the over all quality of water samples. The statistical analysis like mean, standard deviation (SD), coefficient of variance (% CV), analysis of variance (ANOVA),t-test, coefficient of correlation (r) and regression analysis of obtained data were carried out. The results show that the quality of water is poor and quite good for drinking and irrigation purposes respectively. The variance was found significant at 1% level of significance in case of sodium and potassium content and at 5% in case of total alkalinity and dissolved oxygen among the four regions (North, South, East and West) of Gandhinagar taluka. The linear relation also established for each pair of water quality parameters of studied water samples.

scholarly journals Biodegradation of Pollutants in Waste Water from Pharmaceutical, Textile and Local Dye Effluent in Lagos, Nigeria

2016 ◽  
Vol 6 (12) ◽  
pp. 34-42 ◽  
Author(s):  
Idowu A. Aneyo ◽  
Funmilayo V. Doherty ◽  
Olumide A. Adebesin ◽  
Mariam O. Hammed
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Physicochemical Parameters ◽  
Low Cost ◽  
Environmental Pollutants ◽  
Oxygen Demand ◽  
Industrial Effluents ◽  
World Health ◽  
Klebsiella Pneumonia ◽  
The World

Background. Discharged effluents from industry have been responsible for the deterioration of the aquatic environment in many parts of the world, especially in developing countries. Increasing industrialization and urbanization have resulted in the discharge of large amounts of waste into the environment, resulting in high pollution loads. Utilization of microbes such as fungi and bacteria have been used for pollution degradation. Objectives. The aim of this research was to utilize microbial agents such as fungi and bacteria to reduce pollutant loads such as heavy metals in effluent samples. Methods. Three types of effluent (pharmaceutical, textile effluent, and dye) were obtained from Surulere in Lagos Metropolitan Area, Nigeria. Heavy metals analysis was carried out using a flame atomic adsorption spectrophotometer according to standard methods. Samples were cultured for microbes and identified. Bacteria samples were inoculated on nutrient agar and incubated at 37°C for 24 hours. Fungi counts were carried out using potato dextrose agar and incubated at 28°C for 3–5 days. The isolated organisms were identified based on their morphological and biochemical characteristics. Then 100 mL of the effluents was dispensed into 250 mL flasks, and the pH of the medium was adjusted to 7.2 by the addition of either sodium hydroxide or hydrogen chloride and autoclaved at 121°C for 15 minutes. The autoclaved flask was inoculated with 1 mL of bacteria and fungi for 21 days and pH was recorded properly every 48 hours. Results. The results of the physicochemical parameters indicated that conductivity, total suspended solids, total dissolved solids, turbidity, chemical oxygen demand and biochemical oxygen demand for all the three industrial effluents were higher than the World Health Organization (WHO) permissible limits. Heavy metal analysis results show that the effluents had high values for cadmium, above the WHO limit of 0.003 mg/L. Concentrations of zinc ranged from 0.136–1.690 mg/L, and nickel ranged between 0.004–0.037mg/L for the three effluents, within the WHO limit. The identified bacteria were Bacillus subtilis, Klebsiella pneumonia, Salmonella typhi and Bacillus cereus and isolated fungi were Aspergillus flavus and Penicillium chrysogenum. All the physicochemical parameters and heavy metal concentrations were reduced after the biodegradation study in the effluents. Conclusions. The responses observed in the various microbes indicated that the use of microbes for the reduction of environmental pollutants has an advantage over the use of other methods because it is environmentally friendly, low cost, and no new chemicals are introduced into the environment. This method should be encouraged for pollution reduction to bring about ecosystem sustainability advocated for Ghana.

scholarly journals Groundwater quality assessment near a Nigerian dumpsite

1970 ◽  
Vol 10 (5) ◽  
pp. 588-596
Author(s):  
O.A. Mokuolu ◽  
S.O. Jacob ◽  
A.M. Ayanshola
Keyword(s):  
Water Quality ◽  
Drinking Water ◽  
Ground Water ◽  
Solid Waste ◽  
Oxygen Demand ◽  
Chloride Ion ◽  
World Health ◽  
Total Hardness ◽  
Human Consumption ◽  
Groundwater Assessment

Municipal solid waste collected in Nigeria are often disposed of in uncontrolled dumpsites and/or burnt in the open spaces and consequently causing significant pollution on surface water, ground water and the air. An investigational study was carried out on the level of pollution on groundwater near Gbagede dumpsite in Kwara state. Ground water samples, GW1, GW2, GW3 were taken at three different locations: 186 m, 290 m, and 326 m from the edge of the dumpsite. Physicochemical parameters evaluated include; pH, total hardness, Total Dissolved Solids, Total Suspended Solids, alkalinity, turbidity, Chemical Oxygen Demand, Biochemical Oxygen Demand, Dissolved Oxygen, Nitrate ion, Chloride ion, Sulphate ion, Electrical conductivity, Calcium ion and Magnesium ion using standard laboratory procedures. The results of the evaluations were compared with the World Health Organization (WHO) and Nigerian Standard for Drinking Water Quality (NSDWQ) to establish its suitability for human consumption. Results fell within the stipulated range of WHO and NSDWQ standard for drinking water. It was however observed that the water quality improves with distance from the dumpsite. Statistical analyses indicated mild differences among all the parameters tested for in the samples at 95% confidence level. Uncontrolled accumulation of leachates from the dumpsite may pose potential risk to the source of water for the community in the near future. It was recommended that the dumpsite be relocated from the current residential area.Key Words: Groundwater, Assessment, Contaminants, Solid-waste, Water quality

scholarly journals Preliminary Assessment of Water Quality in Some Hydrocarbon-imparted Ogoni Communities in River State, Nigeria

2021 ◽  
pp. 88-97
Author(s):  
Caroline Barituka Ganabel ◽  
Confidence Kinikanwo Wachukwu ◽  
Samuel Douglas Abbey ◽  
Easter Godwin Nwokah
Keyword(s):  
Water Quality ◽  
Heavy Metal ◽  
Drinking Water ◽  
Water Samples ◽  
Physicochemical Parameters ◽  
Pearson Correlation ◽  
Statistical Significance ◽  
World Health ◽  
Most Probable Number ◽  
Probable Number

Aim: This study aimed to assess the quality of drinking water in some hydrocarbon-impacted Ogoni communities. Study Design: The study employ a cross-sectional and analytical design using stratified sampling method. Place and Duration of Study: Department of Medical Laboratory Science of Rivers State University, Giolee Global Resource Limited and Environmental Consultancy Services between March 2020 and March 2021. Methodology: Water samples were collected from (20 hydrocarbon- impacted communities) in the 4 Local Government Area (LGAs) of Ogoni land. These water samples were analyzed to determine the physicochemical, bacteriological, heavy metal and total petroleum hydrocarbon (TPH) parameters using standard methods and operational procedures. The data obtained were subjected to descriptive statistical analysis. The general linearized model (GIG) was used to generate analysis of variance (ANOVA) mean and standard error and arrange, statistically significant was set as p-value of .05 (95% confidence limit). Pearson correlation test was used to calculate the correlation between TPH, Heavy metal, and physicochemical parameters in hydrocarbon and non-hydrocarbon impacted communities. All statistical analyses were performed using GraphPad Prism (Version 8). Results: The results obtained for physicochemical parameters were pH 4.3±0.8 mg/l, EC 0.03±0.05 mg/l, DO 5.5±1.6 mg/l, Temp 25.0±0.0 mg/l, Mv 0.32±0.27 mg/l, Nitrite 0.0058±013 mg/l, Nitrate 0.1530±158 mg/l. These results were all below the recommended standard for Nigeria standard of drinking water quality (NSDWQ) and World Health Organization (WHO). The bacteriological analyses were carried out using multiple tubes technique (Most Probable Number), total coliform count, (TC), total heterotrophic count (THBC) and total fungal count (TFC). The results obtained were 0.941±2.397 cfu/ml, 89.3±176.6 cfu/ml, 297.8±144.4 cfu/ml, and 0.32±0.84 cfu/ml respectively. The p-values for TFC (<0.0002) were statistically significant. Heavy metal profiling was: Cr 0.194±0.320 mg/l, Cd 0.469±0.569 mg/l, Cu 0.211±0.348 mg/l, Pb 0.0336±0.20 mg/l, Fe 0.705±1.244 mg/l, Zn 0.258±0.249 mg/l, respectively. Generally, the concentration of heavy metal   increased more than the standard recommended by NSDWQ and WHO except for Zn 0.255±0.249 mg/l, and Cu 0.56±0.50 mg/l, that is slightly lower than the acceptable limit recommended by WHO and NSWWQ. The sequences of heavy metal concentration were in Cd > Cr> Pb>Fe> Cu.>Zn. The statistical significance values for Pb p=.003 and for Zn p=.009 were statistically significant. The concentration of TPH were (349.9 ppm/ml) higher than the recommended values for NSDWQ and WHO. Conclusion: The findings in this research reviewed a worrisome level of TPH and Pb, and which could have devastating impact on bacterial biodiversity.

Sign in / Sign up

Export Citation Format

Share Document